MODEL NO. 41120-50001 & UP MODEL NO. 41128-50001 & UP MODEL NO. 41020-50001 & UP MODEL NO. 41021-50001 & UP MODEL NO. 41130-50001 & UP FORM NO. 93-1049 SET-UP AND PARTS CATALOG FOR THE MULTI-PRO 1100™ VEHICLE L PRO-CONTROL™ SPRAY SYSTEM J Refer to the illustrated Parts List for the details of parts used in assembling the Pro-Control™ System. NOTE: "Right", "Left", "Front” and “Rear” are referenced while seated in the operator's position. CONSOLE COMPUTER: 1.
CONSOLE COMPUTER (Cont'd.} 11. Connect the push-on terminal on the red wire to the male terminal on the red wire coming from the Fuse Block. 12. Insert the 20-amp Fuse into the Fuse Block receptacle. NOTE: The remaining Wiring Harness connections will be made after the Tank and Saddle and the Boom Frame are installed on the Vehicle. SPEED SENSOR: 1. Mount the four (4) Wheel Magnets to the inside rim of the Vehicle's left rear wheel with eight (8} hex nuts and four (4) lock washers as shown in FiG. 3.
1. Pivot Mounting Plate 3. Clevis Pin 2. Pump Pivot Plate 4. Hair Pin Cotter 2. Align the pivot tubes on the Pump Pivot Plate with those on the Pivot Mounting Plate. Insert the tw% (2) clevis pins and secure with two (2) hairpin cotters. NOTE: In the following instructions, “sealer” refers to RTV clear silicone. 3. Secure the Centrifugal Pump in a vise. ly thread sealer and install the fittings to connect the Suction, Suppl, Agitator and Overflow Hoses to the Pump as shown in FIG. 5. 1. Suction 4.
CENTRIFUGAL PUMP (CONT'D): If Step 13 does not achieve the necessary tension on the Control Cable, loosen the Pump mounting bolts and side the Pump on the Pivot Plate to move it away from the Vehicle Frame, increasing the Cabin tension. TANK ASSEMBLY: 1. Cut the shipping straps and remove the Spray Tank and Saddle Assembly from the shipping skid. NOTE: In-the-following -instructions; -sealer refers to RTV clear silicone when used for pipe fittings. 7 3. Elbow & Hose Barb (Overflow) 4. Mounting Member FIG.
FLOW METER (Cont'd): 2. Slide a hose barb info the other end of the Adapter Hose and secure with a hose clamp. 3. Apply thread sealer and attach the 1" male quick couplet to the hose barb's threaded end. 4. Secure the Flow Meter to the Mounting Bracket with the two (2) hose clamps furnished. 5. Connect the x 18" Supply Hose between the barb on the inlet end of the Flow Meter and the hose barb in the tee at the Pump. Secure with two (2) hose clamps. 8.
BOOM FRAME (Cont'd): 8. Loosely attach the triple barb Nozzle Assembly in the approximate censer of the Center Boom Pipe. For the most uniform spray coverage, position all Nozzle Assemblies at a 45° angle as shown in FIG. 10, Tighten clamp screw to secure the Nozzle to the Boom Pipe. 9. Loosely attach a single barb Nozzle Assembly to each end of the Center Boom Pipe. Place two hose clamps on the two 3/4" x 18" Jumper Hoses and connect the single barb Nozzles to the triple barb Nozzle.
1. Control Ave 8. Solenoid Mg, Strap 2. Solenoid Says, 7. Pressure Gauge 3. Control Naive Bret. 8. Barbed Elbow 4, Cross Support Angle 9. Boom Feeder Hose 5. Flow Meter Hose 5. Slide the Solenoid Mounting Strap info position and mount the complete Control Valve and Solenoid Assembly to the Cross Support as shown in FIG. 13. Use four 5/18" x 1" hex hd cap screws with four washers placed below the screw heads, two between the strap and the Cross Support and four below the Cross Support under the nuts. 6.
PRO-CONTROL. TANK (MULTI-PRO 1100) Ref | Part No. Description Qty Ref | Part No. Description Qty| 1 42083 Hold-In Brace Assembly 2] 26 43066 Bulk Head, 2° NPT 1 2 [R2-12-AJD Hex Nut, 5/16 NC B 7 141800 [Tank Fitting, 1" NPT (/w Tank Says} | 1 3 [24-10-DB Flat Washer, 5/16 4 B 41307 90° 8t, Elbow, 1 NPT 1 4 092.
BOOM FRAME (MULTI-PRO 1100) A CAUTION! THE TWO SPRINGS (REF. #24) ARE UNDER APPROX. 150 LBS. OF PRESSURE. BE VERY CAUTIOUS WHEN REMOVING THE SPRING PINS (REF. #26) FOR REMOVAL OF THE SPRINGS. A REF., #8) LBS.
BOOM FRAME (MULTI-PRO 1100) Ref] Part No, Description oty | [ Rel Portia. Description aty i 42228 Tube Exigence Says 2] | Rial Washer, 7" SAE.
CENTRIFUGAL PUMP & FLOW METER (MULTI-PRO 1100) Ret | Part No. Description sooty [Ret | Part No. Description oty 1 [41307 [90° St.
MOTORIZED CONTROL VALVE & BOOMS (PRO--CONTROL™) Ret! Part No. Description Qty | Hef] Part No. | Description Oty 1]40485 Pressure Gage 1 24 1920355 Electric Solenoid Valve (100 F.8.
Park No. Description Qty Ref| Part No. Ascription 42722 Power Switch 1 i? Fuselage 15 1 42723 Ale 1/ Rate 2/ Man. Switch 1 13 162-8687 Console Contort Cable (13 11) 1 42724 Man. Adj.
FLOW METER (41482) CONTROL VALVE (41480) Aet] Part No. Description Qty Ref| Part No. Description Oty 1142475 Sensor Housing 1 1142318 Naive Cover 1 2142476 #10-32x 3/4 Screw (St Steel) 12 2 {42482 #6-20x 3/4 Thread Forming Screw 8 3 42488 O-F Ring (Vito) 1 342483 Motor Says 1 4142477 Transducer Says.
SAFETY AND INSTRUCTION DECALS CHEMICALS CAN BE HAZARDOUS TO REDUCE THE RISK OF ENVIRONMENTAL DAMAGE AND PERSONAL INJURY: ® SELECT THE CORRECT CHEMICAL FOR THE AT ® HANDLE AND APTLY CHEMICALS AS WEAR PROTECTIVE CLOTHING AND MASK, RN WASH CONTAINER Part No. 83-0688: Located on Lid of Sprayer Tank. FILL WITH CLEAN FRESH WATER ONLY. Part No. 93-0800: Located aside of Clean Water Wash Tank Saddle.