FORM NO. 42957 MODEL NO. 41120,41121, SET-UPLAND \ 41021, 41038 and PARTS LIST PRO-CONTROL SPRAY SYSTEM FOR USE ON THE MULTI-PRO 1100 VEHICLE Refer to the illustrated Parts List for the details of parts used in assembling the PRO-CONTROL Sprayer System. “Right" and "Left® as used in the following Instructions, refer to the operator’s right and left when seated in the normal operating position., Likewise, “Front* and *"Reaar® as seen from the operator’s position.
TANK ASSEMBLY -(Continued) ® Apply thread sealer and install the 907 street elbow and a hose barb into the fitting &t the rear of the Tank. Attach the 1" x 38" Overflow Hose to the hose bark with a hose clamp. Attach a female Wiki-Coupler to the other end of the Overflow Hose with a hose clamp. ® Lace the Tank and $addle Assembly on the Vehicle Frame. Secure to the Vehicle with two 1/2° x . hex hd cap. screws. and hex nuts through the rear mounting member of the Saddle Assembly.
BOOM ASSEMBLY: Use a paint brush to apply 2 heavy coating of grease to the tubes which 2re to be inserted into the Vehicle Frame. W Install the two Boom Mount Assembly into the Vehicle Frame as shown in FIG. 8. Use a torque wrench to tighten the long (174" x 8") screws which join the Wedges to the tubes. Tighten to 50 ft. ibs. CAUTION! FAILURE TO TIGHTEN THESE SCREWS SECURELY COULD RESULT IN THE ROOM FRAME FALLING OFF THE VEHICLE! THESE INSTRUCTIONS APPLY TQ THE ASSEMBLY.
BOOM ASSEMBLY (continued) m Insert an Extension Boom Pipe into the pivot Assembly and secure with four 1/4° x hex hd cap screws and lock nuts. See FIG. 8. Repeat on the opposite side to assemble the other Extension Boom. ® Attach the Boom Support Assembly to the pivot Assembly, using a 5/16" x screw and hex nut. See FIG. 8. Secure the two plates of the Boom Support Assembly to the Extension Boom Pipe, using two U-bolts and four lock nuts.
LOW METER: Attach the Adapter Hose and the male Wiki-Coupler to the rear barb on the Flow Meter. Connect the Supply Hose +to the front barb on the Flow Mete. W Secure the complete Flow Meter Assembly to the Mounting Bracket with the two large hose clamps. ® Attach the Mounting Bracket to the left rear Fender as shown in FIG.
TANK REF PART WO. DESCRIPTION oY 1 42983 Hold~In Crabs Says 2 2 22-12-AGED Hex Nut, 5/18 24-10-DB Flat Washer, 5/16 . 4 4 42880 Mounting Band (Front) 2 5 5128 U-Bolt, 1/4 NC .souvenir 4 & 42138 Rubber Hold Down Strap . 2 7 42259 Boom Hold-In Says. L.H. 1 8 25-25-gad Carriage Bolt, 5/16 22-11-RID Hex Nut, 1/4 NC 8 10 42316 Boom Hold-In Says. R.H. . 1 11 43013 Mounting Band (Rear)} 2 12 42277 Pressure Gage Bracket Says 1 13 42452 Protective CAR ..
A CAUTION! THE THO SPRINGS (REF. #24) ARE UNDER APPROX. 150 LBS. OF PRESSURE. 8E VERY CAUTIOUS WHEN REMOVING THE SPRIG PINS (REF, $26) FOR REMOVAL OF THE SPRINGS. A CAUTION! THE TWO BOLTS (REF, #8) MUST BE TORQUED TO 50 FT. LBS.
BOOM FRAME REF PART NO. DESCRIPTION QTY 1 Tub Wedge SAYS «.avenue 2 2 Lock Nut, 172 Cross Support Angle . 1 4 BASICS, 1/2 NC x . 2 5 Spacer Tube, 1 1/4" lg. 2 & Boom Mount Says 1 7 Boom Mount SAYS 1 8 BASICS, Center Boom Angle 2 10 Flat Washer, 8716 ...enviousness 4 11 Hex Nut, 5/16 HHS, 24w11-2D Flat washer, 40493 Center Boom Pipe . 1 15 40494 Clamp SAYS soybean 2 16 22~13~AJFD Lock Nut, 3/8 NC +.cenvsevarsoarss 2 17 42227 Main Frame Tube~Welded Says 1 18 42287 Spacer Tube, 1* Lg.
PUMP REF PART NO. DESCRIPTION QY 1 41307 90°st. Elbow, 1% NPT Aeneas 2 2 41308 Reducer Bushing, 1% x 1/2" 41314 close Nipple, 1/2% NPT 1 4 40192 Ball Valve, 1/2" NPT 1 5 40486 Wiki Adapter x 1/2" MPT . 1 41317 Wiki Adapter Cap 1 6 41308 Tee, 17 NPT . 3 7 41304 close Nipple, 1" NPT 4 8 41308 Hose Barb, 1" MPT x 1-1/4 H.B. 2 9 41327 HOVE. Cl Land 4 10 42996 Supply Hose, x T 11 41484 Console Control Cable (10 ft.
MOTORIZED CONTROL VALVE & BOOMS REF PART NO. DESCRIPTION oTY 1 40488 Pres pure GAUGE covscerrnseoniccooenan 1 2 42277 Outage Mounting Bracket .. 1 3 41292 90°Elbow, 1/4 MPT x 3/8 Earl . 1 4 96609 Hose Clamp, 3/8 Hose . 2 s 42276 Hose (Pressure Gage) 3/8 1 6 26393 Hose Clamp, . 1 7 10380 Wiki Soupier, 1 & 21146 Hose Clamp, 1" Hose B 2 g 42998 Flow. Hester Hose, 1% 2. 24% .recurrence . 1 10 41730 Hose Barb, 3/4 XPT x 1" Barb . 1 11 42939 45°8t.
ENLARGED HOLE SPEED SENSOR PART NO. DESCRIPTION QTY Hex Nut, 1/2 NC i.avuev..n 8 41475 Magnet Ray. (Rely SCINTILLATE 41476 Magnet Says. (Black) 2 41477 Sensor Switch BEYS +.eesrs 1 41478 Sensor ROQ .eescisvonrsvns 1 41478 Turret ABBY sereneness 2 23-9-GD Lock Washer, 1/4 2 22-11-AGED Hex But, 1/8 NC suvvanvons 2 CONTROL CONSOLE REF PART NO. DESCRIPTION QTY 1 42722 POWER Switch «evokes diaereses L 2 42723 Rate 1/Rate 2 Manual Switch } 3 42724 MaN ADJ Switch convinces i 4 42558 BOOM Switch “.