Operator's Manual

ManualsBrandsToro ManualsAttachmentsSonic Boom Kit, Multi-Pro Turf Sprayers

 2003 by The Toro Company

8111 Lyndale Avenue South

Bloomington, MN 55420-1196

Printed in the USA

Original Instructions (EN)

Sonic Boom



Kit

for Multi Pro



1200, 1250, and 5600 Turf Sprayers

Model No. 41089—Serial No. 230000001 and Up

Form No. 3329-751 Rev A

Installation Instructions

Important To use this kit, you must also have the electric boom lift kit, available from your Authorized Toro Distributor.

Note: Determine the left, right, front, and rear sides of the machine while seated in the normal operating position.

Note: If you are installing this kit on a vehicle equipped with an enclosed boom system, use these instructions along with the

enclosed boom system instructions.

Description Qty. Use

Ultrasonic sensor

U-bolt

Washer, 5/16 inch

Locknut, 1/4 inch

Corrugated tube

Cable ties

Install the ultrasonic sensors.

Electronic control unit (ECU)

Mount plate

Relay

Bolt, 1/4 x 5/8 inch

Lock washer, 1/4 inch

Nut, 1/4 inch

Wiring harness

Screw, #10

Nut, #10

Bolt, 1/4 x 2-1/2 inches

Bolt, 5/16 x 3/4 inch

Lock washer, 5/16 inch

Install the ECU.

Light assembly

Decal, 94-8582

Install the light.

Switch

Fuse, 30 amp

Cable ties

Install the controls.

Decal, 94-8604 1

Save for diagnostic use by your Authorized

Toro Distributor.

Summary of content (8 pages)

PAGE 1
Sonic Boom for Multi Pro Form No. 3329-751 Rev A Kit 1200, 1250, and 5600 Turf Sprayers Model No. 41089—Serial No. 230000001 and Up Installation Instructions Important To use this kit, you must also have the electric boom lift kit, available from your Authorized Toro Distributor. Note: Determine the left, right, front, and rear sides of the machine while seated in the normal operating position.
PAGE 2
Setup If you do not have the electric boom lift kit installed, install the actuators before installing this kit, but do not install the wiring harness or switches for the electric boom lift kit. If you have already installed the complete electric boom lift kit, disconnect the wiring harness from the actuators and vehicle, and remove and discard it.
PAGE 3
. Secure the ECU to the mount plate (Fig. 4), using 4 bolts (1/4 x 2-1/2 inches), 4 lock washers (1/4 inch), and 4 nuts (1/4 inch). 1 6 1 2 3 m–6787 7 Figure 6 8 4 3 2 1. Mount plate 2. Vehicle frame 5 Mount plate ECU Bolt, 1/4 x 2-1/2 inches Lock washer, 1/4 inch 5. 6. 7. 8. 3. Bolt, 5/16 x 3/4 inch 4. Lock washer, 5/16 inch 5. Ensure that the 3, 10-amp fuses and 1, 5-amp fuse are installed in the fuse block on the mount plate as illustrated in Figure 3. m–6790 Figure 4 1. 2. 3. 4. 4 6.
PAGE 4
2 1 4 2 1 3 3 m–6795 Figure 9 1. Plug 2. Switch 4 m–6792 3. Notch (at back) 4. Spray control panel Figure 8 1. Decal 94-8582 2. Light 3. Washer 4. Nut 2. Remove the nut and washer from the bottom of the light. 2 3. Install the light in the dash and secure it using the washer and nut (Fig. 7 or 8). 1 4. Connect the 2 spade connectors on a separate branch of the wiring harness to the posts on the light. m–6458 Installing the Controls on a Multi Pro 1200 or 1250 Turf Sprayer Figure 10 1.
PAGE 5
Connecting the Wiring to the Fuse Block 3 1. Route the branch of the wiring harness with the small spade connector and a ring or fork terminal into the seat box and to the fuse area. 4 1 2. Connect the ring or fork terminal on the black wire to the ground terminal block (Fig. 11). 5 2 4 2 m–6796 Figure 12 1 1. Spray control panel 2. Latch 3. Switch 5 4. Plug 5. Notch 3 2.
PAGE 6
Connecting the Wiring to the Fuse Block 4. Secure the wiring harness to the boom frame using cable ties as needed. 1. Route the branch of the wiring harness with the small spade connector and a ring or fork terminal into the seat box and to the fuse area. Calibrating the Sonic Booms 2. Connect the ring or fork terminal on the black wire to the ground terminal block (Fig. 13). 4 1.
PAGE 7
Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 94-8582 94-8576 94-8604 Operation Using the Controls You can temporarily override the automatic operation of the booms using the boom switches to raise or lower one or both booms.
PAGE 8
• Manual—turns off the automatic adjustment of the booms and enables the boom switches. • On—the sonic boom system is on and operating normally • Flashing quickly—calibration mode • Flashing slowly—system error; refer to Troubleshooting, page 8. Maintenance Clean the sensors periodically with a damp cloth. When you clean the sensors, inspect the foam sensor filter. If it is damaged or excessively dirty, replace it. Figure 14 1. Sonic Boom switch decal 2.