FORM NQ. 42055 MODEL NO. 41120, 41121, SET-UPLAND 41020, 41021 and 41122 PARTS LIST STANDARD SPRAY SYSTEM FOR USE ON THE MULTI-PRO 1100 VEHICLE Refer to the illustrated Parts List for the details of parts used in assembling the STANDARD Sprayer System. *Right" and "Left™ as used in the following instructions, refer to the operator’s right and left when seated in the normal operating position. Likewise, “Front® and “Rear® as seen from the operator’s position.
CENTRIFUGAL PUMP {continued) ¥ Install the Pump Belt Cover onto the Pump Cover Clamp and secure with two lock nuts. W Insert the 3/8" x 4" cap screw into the hole in the Pump Cable’s end fitting and through the Pump Cover. Recurs the Cable to the Pump Cover with a lock nut., W Attach the other end of the Pump Cable onto the Pin in the Pump Control Handle, Secure with a flat washer and hair pin cotter, Attach the Spring. W Engage the Pump Engagement Lever...DO NOT START THE ENGINE.
BOOM ASSEMBLY: Use a paint brush to apply a heavy coating of grease to the tubes which are to be inserted into the Vehicle Frame. ® Install the two Boom Mount Assembly into the Vehicle Frame as shown in FIG. 6. Use & tongue wrench to tighten the long {1/4" x 8"} screws which join the Wedges to the tubes. Tighten to 50 ft. lbs. CAUTION! FAILURE TO TIGHTEN THESE SCREWS SECURELY COULD RESULT IN THE BOOM FRAME FALLING OFF THE VEHICLE! THESE INSTRUCTIONS APPLY TO THE ASSEMBLY OF THE MANUAL BOOM ONLY, IF.
® Insert an Extension Boom Pipe into the pivot Assembly and secure with four 1/4" % hex hd cap screws and lock nuts. See FIG. 8. Repeat on the opposite side to assemble the other Extension Boom. m Attach the Boom Support Assembly to the Pivot Assembly, using a 5/16% x screw and hex nut. See FIG. 8. Secure the two plates of the Boom Support assembly to the Extension Boom Pipe, using two U-bolts and four lock nuts. ® Assemble the Boom Support Assembly to the other Extension Boom Pipe.
TANK REF PART NO. DESCRIPTION QY 1 42983 Hold-In Brace Says 2 2 22-12-AGED Hex Nut, 5/16 NC & 3 24-10-DB Flat Washer, 5/16 v.uvseuevoansassoarsrcsoocsnoaes & 4 42880 Mounting Band (Front) c.ceveecvaccvsoonsainns . 2 5 5125 U-Bolt, 1/4 NC 4 6 42198 Rubber Hold Down Strap . 2 7 42259 Boom Hold-In Says. -~ L.H. heartrending e 1 8 25-25-2ND Carriage Bolt, 5/16 NC X 3/4 viverevuneenocennoeas & Q 22-11-AGED Hex Nut, 1/4 NC avecanesenncenrranocensoens 8 10 42316 Boom Hold-In Ayes. R.H. ..
BOOM FRAME A CAUTION! THE TWO SPRINGS (REF. #24) ARE UNDER APPROX. 150 LBS, OF PRESSURE. BE VERY CAUTIOUS WHEN REMOVING THE SPRING PINS (REF. #26) FOR REMOVAL OF THE SPRINGS. MUST BE TORQUED TO 50 FT. LBS. A CAUTION! THE TWO BOLTS (REF.
PUMP DESCRIPTION QTY 1 41307 $0°g8t. Elbow, 1" NPT . 2 41306 Reducer Bushing, 1" x 1/2% FPT . 3 41314 Close Nipple, 1/2" NPT 4 40192 Ball valve, 1/2" NPT 40486 Wiki Raptor x 1" MPT 41317 Couple Dust Cap 6 41305 Tee, 1" NPT v 7 41304 Close Nipple, 1% NPT vecvevvvennaen 8 40479 Wiki Raptor, 1% MPT «nonsensitive g 9773 Square Key annexations 10 99226 Centrifugal Pump 11 41315 Hex Plug, i" NPT casvicrsraun e anon, 12 9987 Close Nipple, NPT .overenthusiastic 13 42701 Suction Strainer ,..u.s.
CONTROL VALVE & BOOMS REF PART NO. DESCRIPTION QrY i 40480 Wiki Adapter x 1 H.B. 2 2 21146 Hose CLAMS .u.vevvverooussnrnmsansooan 4 3 42954 Supply Hose, 1" I.D. x 53" 1 4 41730 Hose Barb, 3/4% MPT % 1" HuB. 2 5 42939 45 St. Widow, 3/4" NPT tuveenmrunnroannsacnsnnns 2z & 24-10-BDRM Flat Wash ex, 5/16 S.A.E. .. 11 7 20-26-GAD H.H.C.8.
REF PART NO. DESCRIPTION Qry 1 42125 Jam Nut, Nickel Plated Cerulean chasten 1 2 42126 Screw, Stainless Steel .. 2 3 42127 Col Ll COVER wevsrvanemuwesnns Caravan 1 4 42128 Armature Stop, Nickel Plated vv..ivevveneionns 1 5 42129 12 V. coil says, Nylon Encapsulated «siesta. 1 € 42130 Strap, Steel-Epoxy Painted resentment 1 7 42131 Upper Diaphragm Housing, Nickel Plated 1 8 EHH spring, Stainless Steel (f/w 42942 Rit) 1 9 42132 Armature, Nickel Plated ...iveevvuneannas 1 10 42133 Retainer RING .