Operator's Manual

ManualsBrandsToro ManualsSnow ThrowerToro 38712

FormNo.3407-113RevA

SnowMax724and824QXESnowthrower

ModelNo.38711—SerialNo.400010798andUp

ModelNo.38712—SerialNo.400010798andUp

Operator'sManual

ThisproductcomplieswithallrelevantEuropeandirectives.

Fordetails,seetheseparateproductspecicDeclarationof

Conformity(DOC)sheet.

Introduction

Thismachineisintendedtobeusedbyresidential

homeowners.Itisdesignedforremovingsnowfrom

pavedsurfaces,suchasdrivewaysandsidewalks,and

othersurfacesfortrafconresidentialorcommercial

properties.Itisnotdesignedforremovingmaterials

otherthansnow,norisitdesignedforclearingoffgravel

surfaces.

Readthisinformationcarefullytolearnhowtooperateand

maintainyourmachineproperlyandtoavoidinjuryand

machinedamage.Youareresponsibleforoperatingthe

machineproperlyandsafely.

YoumaycontactTorodirectlyatwww .Toro.comformachine

andaccessoryinformation,helpndingadealer,ortoregister

yourmachine.

Wheneveryouneedservice,genuineToroparts,oradditional

information,contactanAuthorizedServiceDealerorToro

CustomerServiceandhavethemodelandserialnumbersof

yourmachineready.Figure1identiesthelocationofthe

modelandserialnumbersonthemachine.Writethenumbers

inthespaceprovided.

Figure1

1.Modelandserialnumberlocation

ModelNo.

SerialNo.

Thismanualidentiespotentialhazardsandhassafety

messagesidentiedbythesafety-alertsymbol(Figure2),

whichsignalsahazardthatmaycauseseriousinjuryordeath

ifyoudonotfollowtherecommendedprecautions.

Figure2

1.Safety-alertsymbol

Thismanualuses2wordstohighlightinformation.

Importantcallsattentiontospecialmechanicalinformation

andNoteemphasizesgeneralinformationworthyofspecial

attention.

Formodelswithstatedpower,thenetpoweroftheenginewas

laboratoryratedbytheenginemanufacturerinaccordance

withSAEJ1940.Asconguredtomeetsafety,emission,and

operatingrequirements,theactualenginehorsepoweronthis

classofsnowthrowerwillbesignicantlylower.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3407-113*A

Summary of content (24 pages)

