MODEL NO. 41122-50001 & UP MODEL NO. 41020-50001 & UP MODEL NO. 41021-50001 & UP MODEL NO. 41128-50001 & UP STANDARD ELECTRIC SPRAY SYSTEM 1000 FOR THE MULTI-PRO™ 1100 VEHICLE FORM SET-UP AND PARTS CATALOG Refer to the illustrated Parts List for the details of parts used in assembling the Standard Electric Spray System. NOTE: "Right’, "Left', "Front’, and "Rear" are referenced while seated in the operator's position. TACHOMETER: 1.
4. Measure carefully and determine the length of white wire necessary to reach the Ground Terminal Block. Cut off the excess wire and crimp the spade terminal onto the stripped end. Connect the spade terminal 1o the Ground Terminal Block as shown in FIG. 3. 5. Measure carefully to determine the length of red wire necessary to reach the Fuse Block. Cut off excess wire and crimp the push-on germinal onto the stripped end.
Engine's Drive Pulley. When alignment is correct, Enlighten the two (2) set screws in the Spurn Pulley's ub. 7. Install the Pump Drive Belt around the Pump and Engine drive Pulley. 8. Loosely mount the Pump Belt Cover to the Pump hub with the Pump Cover Clamp and the two (2) 5/16" flat washers, lock washers, and hex nuts. See FIG. 6. 9. Insert the 3/8"x 4" cap screw through the Pump Cover and into the heel in the Pump Cable’s end Secure the Gable to the Cover with a 3/8" ock nut, FiG. 6 1.
8. Secure the Mounting Member to the Vehicle's cross member with two (2) 1/2" x cap screws, flat washers, lock washers and hex nuts. 9. Route the Suction Hose over the left side of the Vehicle Frame and connect the couplets at the Suction Ball Valve. 10. Route the Agitator Hose over the Vehicle Frame and under the Pump to connect the couplets at the Agitator Ball Valve. BOOM HOLD-IN ASSEMBLY: 1.
1. Cross Support Angle 8. Boom Clamp 2. Boom Mount Says. 8. Triple Barb Nozzle Body 3. Spacer Tube, 1" ig. 19. Single Barb Nozzle Body 4. Spacer Tube, 11. Jumper Hose 5. Main Frame Tube 12, Strut Assembly &, Center Boom Angle 183, Adjustable Clevis 7. Center Boom Pips 7. Loosely attach the triple barb Nozzle Assembly in the approximate center of the Center Boom Pipe. For the most uniform spray coverage, position all Nozzle Assemblies at a 45° angle as shown in FIG 10.
15. Attach three double barb and one single barb Nozzle Bodies with Clamp Assemblies on each Extension Boom Pipe as shown in FIG. 12, Nozzles are to be spaced on 20" centers. Connect the Nozzle Assemblies with the 3/4" x 19" Jumper Hose and 3/4” x 21" Jumper Hose. Secure with hose clamps. 18. Install the plastic Boom Caps over the ends of the Boom Pipes. 17. Recheck and tighten all fasteners and hose clamps securely. CONTROL VALVE/SOLENOID ASSEMBLY: 1.
STANDARD ELECTRIC SPRAY SYSTEM PUMP SET-UP Ref| Part No. Description Gty Rei! Part No. Description Qty 1 [93-0856 190° Elbow 1-1/4 NPT 1 22 40487 Quick Couplet x 1/2 Hose Barb 1 2 41327 Hose Clamp 2 23 96608 Hose Clamp 2 3 193-0858 [Suction Hose 26 1 24 142946 i Agitator Hose 1 |4 |93-0854 Quick Couplet x 1-1/4 Hose Barb 1 28 120-49-GAD JHHCS, 3/8 NCx 1-1/2 2 6 183-0888 [Quick Barb x 1-1/4 Marla NPT 1 26 192-3771 Pump Pivot Plate Says.
CONTROL VALVE & BOOMS Bet | Part No, Description Gty Ref | Part No. Description Qty. 1 140480 {Quick Adapter x 1* H.B, 2] 1611 Seal Kit for Solenoid AR] 2 21146 Hose Clamp 4] 123 141310 Seducer Bushing, 1 3 42004 Supply Hose, |3/4 MPT x 1/4 FPT 4 41730 Hose Barb, 8/4" MPT MO165 [Overflow Hose, 42838 45 St. Elbow, 3/4" NPT 2] 125 140606 imper Hose, 374 [24-10-DB [Flat Washer, 5/16 STAEL. 11 26 M22e2 Extension Broom Pips Says 2 |7 {20-26-GAD [HH.C.S.
STANDARD ELECTRIC SPRAY SYSTEM TANK (MULTI-PRO 1100) Rel Part No. Description Qty Ref | Part No. Description Qty | 1 |¢2083 Hold-In Brace Assembly 2 123 143068 Fiy Nut, 2" NPT 1 g [8217-6 Hex Nut, 5/16 NC & 24 (43067 Sealing Washer 1 3 |3286-23 Flat Washer, 516 4| {25 143086 Bulk Head, 2" NPT 1 4 [92-0010 U-Bolt, 141800 [Frank Titling, 1" NPT (fiw Tank Says} | 1 5 K219 Rubber Hals-Down 3 27 Ciao 180° Bt.
CONTROL CONSOLE 12 Regret Part No. Description Oty Ref Pant No. Description Qty 1 42983 12-10 AWG Female Terminal 2| 14 [42821 [Boom Switch 3 2 42034 1614 AWG Female Terminal 1 15 [42924 [Pressure Gauge 1 3 142832 insulated Female Terminal 3 93-1042 [Fern ale Gauge Fitting 1 4 [93-1028 Solenoid Valve 1 16 42085 [Fuse Holder 1 B 42008 Contrition Naive 1 [4262¢ 16 Amp Fuse 1 § 142831 Male Fitting 1 17 42027 [Pressure Adjust Switch 1 7 142930 (Gauge Tubing 1 18 [20-26-GAD H.H.C.
SOLENOID VALVE (93-1027) Ret] Part No. Description Qty Ref| Part No. Description Gty 1 j92-0358 l Jam Nut, Nickel Plated 1 12 * Diaphragm, Vito 2 2 2126 [Screw Stainless Ste! 2 13 [83-1034 [Seat Washer Retainer, $.5.
BOOM FRAME (MULTI-PRO 1100} A CAUTION ) ARE LBS. OF (REF # 24 150 PRESSURE. BE VERY CAUTIOUS WHEN REMOVING THE SPRING Ninepins #286) THE TWO SPRINGS UNDER APPROX. FOR REMOVAL OF THE SPIN ) REF #8 . LBS.
BOOM FRAME (MULTI-PRO 1100) Ref] Part No. Description Qty Ref [Part No. Description Qty, 1 {42223 Tube Wedge Says 2| 23" |24-18-BD [Flat Washer, 1" SAE. 2 |2 R2-15-AJF {Lock Nut, 142186 [Compression Spring 2 13 {42226 Cross Support Angles 1 |25 1 42706 Breakaway Pivot Says 2 4 P0-86-AGDHHCS, 1/2 NG x 2] 28" | 26-139-C [Spring Pin, 1/4x 2° 2 5 |42258 Spacer Tube, [g. 2 127 124-10-DB [Flat Washer, 516 STAEL.
CENTRIFUGAL PUMP (93-0848) 18 Ref| Part No, Description Qty. Ref| Part No.