Installation Instructions

ManualsBrandsToro ManualsAttachmentsPro Control Spray System Upgrade Kit, 2010 Multi-Pro 5700 Turf Sprayer

FormNo.3370-544RevA

ProControl™SpraySystemUpgradeKit

2009andBeforeMulti-Pro

5600/5700TurfSprayer

ModelNo.41008—SerialNo.312000001andUp

ModelNo.41009—SerialNo.312000001andUp

InstallationInstructions

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nipple2

Teetting

Elbow2

Agitationnozzle1

Nut1

Installtheagitationnozzleassembly.

90degreehosebard1

Straighthosebarb

Tee1

Fork4

Adaptor1

Hosebarb(41008)

Agitationvalveassembly(41009)

Hoseclamp2

Hose1

Connector

Installtheteettingandadapter

assembly.

Hoseclamp2

Straighttting

O-ring

Ballvalve1

Installthein-linehoseassembly.

Chip

Decal1

Installthechip.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (4 pages)

PAGE 1
Form No. 3370-544 Rev A Pro Control™ Spray System Upgrade Kit 2009 and Before Multi-Pro® 5600/5700 Turf Sprayer Model No. 41008—Serial No. 312000001 and Up Model No. 41009—Serial No. 312000001 and Up Installation Instructions Installation Loose Parts Use the chart below to verify that all parts have been shipped.
PAGE 2
1 1 Installing the Agitation Nozzle Assembly Parts needed for this procedure: 2 Nipple 1 Tee fitting 2 Elbow 1 Agitation nozzle 1 Nut g016997 2 Figure 2 Tank shown from the left 1. Front of unit 2 Procedure 1. Remove the nut and nozzle from the agitation nozzle assembly. Retain them for later use. Installing the Tee Fitting and Adapter Assembly 2. Attach a nipple to each end of the tee fitting (Figure 1). Parts needed for this procedure: G016799 1 1 2 2 3 4 4 5 2.
PAGE 3
2 3 4 1 5 6 7 8 2 1 g016968 Figure 4 G016800 Figure 3 1. Fork 5. 90 degree hosebarb 2. Straight hosebarb 6. Hose clamp 3. Tee 7. Adaptor 4. Connector 8. Hose 1. Hosebarb 2. Hose clamp 7. For 41009: Install the agitation valve assembly in the indicated location using the bolts already on the sprayer (Figure 5), then attach the kit hose, agitation hose, and supply hose to the assembly and secure it with a hose clamp. 2. Secure each hosebarb to the tee using a fork (Figure 3). 3.
PAGE 4
3 4 Installing the In-Line Hose Assembly Installing the Chip Parts needed for this procedure: Parts needed for this procedure: 1 Chip 1 Decal 2 Hose clamp 2 Straight fitting 2 O-ring Procedure 1 Ball valve 1. Remove the screws securing the console panel and remove the panel. Procedure 2. Remove the current chip and insert the new chip using the tool provided. Refer to instructions provided with the removal tool for the proper procedure (Figure 7). 1.