Installation Instructions

ManualsBrandsToro ManualsSprayersSprayer Pump 1000 for Injector Pro, Multi-Pro 1100

SET-UP AND PARTS

CATALOG

VEHICLEFOR THE MULTI-PRO

1100

Refer to illustrated Parts List for details of parts used in assembling the Standard Electric Spray System.

FORM NO.99-0550 REV.B

1. Tachometer 2. Grommet

3. Decal

NOTE: "Right", "Left", "Front", and "Rear" are

referenced while seated in the operator's

position.

IMPORTANT: Keep wire clear of extremely hot

engine parts such as the muffler, etc.

5. Route the Cable through the "U" shaped

bracket under the floorboard, and up into the

engine area to the right of the Transmission.

6. Slip red wire over an insulated section of the

Spark Plug Wire and wrap 4 turns. See FIG. 2.

1. Spark Plug Wire 3. Spade Terminal

2. Ground Terminal Block 4. Tachometer Cable

TACHOMETER:

1. Remove four (4) 1/4" x 5/8" washer hd cap

screws to remove the rear panel from the Steering

Console.

2. Install the Tachometer to the right side of the

Steering Column using two (2) #8 x 5/8" hex hd

machine screws, lock washers, and hex nuts. See

FIG.1.

3. Route the Tachometer Cable through the hole

in the top of the Steering Console below the

Tachometer and install Grommet into hole around

Cable. See FIG. 1.

4. Install RPM to Speed Decal above

Tachometer.

MODEL NO. 41122-90101 & UP

MODEL NO. 41020-90101 & UP

MODEL NO. 41021-90101 & UP

MODEL NO. 41128-90101 & UP

MODEL NO. 41120-90101 & UP

STANDARD ELECTRIC SPRAY SYSTEM 1000

CONTROL CONSOLE:

1. Using two 1/4" hex washer hd screws, install

the Mounting Bracket for the Console Control on

the left side panel of the Seat Support.

2. Route the Cable Assembly along the rear of

the seat support. Place an R-clamp around the

Cable and secure it to the Seat Support with a

5/16" x 3/4" cap screw, flat washer and hex nut.

3. Route the Cable along the left side and to the

rear of the Vehicle frame. Secure with plastic tie-

straps.

7. Ground the spade terminal on the white wire

to the Ground Terminal Block mounted inside the

Seat Box. After the connections are made, coil

up any excess wire and tie strap to a convenient

area. See FIG. 2.

8. Reinstall Rear Panel.

FIG. 1

FIG. 2

Summary of content (16 pages)

