FORM NO. 82-0377 Rev. A OPERATOR'S, SET-UP & PARTS MANUAL TOR | | SPRAY GUN KIT . For the MULTI-PRO® and WORKMAN?® Vehicles To assure maximum safely, optimum A The safety alert symbol means CAUTION, performance, and to gain knowledge of the WARNING, or DANGER personal safety product, it is essential that you or any other instruction. Failure to comply with the operator of this equipment read and instruction may result in personal injury.
SAFETY INSTRUCTIONS 6. DO NOT leave equipment under pressure unattended at any time. Relieve line pressure by shutting off power to pump, turning off the liquid supply 1o the pump, and actuating trigger until all fluid ceases to flow; then position trigger lock to the “locked off” position. 7. DO NOT eave spray gun with trigger in the “locked on” position after the pump has been turned off. 8. DO NOT use damaged, perforated, or weakened fluid hose. 9. DO NOT use a spray gun with a damaged trigger lock. 10.
SET-UP INSTRUCTIONS “Right” and “Left” as used in the following instructions, refer to the operator’s right and left when seated in the normal operating position. Likewise, "Front” and “Rear” as seen from the operator's position. 1. Remove the rubber protective cap from the carriage bolt which protrudes from the left rear Tank Band. See FIG. 1. FiG. t 1. Left Rear Tank Band 2. HBase Hook 2, Attach the Hose Hook to the bolt and secure it with the 5/16" hex nut and a flat washer. 3.
SPRAY GUN KIT 41022 Ref| Part No. Description Qty [Ret | Part No. Description Qly 1 93-6240 [Cap, Aluminum 1 i 3-6257 Spring Guide Washer, St Steel 1 R 938268 [Orifice Duse, Hardened St. Steel 1 20 [B-6258 Main Spring, Stainless Steel 1 i3 1935241 Nozzle Housing, Aluminum 1 21 [93-6259 Handle Body, Aluminum 1 M 93-8242 Guide Vane, Aluminum 1 22 3-8260 Rivet, Steel-Zinc Plated 2| 5 193-6243 i Gasket, Aluminum 2 23 [93-6261 [Trigger, Steel-Nickel Plated 1 B [p-8248 [Tubing, Aluminum 1 24 193.
MAINTENANCE A warning Fluids under high pressure can penetrate skin and can cause severe injury, possibly resulting in amputation or death, Hot liquids and chemicals can also cause burns or injury. ® Disengage the Spray Pump (using the Pump Switch) to remove pressure before proceeding to step 1. ® DO NOT at any time place hand or any other part of the bad in front of spray nozzle or tip.
MAINTENANCE 6. While holding packing screw carefully screw inlet body over packing to engage threads on packing screw. Tighten finger tight only. 7. Tighten stem nut fully on stern with undercut side of stem nut facing away from inlet body. 8. Install new washer on new trigger guide followed by new trigger stop spring. Thread trigger guide on stem until end of stem is flush with the inner edge of trigger guide then back off two turns and use wrench to tighten against stet rut.
PRODUCT CHANGES In an effort to make improvements available to TOR owners as quickly as possible, minor changes are incorporated anti Toto's Products from time to time that da not become immediately shown in the Parts Catalog.
The Toto Promise A One Year Limited Warranty The Toto Company promises fo repair your Model 41022 Spray Gun Kit if defective in materials or workmanship. The following time periods from the date of purchase apply special warranty terms, on certain components, may be offered through The Torah Company by the component manufacturers: Commercial Products The cost of parts, labor and transportation are included, If you feel your TOR Product is defective and wish-{o rely on The Toto Promise, the following.
