Operator's Manual

ManualsBrandsToro ManualsSprayersSprayer Tank 1000 for Pro-Control Spray System, Multi-Pro 1100

©The TORO Company - 1999

FORM NO. 95-9308 Rev B

MANUAL VALVE SPRAY SYSTEM

for the MULTI-PRO

1100 Vehicle

OPERATORS

INSTRUCTIONS

To assure maximum safety, optimum

performance, and to gain knowledge of the

product, it is essential that you or any other

operator of this Vehicle read and understand

the contents of this manual before the engine

is ever started. Pay particular attention to the

SAFETY INSTRUCTIONS highlighted by the

triangular safety alert symbol.

SAFETY INSTRUCTIONS

Keep this Operators Manual in the plastic tube behind the operator seat.

It is very important that all persons operating this equipment have easy access to these instructions at all

times!

Carefully read and follow the Set-Up Instructions that are provided with this equipment and the Safety

Instructions in the Multi-Pro

Operators Manual.

RECOGNIZE SAFETY INFORMATION

This safety-alert symbol is used to call

attention to a dangerous situation, which

could result in serious injury or death to

the operator or a bystander.

Safety, mechanical and some general

information in this manual are emphasized.

DANGER, WARNING and CAUTION identify

safety messages. Whenever the triangular safety

symbol appears, it is followed by a safety

message that must be read and understood. For

more details concerning safety, read the Safety

Instructions on this page and page 2.

IMPORTANT identifies special mechanical

information and NOTE identifies general

information worthy of special attention.

These instructions are provided as a guide for the

safe operation and maintenance of this

equipment. However, the operators personal

safety, as well as those persons in the work area,

will depend on the careful actions and good

judgement of the operator. To reduce the

potential for injury or death, comply with the

following safety instructions.

BEFORE OPERATING:

1. Operate this machine only after reading and

understanding the contents of this manual. A

replacement manual is available by sending

complete model and serial number to: Hahn,

Inc., 1625 N. Garvin, Evansville, IN 47711.

2. Learn how to operate the Sprayer and how to

use the controls properly. DO NOT let anyone

operate this equipment without first receiving

thorough instructions.

3. Keep all shields, safety devices and decals in

place. If a shield, safety device or decal is

malfunctioning, illegible or damaged, repair or

replace it before operating the machine.

4. Chemicals can injure persons, animals, plants,

soils or other property. To eliminate environmental

damage and personal injury:

The safety alert symbol means CAUTION,

WARNING or DANGER - personal safety

instruction. Failure to comply with the

instruction may result in personal injury.

A. Select the proper chemical for the job.

B. Follow manufacturers instructions on

chemical container labels. Apply and handle

chemicals as recommended.

C. Handle and apply chemicals with care.

Wear goggles and other necessary protective

equipment. Handle chemicals in well ventilated

areas. Never smoke while handling chemicals.

D. Properly dispose of chemical container

and unused chemicals.

Model No. 41119-90001 & UP

Model No. 41020-90001 & UP

Model No. 41021-90001 & UP

Model No. 41128-90001 & UP

Model No. 41120-90001 & UP

Summary of content (12 pages)

