FORM NO. 92-0258 MODEL NO. 41410-30001 & UP MODEL NO. 41020-30001 & UP MODEL NO. 41120-30001 & UP MODEL NO, 41021-30001 & UP SET-UP AND W PARTS CATALOG TOR} SKID SPRAYER ] SAFETY INSTRUCTIONS TIP OVER OF TRANSPORT VEHICLE CAN CAUSE SERIOUS INJURY OR DEATH. USE OF THIS SKID SPRAYER ON SOME TRANSPORT VEHICLES CAN CAUSE THE VEHICLE TO BECOME UNSTABLE. USE EXTREME CAUTION ON HILLS AND SLOPES, READ AND UNDERSTAND THE SAFETY INSTRUCTIONS BEFORE OPERATING THIS MACHINE.
3. Apply thread sealer and install the 90° barbed elbow into the bottom of the Tank. See FIG. 2. IMPORTANT! Position the barbed elbow as shown, so that it will angle toward the High Pressure Pump, after the Tank is installed on the Skid Frame. 4. Apply thread sealer and assemble the 90° &t elbow to the male Quick Couplet. Install the elbow into the fitting at the spill-way end of the Tank, so that it angles toward the outside of the Tank as shown in FIG. 2.
Install the Main Frame Tube so the nozzles are 22 to 32 inches above the ground. 1. Position the Cross Support Angle and attach it to the Boom Mount Assemblies with two 1/2" x hex hd cap screws, and lock nuts, 2. Position the Spacer Tubes between the Boom Mount uprights and the lugs on the Main Frame Tube. Use two 1/2'x 4" hex hd cap screws and lock nuts to secure the Main Frame Tube to the uprights. See FIG. 8. 7. Loosely attach a single barb Nozzle Assembly to each end of the Center Boom Pipe.
2. Loosely attach the Control Valve Bracket to the Cross Support with a 5/16° x 3/4° cap screw, flat washer and nut. See FIG. 8. 1. Control Naive 6. Solenoid Mtg, Strap 2. Solenoid Says, 7. Overflow Hose 3. Control Naive Brit 8, Gauge Tube Fitting 4. Cross Support Angle 9. Boom Feeder Hose 5, Supply Hose 8. Slide the Solenoid Mounting Strap into position and mount the complete Control Valve and Solenoid Assembly to the Cross Support as shown in FIG. 8.
PUMP SYSTEM: FOR HIGH PRESSURE SPRAYING (i.e. Hand A WARNING Gun Spraying) use the Diaphragm Pump System. Install the Drive Belt on the Engine and Diaphragm Pump Pulleys as shown in FIG. 10. OPERATING THE SKID SPRAYER WITHOUT SAFETY SHIELDS IN PLACE CAN CAUSE PERSONAL INJURY. HAVE ALL SAFETY SHIELDS IN PLACE BEFORE OPERATION! FAILURE TO USE THE PROPER HIGH PRESSURE EQUIPMENT CAN CAUSE PERSONAL INJURY. Determine which of the two Pump systems you NEVER.
INSTALLING THE SKID SPRAYER ON A TRANSPORT VEHICLE: Make sure that the weight of the Skid Sprayer and any optional equipment that may be added, is within the weight capacity of your transport vehicle. See the chart below for the weights of this unit and it's optional equipment. Skid Sprayer (Full Tank) 1,973 Ibs, Foam Marker 30 |bs. Electric Boom . 2B 1bs, Manual Hose Reel 150 Ibs. 1. Position the Skid Sprayer with it's Tank as far forward toward the operator's position as possible. . 2.
FINDING THE CORRECT NOZZLE Size GPM. =_ GPA xM W Example: 81 GPM = 80 GPA x 3 MPH x 20° {Per Nozzle} 5040 *W = Nozzle spacing in inches.