PAGE 1
Form No. 3407-113 Rev A SnowMax 724 and 824 QXE Snowthrower Model No. 38711—Serial No. 400010798 and Up Model No. 38712—Serial No. 400010798 and Up Operator's Manual This product complies with all relevant European directives. For details, see the separate product specific Declaration of Conformity (DOC) sheet. Model No. Serial No. Introduction This machine is intended to be used by residential homeowners.
PAGE 2
Important: If you are using this machine above 1500 m (5,000 ft) for a continuous period, ensure that the High Altitude Kit has been installed so that the engine meets CARB/EPA emission regulations. The High Altitude Kit increases engine performance while preventing spark-plug fouling, hard starting, and increased emissions. Once you have installed the kit, attach the high-altitude label next to the serial decal on the machine.
PAGE 3
Safety • Keep clear of any discharge opening. Keep bystanders a This machine is designed in consideration of the standards in effect at the time of production. • Keep children out of the operating area. Never allow • Read and understand the contents of this Operator’s • Shut off the engine before unclogging, servicing, or safe distance away from the machine. children to operate the machine. fueling the machine. Manual before you start the engine.
PAGE 4
131-1785 Order Part No. 131-5921 1. Auger drive—squeeze the lever to engage; release the lever to disengage. 4. Thrown object hazard—keep bystanders a safe distance away from the snowthrower. 2. Warning—read the Operator's Manual. 5. Self-propel drive—push down on the handle to engage the self-propel drive. 3.
PAGE 5
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Use 1 No parts required – Unfold the handle. 2 Bolt (1/4–20 X 1–1/2 inches) Locknut (1/4–20 inch) Carriage bolt (1/4–20 x 1 inch) Locknut (1/4–20 inch) Screw (1/4–20 X 5/8 inch) 1 1 3 3 1 Install the discharge chute. 3 No parts required – Fill the engine with oil.
PAGE 6
2 Installing the Discharge Chute Parts needed for this procedure: 1 Bolt (1/4–20 X 1–1/2 inches) 1 Locknut (1/4–20 inch) 3 Carriage bolt (1/4–20 x 1 inch) 3 Locknut (1/4–20 inch) 1 Screw (1/4–20 X 5/8 inch) Procedure 1. Insert the chute post through the bracket into the base of the machine and secure it using a bolt and a locknut (Figure 5). Figure 6 Figure 5 1. Chute post 3. Locknut (1/4–20 inch) 2. Bolt (1/4–20 X 1–1/2 inches) 4. Bracket 1. Chute rod 4. Cable clip 2.
PAGE 7
3 Filling the Engine with Oil No Parts Required Procedure Your machine comes with oil in the engine. Model Max fill 38711 0.5 L (16.9 oz) 38712 0.7 L (23.7 oz) Oil type: automotive detergent oil with an API service classification of SJ, SL, or higher. Use Figure 7 below to select the best oil viscosity for the outdoor temperature range expected: Figure 7 1. Move the machine to a level surface. 2. Clean around the oil-fill cap. 3. Check the oil level and add oil if necessary.
PAGE 8
Product Overview Operation Before Operation Safety • Use extension cords and receptacles as specified by the manufacturer for all machines with electric-starting motors. • Do not operate the machine without wearing adequate winter garments. Avoid loose fitting clothing that can get caught in moving parts. Wear slip resistant footwear that will improve footing on slippery surfaces.
PAGE 9
• Use extension cords and receptacles as specified by the manufacturer for all machines with electric-starting motors. • Do not attempt to clear snow from a gravel or crushed rock surface. This product is intended for use only on paved surfaces. • Do not use the machine on a roof. • Never attempt to make any adjustments while the engine is running (except when specifically recommended by manufacturer). • Stay alert for hidden hazards or traffic.
PAGE 10
Using the Electric Starter Using the Recoil Starter Figure 12 Figure 13 Note: Prime the engine in B of Figure 12 according to the prime table.
PAGE 11
Self-Propelling the Machine To use the electric starter (electric start only), connect a power cord to the electric-start plug-in first and then to a power source with a residual-current device (RCD). Use only a H05VV-F or H05RN-F power cord recommended for outdoor use that is not longer than 15 m (for a 1.0 mm² cord) or 30 m (for a 1.5 mm² cord).
PAGE 12
Operating Tips WARNING The auger can throw stones, toys, and other foreign objects and cause serious personal injury to the operator or to bystanders. • Keep the area to be cleared free of all objects that the rotor blades could pick up and throw. • Keep all children and pets away from the area of operation. • Remove the snow as soon as possible after it falls.
PAGE 13
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first hour • Check for loose fasteners and tighten them if necessary. After the first 2 hours • Change the engine oil. • Inspect the auger cable and adjust it if necessary. • Inspect the transmission cable and adjust it if necessary.
PAGE 14
Checking and Adjusting the Skids Inspecting the Throwing Edges Service Interval: Yearly Service Interval: Yearly—Inspect the throwing edges and have an Authorized Service Dealer replace the throwing edges and scraper if necessary. Check the skids to ensure that the auger does not contact the paved surface. Adjust the skids as needed to compensate for wear (Figure 18). Before each session, inspect the throwing edges for wear.
PAGE 15
Figure 20 1. Oil-drain plug 3. After draining the used oil, return the machine to the operating position. 4. Install the oil-drain plug and tighten it securely. 5. Clean around the oil-fill cap. 6. Use Figure 21 below to select the best oil viscosity for the outdoor temperature range expected: Model Max fill 38711 0.5 L (16.9 oz) 38712 0.7 L (23.7 oz) Oil type: automotive detergent oil with an API service classification of SJ, SL, or higher. Figure 21 Figure 22 1. Low oil level—add oil 15 2.
PAGE 16
Replacing the Spark Plug Adjusting the Auger Cable Service Interval: Every 100 hours—Replace the spark plug. Service Interval: After the first 2 hours Yearly WARNING If the drive belt slips or squeals under heavy load, adjust the auger cable. Replacing the spark plug while the engine is hot can result in burns. 1. Loosen the nut on the lower cable clamp, but do not remove it (Figure 25). Wait until the engine is cool to replace the spark plug.
PAGE 17
Figure 26 1. Nut 2. Cable 2. Pull the cable down to remove most of the slack in the cable (Figure 26). Important: Do not remove all the slack from the cable. Removing all the slack from the cable may cause the wheels to engage without engaging the self-propel handle. 3. Tighten the nut (Figure 26). Checking the Tire Pressure Service Interval: Yearly Set the tire pressure equally in both tires to between 103 and 137 kPa (15 and 20 psi).
PAGE 18
Storage 16. Cover the machine and store it in a clean, dry place out of the reach of children. Allow the engine to cool before storing it in any enclosure. Storing the Snowthrower WARNING • Gasoline fumes are highly flammable, explosive, and dangerous if inhaled. If you store the machine in an area with an open flame, the gasoline fumes may ignite and cause an explosion.
PAGE 19
Notes:
PAGE 20
Notes:
PAGE 21
European Privacy Notice The Information Toro Collects Toro Warranty Company (Toro) respects your privacy. In order to process your warranty claim and contact you in the event of a product recall, we ask you to share certain personal information with us, either directly or through your local Toro company or dealer. The Toro warranty system is hosted on servers located within the United States where privacy law may not provide the same protection as applies in your country.
PAGE 22
Emission Control Warranty Statement For the United States, California, and Canada *374-0320* Your Warranty Rights and Obligations The California Air Resources Board (CARB), the U.S. Environmental Protection Agency (EPA), and The Toro Company, are pleased to explain the emission control system warranty on your 2017–2018 small off-road engine/equipment. In California and the United States, new small off-road engines/equipment must be designed, built, and certified to meet stringent anti-smog standards.
PAGE 23
1. Fuel System Parts • • • • • • 2. Fuel tank, cap, and tether Carbon canister Air cleaner Intake manifold Crankcase vent and line(s) Purge line and fittings Spark plug(s) and wire(s) Magneto ignition system Catalytic Exhaust System • • • 5. Fuel line, fittings, and clamps Ignition System • • 4. Fuel pump Air Induction System • • • • 3.
PAGE 24
Residential Snow Products (Int’l) The Toro Warranty and The Toro GTS Starting Guarantee Conditions and Products Covered Items and Conditions Not Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly promise to repair the Toro Product listed below if defective in materials or workmanship or if the Toro GTS (Guaranteed to Start) engine will not start on the first or second pull, provided the routine maintenance required in the Operator's Manual ha