MODEL NO. 41120-40001 & UP MODEL NO. 41128-40001 & UP MODEL NO. 41020-40001 & UP MODEL NO. 41021-40001 & UP MODEL NO. 4113040001 & UP TOR FORM NO. 92-0389 SET-UP AND PARTS CATALOG l PRO-CONTROL™ SPRAY SYSTEM J FOR THE MULTI-PRO 1100™ VEHICLE Refer to the illustrated Parts List for the details of parts used in assembling the Pro-Controi™ System. NOTE: "Right”, "Left", "Front" and “Rear” are referenced while seated in the operator's position. CONSOLE COMPUTER: 1.
CONSOLE COMPUTER (Cont'd.) 11. Conn act the push-on terminal on the red wire to the male terminal on the red wire coming from the Fuse Block. 12. Insert the 20-amp Fuse into the Fuse Block receptacles. NOTE: The remaining Wiring Harness connections will be made after the Tank and Saddle and the Boom Frame are installed on the Vehicle. SPEED SENSOR: 1. Mount the four (4) Wheel Magnets to the inside rim of the Vehicle's left rear wheel with eight {8) hex nuts and four (4) lock washers as shown in FiG. 3.
. Clevis Pin 4. Hair Pin Cotter 1. Pivot Mounting Plate 2. Pump Pivot Plate 2. Align the pivot tubes on the Pump Pivot Plate with those on the Pivot Mounting Plate. Insert the M?t {2} clevis pins and secure with two {2} hairpin crofters. NOTE: In the following instructions, “sealer” refers to RTV clear silicone. 3. Secure the Centrifugal Pump in a vise. Apply thread sealer and install the fittings to connect the Suction, Suppl, Agitator and Overflow Hoses to the Pump as shown in FIG. 5. % g Mower . Suppl .
CENTRIFUGAL PUMP (CONT'D): if Step 13 does nat achieve the necessary tension on the Control Cable, loosen the Pump mounting obits and slide the Pump on the Pivot Plate to move it away from the Vehicle Frame, increasing the Cable tension. TANK ASSEMBLY: 1. Cut the shipping straps and remove the Spray Tank and Saddle Assembly from the shipping skid. NOTE: _Therein following instructions, sealer refers to RTV clear silicone when used for pipe fittings. FIG.7 1. Barbed Elbow 3.
FLOW METER (Cont'd): 2. Slide a hose barb into the other end of the Adapter Hose and secure with a hose clamp. 3. Apply thread sealer and attach the 1" male quick couplet to the hose barb's threaded end. 4. Secure the Flow Meter to the Mounting Bracket with the two (2) hose clamps famished. 5. Position the completed Flow Meter Assembly on the Mounting Bracket as shown in FIG. 8. IMPORTANT!The flow must be in the direction of the arrow on the Flow Meter. 6.
BOOM FRAME (Cont'd): 8. Loosely attach the triple barb Nozzle Assembly in the approximate center of the Center Boom Pipe. For the most uniform spray coverage, position all Nozzle Assemblies at a 45° angle as shown in FIG. 10. Tighten clamp screw to secure the Nozzle to the Boom Pipe. 9. Loosely attach a single barb Nozzle Assembly to each end of the Center Boom Pipe. Place two hose clamps on the two 3/4“ x 18" Jumper Hoses and connect the single garb Nozzles to the triple barb Nozzle.
1. Control Naive 8. Solenoid Mtg. Strap 2. Solenoid Says. 7. Pressure Gauge 3. Central Naive Brit. 8. Barbed Elbow 4. Cross Support Angle 8. Boom Feeder Hose 5. Flow Meter Hose 5, Slide the Solenoid Mounting Strap into position and mount the complete Control Naive and Solenoid Assembly to the Cross Support as shown in FIG. 13. Use four 5/16" x 1" hex hd cap screws with four washers placed below the screw heads, two between the strap and the Cross Support and four below the Cross Support under the nuts. 8.
PRO-CONTROL™ TANK 1100) Ret Part No. Description Qty Ref| Earl No.
BOOM FRAME (MULTI-PRO 1100) A CAUTION! THE TWO SPRINGS (REF. #24) ARE UNDER APPROX. 150 LBS. OF PRESSURE. BE VERY CAUTIOUS WHEN REMOVING THE SPRING PINS (REF. #26) FOR REMOVAL OF THE SPRINGS. A CAUTION! THE TWO BOLTS (REF. #8) MUST BE TORQUED TO 50 FT. LBS.
BOOM FRAME 1100) :rehi Part No. Description Qty Ref, Part No. Description Qty |1 42023 Tube Wedge Says 2 28* Flat Washer, BURSAE.
CENTRIFUGAL PUMP & FLOW METER (MULTI—PRO 1100) Re fl Part No. Description Qty Hel; Part No. Description Qty 1141307 90 Deg. St.
MOTORIZED CONTROL VALVE & BOOMS (PRO—CONTROL™) Ret Part No. Description Gty Ref| Part No. Description 140485 Pressure Gage 1 24 (920358 Hectic Solaced Valve {100 P.8.
PRO-CONTROL™ CONSOLE (1100 MULTI-PRO) 16 felt! Part No. Description Qty Ref sampan N;): Description __aty 142722 Power Switch t 12 18 1 242128 Rate 1/ Rate 2/ Man, Switch i 18 1928687 Clemons Control Cable (18 1) 1 3142724 Man. Adj.
FLOW METER (41482) CONTROL VALVE (41480) fetal Part No. Description Qiy Hef! Part No. Description Qty 1142478 Sensor Housing 1 1142818 Valve Cover 1 2142476 #1032 x 8/4 Screw (Stanley. Steel) € 2142482 #6—20x 3/4 Thread Forming Craw 6 3 42466 O-Ring (Vito) 1 3142483 Motor Says 1 4 42477 Transducer Says.
SAFETY AND INSTRUCTION DECALS CHEMICALS CAN BE HAZARDOUS TO REDUCE THE RISK OF ENVIRONMENTAL SONAR INJURY. oAt HANDLE AND APPLY CHEMICALS WEAR PROTECTIVE CLOTHING AND MASK. L WASH CONTAINER Part No. 93-0688: Located on Lid of Sprayer Tank. ONLY. Part No. 93-0800: Located on side of Clean Water Wash Tank Sadie.