TANK REF. PART NO. DESCRIPTION QrY. 1 42983 Hold~In Brace SAYS «.eerrvnvnvnvncnsnn 2 2 22-12-AGED Hex Nut, 5/16 NC 6 3 Flat Washer, 5/16 8 4 42880 Mounting Band (Front) 2 5 92-0010 U-Bolt, 1/4 NC . 4 6 42198 Rubber Hold Down Strap 2 7 42259 Boom Hold-In Says L.H. ...vevvausens 1 8 25-25-GAD Carriage Bolt, 5/16 NC x 3/4 6 9 22-11-AJFD Lock Nut, 1/4 NC cesarean 8 10 42316 Boom Hold=Tn Says RUSH. I 11 43013 Mounting Band (Rear) Caner e 2 12 40153 Hose HOOK ...cvniivnrinnnvennns e 1 13 42452 Protective Cap ..
BOOM FRAME A CAUTION! THE TWO SPRINGS (REF. #24) ARE UNDER APPROX. 150 LBS. OF PRESSURE. PINS (REF. #26) FOR REMOVAL OF. THE SPRINGS. A BE VERY CAUTIOUS WHEN REMOVING THE SPRING CAUTION! THE TWO BOLTS (REF. #8) MUST BE TORQUED TO 50 FT. LBS.
BOOM FRAME REF. PART NO, DESCRIPTION QTY. 1 42223 Tube Wedge SAYS e 2 2 22-15-AJFD Lock Nut, 1/2 NC 4 3 42225 Cross Support Angle 1 4 20-86-GAD HHS, 1/2 NC x 2 5 42258 Spacer Tube, 1g. 2 6 Boom MOURN SAYS 1 7 42217 Boom MOUNT SAYS s 1 8 42199 HHS, i.vuniinvveninnonnn 2 9 42234 Center Boom Angle ..uv.iiuveeenovainnenan 2 10 Flat Washer, 5/16 ueuscnenoscnriocnsnn 4 11 22-12-AGED Hex Nut, 5716 NC vviuiniinuninnrianans 8 12 20-47-GAD HHS, 2 13 24-11-AD Flat Washer, 3/8 heaves 2 14 40493 Center Boom Pipe ..
CONTROL VALVE & BOOMS REF. PART SOON AU W OOH 40480 21146 920244 41730 42939 24-10-DB 20-26-GAD 42936 42938 41325 41294 42872 41313 92-0045 42944 41257 42940 42941 41340 42274 42870 42871 42942 41310 92-3707 40493 40506 42282 40444 40223 41088 42828 92-3977 40998 40997 40998 41001 41002 41000 41003 DESCRIPTION Wiki Adapter ivuowsoarinonen Hose Clamp . Supply Hose, 1" I.D. x 80" e Hose Barb, 3/4* MPT x 1" H.B., .. washtubs 45 St. Elbow, 3/4" NPT ...i.vinnsiasas Plat Washer, 5/16 S.A.B.
SKID FRAME REF. PART NO. DESCRIPTION QTY. 1 92-0213 Belt Guard SAYS ...vvivnessinansnvaononan, 1 2 92-0218 Belt Shield subterranean 1 3 34-140 AMID Hex Washer Hd Self-Tap Screw, 1/4 NC x 5/8" 11 4 42559 Manual Storage Tu Be ...iieerivveciiinsnane 1 5 42560 Storage Tube Bracket 2 6 20-47-GAD HHS, iviiveniroannanneann, 10 7 24-11-AD Flat Washer, 3/8 crevasse 1B 8 HHS, 3/8 NC x 1-374" .iiviirierenran. & 9 92-0049 Square Key, 3/16 x .. 1 10 41390 Engine Pulley . .uneensncocnssonsnsenersrse.
PUMP SYSTEM REF. PART NO. DESCRIPTION QTY. 1 92-0337 Hand Gun High Pressure 1 2 920353 Hose Says Hand Gun (25 Ft Hi-PSI) .. 1 3 82-0230 Pump Control Unit uiiiuninreinenan 1 4 92-0220 Diaphragm PUMP .v.uviinenvevronnsoaras 1 5 21146 Hose Clamp, 1" HOSE ...vuwuvnvnoronsnn 4 6 92-0229 Gear Reduction Unit 1 7 92-0223 Extension Flange ASS'¥. ...evanescence 1 92-0228 Flange Bearing (f/w 92-0223 Says) 1 8 92-0049 Sq. Key, 3/16 x 3 3 41390 Pump Pulley = Diaphragm. . ...ascensions.
