Operator's Manual

ManualsBrandsToro ManualsSnow ThrowerToro 38711

FormNo.3396-391RevA

SnowMax724/824QXESnowthrower

ModelNo.38711—SerialNo.316000001andUp

ModelNo.38712—SerialNo.316000001andUp

Operator'sManual

Introduction

Thismachineisintendedtobeusedbyresidential

homeowners.Itisdesignedforremovingsnowfrom

pavedsurfaces,suchasdrivewaysandsidewalks,and

othersurfacesfortrafconresidentialorcommercial

properties.Itisnotdesignedforremovingmaterials

otherthansnow,norisitdesignedforclearingoffgravel

surfaces.

Readthisinformationcarefullytolearnhowtooperateand

maintainyourmachineproperlyandtoavoidinjuryand

machinedamage.Youareresponsibleforoperatingthe

machineproperlyandsafely.

YoumaycontactTorodirectlyatwww .Toro.comformachine

andaccessoryinformation,helpndingadealer,ortoregister

yourmachine.

Wheneveryouneedservice,genuineToroparts,oradditional

information,contactanAuthorizedServiceDealerorToro

CustomerServiceandhavethemodelandserialnumbersof

yourmachineready.Figure1identiesthelocationofthe

modelandserialnumbersonthemachine.Writethenumbers

inthespaceprovided.

Figure1

1.Modelandserialnumberlocation

ModelNo.

SerialNo.

Thismanualidentiespotentialhazardsandhassafety

messagesidentiedbythesafetyalertsymbol(Figure2),

whichsignalsahazardthatmaycauseseriousinjuryordeath

ifyoudonotfollowtherecommendedprecautions.

Figure2

1.Safetyalertsymbol

Thismanualuses2wordstohighlightinformation.

Importantcallsattentiontospecialmechanicalinformation

andNoteemphasizesgeneralinformationworthyofspecial

attention.

Formodelswithstatedpower,thenetpoweroftheenginewas

laboratoryratedbytheenginemanufacturerinaccordance

withSAEJ1940.Asconguredtomeetsafety,emission,and

operatingrequirements,theactualenginehorsepoweronthis

classofsnowthrowerwillbesignicantlylower.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3396-391*A

Summary of content (20 pages)