PAGE 1
FORM NO. 95-9308 Rev B Model No. 41119-90001 & UP Model No. 41020-90001 & UP Model No. 41021-90001 & UP Model No. 41128-90001 & UP Model No. 41120-90001 & UP OPERATORS INSTRUCTIONS MANUAL VALVE SPRAY SYSTEM for the MULTI-PROTM 1100 Vehicle To assure maximum safety, optimum performance, and to gain knowledge of the product, it is essential that you or any other operator of this Vehicle read and understand the contents of this manual before the engine is ever started.
PAGE 2
SAFETY INSTRUCTIONS MAINTENANCE: 5. Before servicing or making any adjustments to the Sprayer: A. Stop the Vehicle and set the parking brake. B. Shut off the vehicles engine and remove key from ignition. C. Disengage all power and wait until all moving parts have stopped. 6. Keep all nuts, bolts and other fasteners tightened securely. Replace any shields removed during servicing or adjustments. 7.
PAGE 3
PAGE 4
BEFORE SPRAYING NOZZLE SELECTION: See the nozzle charts on page 5 to be sure that your spray nozzles have the capacity necessary to achieve the application rate selected. EXAMPLE (SI FORMULA): Application Rate = 907 lit/hectare Vehicle Speed = 5 km/h Nozzle Spacing = 50 cm To select the proper nozzle, you need to know: 907 lit/ha x 5 km/h x 50 60,000 1. Recommended chemical application rate in gallons per acre, gallons per 1000 sq. ft. or liters per hectare. With 3.78 lit/min.
PAGE 5
G allons Pe r A cre Ap plication R ate s TORO Nozzle Part No. Number Pressure Capacity G allons per A cre at 20" Spac ings (PSIG) 1 Nozzle (GPM) 20 30 40 50 0.14 0.17 0.20 0.22 2.5 MPH 16.6 20.2 23.8 26.1 Color Code 3 MPH 3.5 MPH 13.9 11.9 16.8 14.4 19.8 17.0 21.8 18.7 4 MPH 4.5 MPH 10.4 9.2 12.6 11.2 14.9 13.2 16.3 14.5 5 MPH 5.5 MPH 8.3 7.6 10.1 9.2 11.9 10.8 13.1 11.9 6 MPH 6.9 8.4 9.9 10.9 95-9221 Y ellow 95-9222 Red 20 30 0.28 0.
PAGE 6
Liters Per Hectare Application Rates TORO Nozzle Pressure Capacity Part No. Number (kPa) 1 Nozzle (L/min) Y ellow 150 200 0.53 0.64 4 km/h 159 192 5 km/h 127 154 6 km/h 106 128 7 km/h 91 110 8 km/h 80 96 9 km/h 71 85 Red 275 350 150 200 0.76 0.83 1.06 1.32 228 249 318 396 182 199 254 317 152 166 212 264 130 142 182 226 114 125 159 198 101 111 141 176 91 100 127 158 83 91 116 144 Brow n 275 350 150 200 1.51 1.70 1.40 1.
PAGE 7
BEFORE SPRAYING Pressure Adjust Knob until the original pressure setting is reached. Turn Left Boom back on. 7. With all Boom ON, switch Center Boom to OFF and adjust the Center Booms By-Pass Pressure Adjust Knob. Turn Center Boom back on. 8. With all Booms on, Switch Right Boom to OFF and repeat this procedure for setting the Right Booms By-Pass Pressure Adjust Knob. Turn Right Boom back on. FILL THE FRESH WATER WASHTANK NOTE: Fill Fresh Water Wash Tank with clean water only.
PAGE 8
OPERATION Watch for plugged Nozzles. Replace all worn Nozzles or those producing streaky or uneven patterns. Stop the spray flow vehicle. before stopping the AFTER SPRAYING: It is extremely important to carefully wash and clean the Tank after every use. Not only the Tank but the Pump, Hoses, Nozzles, Screens, Filters, and the exterior of the Sprayer also should be cleaned. Flush Pump After Use A minimum of three (3) rinses usually is required for all components of the Sprayer.
PAGE 9
PREVENTIVE MAINTENANCE CAUTION The best tension for a V belt drive is the lowest tension at which the Belt will not slip under the highest load condition. Too much tension shortens Belt and Bearing life. ROTATING PULLEYS AND BELTS CAN CAUSE SERIOUS INJURY. Keep Belt and Pulley free from any foreign material which may cause slippage. If a V belt slips, tighten it. Keep hands, feet, and clothing clear while engine is running.
PAGE 10
MAINTENANCE Always flush pump with water, or neutralizing agent before servicing. Refer to the illustrated Parts List for part ordering information. air or hand drill, clean the discharge port, suction port, and the sealing areas of the O-ring on the pump casing and mounting flange. Pump Housing Disassembly In most cases, seal replacement requires disassembly of only the pump half of the unit. 1. Remove the four casing cap screws with a 9/16" box end wrench.
PAGE 11
STORAGE FLUSH PUMP AFTER USE One of the most common causes for faulty pump performance is "gumming" or corrosion inside the pump. Flush the pump and entire system with a solution that will chemically neutralize the liquid pump. Mix according to manufacturer's directions. This will dissolve most residue remaining in the pump, leaving the inside of the pump clean for the next use.
PAGE 12
The Toro Commercial Products Two Year Limited Warranty The Toro Company warrants your 1996 or newer Toro Commercial Product (Product) purchased after January 1, 1997, to be free from defects in materials or workmanship for the period of time listed below. Where a warrantable condition exists, Toro will repair the Product at no cost to you including diagnosis, labor , parts, and transportation. This warranty begins on the date the Product is delivered to the original retail purchaser.