DIAPHRAGM PUMP (92-0220) REF. PART NO. DESCRIPTION QTY. 1 92-3531 Pump BOAT suvenvunrernonasananannsiaone 1 2 92-3532 Head Says (Right Hand) 1 3 92-3533 Head Says (Left Hand) . 1 4 92-3534 Nut (12 MA) 8 5 92-3535 Piston 2 6 92-3536 Connecting Rod 1 7 92-3537 Piston Sleeve 2 8 92-3538 Retainer Ring 2 9 92-3539 Connecting Rod Pin 2 10 92=3540 Retaining Ring 4 11 92-3541 Piston Ring 2 12 92-3542 Retaining Belt .
CENTRIFUGAL PUMP (97802) REF. PART KNO. DESCRIPTION QY. 1 27475 Volute 1 2 27489 O-Ring 1 3 27484 Cap Screw, 5/16 x 1/2 Stanley. Steel . 1 4 27485 Lock Washer, 5/16 Stainless Steel 1 5 27487 Flat Washer, 5/16 Stainless Steel 1 6§ 27478 Shaft Seal ...ovevvenucrnanonsnain 1 41740 Optional Heavy-Duty Seal 27482 Impeller vuvevvrrrnereaanato it nanny 1 8 27486 Square Key, 3/16 x 1/2 Stan. Steel 1 9 27476 Frame ..c.vcevecscronsons 1 10 27477 Shaft, Stainless Steel . 1 11 27483 Lock Ring ..oco.
PUMP CONTROL (92-0230) REF PART NO. DESCRIPTION QTY. 1 92-3574 Hose Barb . Creeeieresaaas 1 2 92~3575 Barb Nut 1 3 92-3576 O=RING cvvrenvrouranannsennseny 2 4 92-3577 Threaded Adapter 1 5 92-3578 Tension Spring Housing 1 6 92-3579 2 2 7 92-3580 Lever Guide 1 8 92-3581 Relief Valve Lever . 1 9 92-3582 Locking Clip P 1 10 92-3583 Pressure Adjustment Nut 1 11 92-3584 Threaded Guide Ve 1 12 92-3585 Tension Spring ...vevevvnercnrennn 1 13 923586 Tension Spring Retainer 1 14 923587 Relief Valve Body ...
REF. PART KO. DESCRIPTION QTY. 1 HEAL CASE (usvsesereraversornonnnaivans 1 2 92-35%4 Plug 4 3 9243595 Gasket 1 4 92-3596 Stud 4 5 92-3597 Hex Hd Bolt 92-3598 Bolt for .
SPRAYER CONTROL REF . PART NO. DESCRIPTION QTY. 1 42933 12-10 AWG Female Terminal 2 2 42934 16-14 AWG Female Terminal 1 3 42932 Insulated Female Terminal 3 4 42870 Solenoid Valve ..c.ccovvourennenuns 1 5 42936 Control Valve 1 6 42931 Male Fitting 1 7 42930 Tubing ..enviable. e 1 8 42935 72" Cable Says (Solenoid Hook-Up) @ 1 9 42929 Union FLEEING .evuvvvnvunvevanovarvenn 2 10 42313 Ring Terminal, 3/8 ...ci.
SPRAYER ACCESSORY CONTROL REF. PART NO. DESCRIPTION QTY. 1 92-0251 Fuse H Older ...i.ivereivnnninenunusaonn 2 92-0289 30-mp Fuse (Up Per) .vuevvrnvivronsonan 1 92-0290 10-Amp Fuse (LOWER) ..uivvuvnrvvenasns 1 2 34-74-ED Self-Tap Screw, #8 x 3/8" 4 3 92-0249 Front Panel 1 4 30955 Rubber BOOT ..vivsevnrurnnansvsoonrnns 4 5 30954 Relief Valve Switch (Actuator) 2 6 92-0253 Switch Connector 3 7 92-0352 Jumper Wise 2 8 92-0248 Console Enclosure ...cvvnvevnvaranenns 1 9 92-0256 Magnet .