Operator's Manual

ManualsBrandsToro ManualsAttachmentsSonic Boom Kit, Multi-Pro Turf Sprayers

©The TORO Company - 2002

To assure maximum safety, optimum

performance, and to gain knowledge of the

product, it is essential that you or any other

operator of this equipment read and

understand the contents of this manual before

the vehicle engine is ever started. Pay

particular attention to the SAFETY

INSTRUCTIONS highlighted by the triangular

safety alert symbol.

The safety alert symbol means CAUTION,

WARNING or DANGERpersonal safety

instruction. Failure to comply with the

instruction may result in personal injury.

BEFORE OPERATING:

1. Operate this accessory only after reading

and understanding the contents of this manual.

A replacement manual is available by sending

complete model and serial number to: The Toro

Company, 8111 Lyndale Ave. So., Bloomington,

MN 55420-1196.

2. Learn how to operate the Sonic Boom and

how to use the controls properly. DO NOT let

anyone operate this equipment without first

receiving thorough instructions.

3. Keep all shields, safety devices and decals in

place. If a shield, safety device or decal is

malfunctioning, illegible or damaged, repair or

replace it before operating the machine.

4. Chemicals can injure persons, animals,

plants, soils or other property. To eliminate

environmental damage and personal injury:

MODEL NO. 41089

OPERATORS

MANUAL

FORM NO. 106-1224

SONIC BOOM

SAFETY INSTRUCTIONS

Keep this Operators Manual in the plastic tube behind the operator seat.

It is very important that all persons operating this equipment have easy access to these instructions at

all times.

Carefully read and follow the Installation Instructions that are provided with this equipment and the

Safety Instructions in the Vehicle Operators Manual.

This safety-alert symbol is used to call attention to a dangerous situation, which could result in

serious injury or death to the operator or a bystander.

Safety, mechanical and some general information in this manual are emphasized. DANGER,

WARNING and CAUTION identify safety messages. Whenever the triangular safety symbol appears,

it is followed by a safety message that must be read and understood. For more details concerning

safety, read the Safety Instructions that follow. IMPORTANT identifies special mechanical information

and NOTE identifies general information worthy of special attention.

These instructions are provided as a guide for the safe operation and maintenance of this equipment.

However, the operators personal safety, as well as those persons in the work area, will depend on the

careful actions and good judgement of the operator.

To reduce the potential for injury or death, comply with the following safety instructions.

A. Select the proper chemical for the job.

B. Follow manufacturers instructions on

chemical container labels. Apply and handle

chemicals as recommended.

C. Handle and apply chemicals with care.

Wear goggles and other necessary protective

equipment. Handle chemicals in well ventilated

areas. Never smoke while handling chemicals.

D. Properly dispose of chemical container

and unused chemicals.

5. Make certain everyone is clear of the machine

before starting the engine.

6. If equipment begins to vibrate abnormally,

stop immediately. Shut off the vehicle engine

and disengage all power. Repair all damage

before commencing operation.

for the WORKMAN

and MULTI PRO

SPRAYERS

Summary of content (8 pages)

PAGE 1
FORM NO. 106-1224 OPERATORS MANUAL MODEL NO. 41089 SONIC BOOM for the WORKMAN® and MULTI PRO® SPRAYERS To assure maximum safety, optimum performance, and to gain knowledge of the product, it is essential that you or any other operator of this equipment read and understand the contents of this manual before the vehicle engine is ever started. Pay particular attention to the SAFETY INSTRUCTIONS highlighted by the triangular safety alert symbol.
PAGE 2
SAFETY INSTRUCTIONS AND DECALS A. Stop the vehicle and set the parking brake. CAUTION This accessory will raise the Booms during operation, adding to the overhead clearance needed to operate the vehicle safely. In order to avoid electric shock, inspect the area overhead for wire before raising Booms. Always use caution while operating the Booms near low clearance areas. WHILE OPERATING: 7. Before servicing or making any adjustments to the Sonic Boom: B.
PAGE 3
CONTROLS 1. Sonic Boom Mode Switch: Toggles the boom lift control between off, automatic operation, and manual operation. 2. Left Boom UP/DOWN Switch: Controls the up and down motion of the Left Boom. 3. Right Boom UP/DOWN Switch: Controls the up and down motion of the Right Boom. Sonar Indicator Light: Located on Front Instrument Panel (Dash). Remains on when system is functioning correctly in Auto or Manual mode.
PAGE 4
OPERATION AUTOMATIC (SONAR) OPERATION: Before using the boom in automatic operation, the controller must be calibrated to return the Booms to a level position. This is a onetime step that stores a reading into the memory of the controller and should not have to be repeated unless service is performed on the controller, or Boom height is changed. Controller Calibration: 1.
PAGE 5
TROUBLESHOOTING Trouble shooting of the Sonic Boom can be done with or without the Diagnostic ACE display tool. A problem is identified by observation of incorrect response of the system. The schematic diagram should be reviewed to understand the electrical circuit. Using the Diagnostic ACE display tool for troubleshooting: The following steps should be followed to setup and use the Diagnostic ACE display: 1. Turn off the Sonic Boom power by placing the SONIC BOOM MODE switch to the OFF position. 2.
PAGE 6
TROUBLESHOOTING (CONT'D) 2. If indicator Light flashes after repeated manual correction of the error condition, the problem may be at the Sensor. A. Ensure that the Sensor Filter is clean. B. Verify that the Sensor has power applied. If the Sensor is powered, the LED at the end of Sensor will be flashing, and the Sensor will be making a ticking sound. C. Verify that Sensor output is functioning. This can be done by swapping Boom Sensor to see if the problem follows the Sensors.
PAGE 7
1358
PAGE 8
The Toro General Commercial Products Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your 1996 or newer Toro Commercial Product (Product) purchased after January 1, 1997, to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first.