Operator's Manual

13
BEFORE SPRAYING
NOTE: RATE 2 should not differ more than 20%
from RATE 1, or Spray Pattern may suffer. If
you do not use a second rate, enter the same
rate in both RATE 1 and RATE 2.
YOU HAVE NOW COMPLETED
PROGRAMMING THE CONSOLE. The flashing
"CAL" will now extinguish. If not, repeat
procedure starting at step 5.
INITIAL CONSOLE PROGRAMMING:
You may also want to enter data in the keys
labeled:
VOL
TANK
and
TIME
0
although it is not required for
operation of the system.
13. Key 9 "VOLUME TANK" (Optional) - Enter
the amount of material in the Tank. This number
must be re-entered each time the Tank is refilled.
The function monitors Tank Volume while spraying,
based on the total amount applied.
14. Key 0 "TIME" (Optional) - Enter time of day
based on 24 hours (i.e. 1:30 p.m. is 13:30), or
enter "0" to measure elapsed time. To set Date,
press
TIME
0
, And "Month" appears; press
ENTER
to
change month. Set DAY by pressing
TIME
0
until "DAY"
appears; press
ENTER
to change DAY. Set YEAR by
pressing
TIME
0
until "YEAR" appears; press
ENTER
to
change year. Press
TIME
0
again to set POWER
DOWN day. See Page 10 for Power Down
instructions.
OTHER DISPLAY FEATURES:
1. To display TOTAL AREA covered, momentarily
depress key labeled:
TOTAL
AREA
To "zero out" this total at any time, enter a "0" in
this key.
2. To display TOTAL VOLUME sprayed,
momentarily depress key labeled:
TOTAL
VOLUME
To "zero out" this total at any time, enter a "0" in
this key.
3. To display FIELD AREA covered, momentarily
depress key labeled:
FIELD
AREA
To "zero out" this total at any time, enter a "0") in
this key.
4. To display FIELD VOLUME sprayed,
momentarily depress key labeled:
FIELD
VOLUME
To "zero out" this total at any time, enter a "0" in
this key.
5. To display DISTANCE (feet [m] traveled),
momentarily depress key labeled:
DISTANCE
To "zero out" this total at any time, enter a "0" in
this key.
6. To display MPH (km/h), momentarily depress
key labeled:
SPEED
7. To display VOL/MIN (volume per minute) being
sprayed at speed being traveled, momentarily
depress key labeled:
VOL/
MIN
8. To display AREA/HOUR (area per hour)
momentarily depress the key labeled:
AREA/
HOUR
This is an actual calibration of the area per hour at
the present speed you are traveling. It is not an
average over time.
9. To display US, TI or TU and SP1, SP2 or SP3
selections, depress and hold
SELF
TEST
ç
. These
selections will be alternately displayed.
10. The Data Menu button is used when additional
devices are attached like a data logger or GPS.
(See manuals for additional devices for
programming.) Other values for PWM should not
be changed; they are preset for this system.
SELF TEST FEATURE
SELF TEST allows speed simulation for testing the
system while the vehicle is not moving. Enter the
simulated operating speed in the key labeled:
SELF
TEST
ç
If 4 MPH (6.4 km/h) is desired, enter 4.0 (6.4).
Verify speed by depressing key labeled:
SPEED
4.0 (6.4) will appear in the DATA display.
The SELF TEST speed will clear itself when motion
of vehicle is detected by the Speed Sensor. A
SPEED CAL value of 148; the number calculated
from page 4.
THE FEATURES LISTED BELOW ARE NOT
NECESSARY FOR THE OPERATION OF THE
PRO-CONTROL SYSTEM, BUT ARE
INCLUDED AND CAN BE ACCESSED AT THE
OPERATOR'S OPTION.
SEQUENCE TO ACTIVATE DATA-LOCK (This
is an optional feature which prohibits the entry
of data without first entering the DATA LOCK
CODE).
1. Depress
DA TA
MENU
several times until "Press Enter for
Data Lock" is displayed. Press "Enter" and Display
will show New Code E.
2. Enter 4 digit code within 15 seconds.
EXAMPLE: For 1058 depress:
BOOM1
CAL
1
TIME
0
METER
CAL
5
RATE2
CAL
8
and
ENTER
.