PAGE 1
Form No. 3396-391 Rev A SnowMax 724/824 QXE Snowthrower Model No. 38711—Serial No. 316000001 and Up Model No. 38712—Serial No. 316000001 and Up Operator's Manual Introduction which signals a hazard that may cause serious injury or death if you do not follow the recommended precautions. This machine is intended to be used by residential homeowners.
PAGE 2
Contents Safety Introduction .................................................................. 1 Safety ........................................................................... 2 Sound Pressure ....................................................... 2 Sound Power .......................................................... 2 Vibration................................................................ 2 Safety and Instructional Decals ................................. 3 Setup ...............................
PAGE 3
Safety and Instructional Decals Note: Safety and instruction decals are located near areas of potential danger. Replace damaged decals. 131–1785 Order part no. 131–5921 1. Auger drive—squeeze the lever to engage; release the lever to disengage. 4. Thrown object hazard—keep bystanders a safe distance from the snowthrower. 2. Warning—read the Operator's Manual. 5. Self-propel drive—push down on the handle to engage the self-propel drive. 3.
PAGE 4
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Use 1 No parts required – Unfold the handle. 2 Bolt (1/4–20 X 1–1/2 inch) Lock nut (1/4–20 inch) Carriage bolt (1/4–20 x 1 inch) Lock nut (1/4–20 inch) Screw (1/4–20 X 5/8 inch) 1 1 3 3 1 Install the discharge chute. 1 Unfolding the Handle No Parts Required Procedure Important: Ensure that the cables are not pinched when unfolding the handle.
PAGE 5
2 Installing the Discharge Chute Parts needed for this procedure: 1 Bolt (1/4–20 X 1–1/2 inch) 1 Lock nut (1/4–20 inch) 3 Carriage bolt (1/4–20 x 1 inch) 3 Lock nut (1/4–20 inch) 1 Screw (1/4–20 X 5/8 inch) Procedure 1. Insert the chute post through the bracket into the base of the machine and secure it using a bolt and a lock nut (Figure 4). Figure 5 Figure 4 1. Chute post 3. Lock nut (1/4–20 inch) 2. Bolt (1/4–20 X 1–1/2 inch) 4. Bracket 1. Chute rod 4. Cable clip 2.
PAGE 6
3 Filling the Engine with Oil No Parts Required Procedure Your machine comes with oil in the engine. Model Max fill 38711 0.5 L (16.9 oz) 38712 0.7 L (23.7 oz) Oil type: automotive detergent oil with an API service classification of SJ, SL, or higher. Use Figure 6 below to select the best oil viscosity for the outdoor temperature range expected: Figure 6 1. Move the machine to a level surface. 2. Clean around the oil-fill cap. 3. Check the oil level and add oil if necessary.
PAGE 7
Product Overview Operation Before Operation Safety • Use extension cords and receptacles as specified by • • • • Figure 8 1. Auger lever 6. Scraper 2. Fuel tank cap 7. Discharge chute 3. Dipstick 8. Chute deflector 4. Skid 5. Auger the manufacturer for all machines with electric starting motors. Do not operate the machine without wearing adequate winter garments. Avoid loose fitting clothing that can get caught in moving parts.
PAGE 8
• • • • Exercise extreme caution when operating on slopes. than 10% ethanol by volume, such as E15 (contains 15% ethanol), E20 (contains 20% ethanol), or E85 (contains 85% ethanol). Using unapproved gasoline may cause performance problems and/or engine damage which may not be covered under warranty. Do not use gasoline containing methanol. Do not store fuel either in the fuel tank or fuel containers over the winter unless a fuel stabilizer is used. Do not add oil to gasoline.
PAGE 9
Using the Recoil Starter Using the Electric Starter Figure 11 Figure 12 Note: To use the electric starter, connect a power cord to the electric starter plug-in first and then to a power outlet. Use only a UL-listed, 16-gauge extension cord recommended for outdoor use that is not longer than 15 m (50 feet). Important: To prevent damaging the electric starter, run it in short cycles (5 seconds on, 5 seconds off), no more than 10 times.
PAGE 10
WARNING The electrical cord can become damaged, causing a shock or fire. Thoroughly inspect the electrical cord before using the machine. If the cord is damaged, do not operate the machine. Replace or repair the damaged cord immediately. Contact an Authorized Service Dealer for assistance. CAUTION If you leave the machine plugged into a power source, someone can inadvertently start the machine and injure people or damage property. Figure 14 Unplug the power cord whenever you are not starting the machine.
PAGE 11
Clearing a Clogged Discharge Chute water heaters, space heaters, or clothes dryers. Allow the engine to cool before storing in any enclosure. • When storing the machine for more than 30 days, refer to Important: Hand contact with the rotating auger inside the discharge chute is the most common cause of injury associated with snowthrowers. Never use your hand to clean out the discharge chute. the Storage section for important details. Preventing Freeze-up after Use 1.
PAGE 12
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first hour • Check for loose fasteners and tighten them if necessary. After the first 2 hours • Change the engine oil. • Inspect the auger cable and adjust it if necessary. • Inspect the transmission cable and adjust it if necessary.
PAGE 13
Checking and Adjusting the Skids Inspecting the Throwing Edges Service Interval: Yearly Service Interval: Yearly—Inspect the throwing edges and have an Authorized Service Dealer replace the throwing edges and scraper if necessary. Check the skids to ensure that the auger does not contact the paved surface. Adjust the skids as needed to compensate for wear (Figure 17). Before each session, inspect the throwing edges for wear.
PAGE 14
Figure 19 1. Oil-drain plug 3. After draining the used oil, return the machine to the operating position. 4. Install the oil drain plug and tighten it securely. 5. Clean around the oil fill cap. 6. Use Figure 20 below to select the best oil viscosity for the outdoor temperature range expected: Model Max fill 38711 0.5 L (16.9 oz) 38712 0.7 L (23.7 oz) Oil type: automotive detergent oil with an API service classification of SJ, SL, or higher. Figure 20 Figure 21 1. Low oil level—add oil 14 2.
PAGE 15
Replacing the Spark Plug 1. Loosen the nut on the lower cable clamp, but do not remove it (Figure 24). Service Interval: Every 100 hours—Replace the spark plug. WARNING Replacing the spark plug while the engine is hot can result in burns. Wait until the engine is cool to replace the spark plug. Use a Toro spark plug or equivalent (Champion® RN9YC or NGK BPR6ES). 1. Remove the boot (Figure 22). Figure 24 1. Nut 2. Cable 3. Connector 4. Spring 2. Pull the cable up to remove some slack (Figure 24).
PAGE 16
Storage Storing the Snowthrower WARNING • Gasoline fumes are highly flammable, explosive, and dangerous if inhaled. If you store the machine in an area with an open flame, the gasoline fumes may ignite and cause an explosion. • Do not store the machine in a house (living area), basement, or any other area where ignition sources may be present, such as hot water and space heaters, clothes dryers, furnaces, and other like appliances.
PAGE 17
16. Cover the machine and store it in a clean, dry place out of the reach of children. Allow the engine to cool before storing it in any enclosure.
PAGE 18
Notes: 18
PAGE 19
International Distributor List Distributor: Agrolanc Kft Asian American Industrial (AAI) B-Ray Corporation Brisa Goods LLC Casco Sales Company Ceres S.A. CSSC Turf Equipment (pvt) Ltd. Cyril Johnston & Co. Cyril Johnston & Co. Fat Dragon Femco S.A. FIVEMANS New-Tech Co., Ltd ForGarder OU G.Y.K. Company Ltd. Geomechaniki of Athens Golf international Turizm Hako Ground and Garden Hako Ground and Garden Hayter Limited (U.K.) Hydroturf Int. Co Dubai Hydroturf Egypt LLC Irrimac Irrigation Products Int'l Pvt Ltd.
PAGE 20
Residential Snow Products The Toro Warranty and The Toro GTS Starting Guarantee Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly promise to repair for the original purchaser1 the Toro Product listed below if defective in materials or workmanship or if the Toro GTS (Guaranteed to Start) engine will not start on the first or second pull, provided the routine maintenance required in the Operator's Manual have been perform