PAGE 1
MODEL MODEL MODEL MODEL MODEL NO. NO. NO. NO. NO. 41122-90101 41020-90101 41021-90101 41128-90101 41120-90101 & & & & & UP UP UP UP UP FORM NO.99-0550 REV.B SET-UP AND PARTS CATALOG STANDARD ELECTRIC SPRAY SYSTEM 1000 FOR THE MULTI-PROTM 1100 VEHICLE Refer to illustrated Parts List for details of parts used in assembling the Standard Electric Spray System. NOTE: "Right", "Left", "Front", and "Rear" are referenced while seated in the operator's position. TACHOMETER: 1.
PAGE 2
4. Measure carefully and determine the length of white wire necessary to reach the Ground Terminal Block. Cut off the excess wire and crimp the spade terminal onto the stripped end. Connect the spade terminal to the Ground Terminal Block as shown in FIG. 3. NOTE: In the following instructions, "sealer" refers to RTV clear silicone. 3. Secure the Centrifugal Pump in a vise. Apply thread sealer and install the fittings to connect the Suction, Supply, and Agitator Hoses to the Pump as shown in FIG. 5. 5.
PAGE 3
8. Loosely mount the Pump Belt Cover to the Pump hub with the Pump Cover Clamp and the two (2) 5/16" flat washers, lock washers, and hex nuts. See FIG. 6. 9. Insert the 3/8" x 4" cap screw through the Pump Cover and into the hole in the Pump Cable's end fitting. Secure the Cable to the Cover with a 3/8" lock nut. 10. Remove the hair pin cotter and flat washer from the pin in the Accessory Control Lever. Push the Control Lever down (engaged).
PAGE 4
8. Secure the Mounting Member to the Vehicle's cross member with two (2) 1/2" x 1-1/2" cap screws, flat washers, lock washers and hex nuts. 9. Route the Suction Hose over the left side of the Vehicle Frame and connect the couplers at the Suction Ball Valve. BOOM FRAME ASSEMBLY: 1. Apply a heavy coating of grease to the tubes of the two Boom Mount Assemblies and insert them into the Vehicle frame as shown in FIG 9. 10.
PAGE 5
FIG. 11 1. Extension Boom Pipe 2. Pivot Assembly FIG. 10 1. Cross Support Angle 2. Boom Mount Assy. 3. Spacer Tube, 1" lg. 4. Spacer Tube, 1-1/4" lg. 5. Main Frame Tube 6. Center Boom Angle 7. Center Boom Pipe 8. Boom Clamp 9. Triple Barb Nozzle Body 10. Single Barb Nozzle Body 11. Jumper Hose 12. Strut Assembly 13. Adjustable Clevis 3. Boom Support Assembly 4. Height Adjustment 11. Attach the Boom Support Assembly to the Pivot Assembly, using a 5/16" x 1-1/2" cap screw and lock nut. See FIG. 11 & 12.
PAGE 6
14. At the adjustable clevis assemblies (FIG. 10) adjust booms to the level position by adjusting the jam nuts to the desired position, then tighten the end nuts against the Boom Frame Support member. 15. Attach three double barb and one single barb Turret Assemblies on each Extension Boom Pipe as shown in FIG 12. Turret Assemblies are to be level and spaced on 20" centers. Connect the Turret Assemblies with the 3/4" x 19" Jumper Hoses. Secure with hose clamps.
PAGE 7
1391 STANDARD ELECTRIC SPRAY SYSTEM PUMP SET-UP Ref 1 2 3 4 5 6 7 8 9 * * Part No. 93-0856 41327 93-0858 93-0854 93-0888 93-0853 93-0897 93-0855 92-0050 42701 93-0687 94-7065 * * 10 11 12 13 14 15 16 17 18 19 42702 42703 42056 93-0848 92-0049 42992 3256-26 41307 92-8416 41315 41306 41314 * Description 90° Elbow 1-1/4 NPT Hose Clamp Suction Hose 1-1/4 x 25 Quick Coupler x 1-1/4 Hose Barb Quick Barb x 1-1/4 Male NPT Quick Coupling Dust Cap St.
PAGE 8
1372 CONTROL VALVE Ref Part No. Description 1 2 3 4 Control Valve Bracket 1 Solenoid Valve Bracket 1 Throttling Valve 3 Bypass Solenoid Valve Assembly 1 Single Solenoid AR Hose Barb, 90° 1/2" x 3/4" HB 3 Hose Clamp 6 Hose Bypass, 1" x 29" 1 Hex Nut, M6-1 3 Lock Washer 3 Hex Flange Nut 4 HHCS 4 5 6 7 8 9 10 11 8 99-0529 99-0528 42872 99-0530 99-0536 92-8557 92-0045 40165 43-2830 48-8020 32128-20 3234-5 Qty Ref Part No.
PAGE 9
TURRET BODIES & BOOM HOSES Ref. Part No. Description * 95-9183 * 95-9181 * 95-9184 1 2 †3 4 5 6 †7 8 †9 †10 †11 †12 13 14 99-0811 99-0812 95-9191 95-9192 95-9197 95-9196 95-9198 95-9200 95-9199 99-0815 99-0813 41003 95-9193 95-9202 Turret Body - Double Barb (Incl. Ref. #’s 1-14) Turret Body - Single Barb (Incl. Ref. #’s 1-13 & 15) Turret Body - Barb x 1/2 NPT (Incl. Ref.
PAGE 10
STANDARD ELECTRIC SPRAY SYSTEM TANK (MULTI-PRO 1100) 1094-2 TACHOMETER 10
PAGE 11
STANDARD ELECTRIC SPRAY SYSTEM TANK (MULTI-PRO 1100) Ref Part No. Description Qty Hold-In Brace Assembly 2 23 43068 Fly Nut, 2" NPT 1 22-12-AJD Hex Nut, 5/16 NC 6 24 43067 Sealing Washer 1 24-10-BD Flat Washer, 5/16 4 25 43066 Bulk Head, 2" NPT 1 4 92-0010 U-Bolt, 1/4 NC 4 26 41800 Tank Fitting, 1" NPT (f/w Tank Assy) 1 5 42198 Rubber Hold-Down 3 27 41307 90° St.
PAGE 12
CONTROL CONSOLE Ref Part No. Description Qty Ref Part No. Description Qty 1 42933 12-10 AWG Female Terminal 2 15 42924 Pressure Gauge (PSI) 1 2 42934 16-14 AWG Female Terminal 1 16 42925 Fuse Holder 1 3 42932 Insulated Female Terminal 3 42926 15 - AMP Fuse 1 4 99-0530 Solenoid Valve Assembly 1 17 42927 Pressure Adjust Switch 1 99-0536 Single Solenoid A/R 18 322-5 H.H.C.S.
PAGE 13
SOLENOID VALVE (99-0536) Ref. Part No. Description 1 95-9317 Coil Assy - Nylon Encapsulated 2 3 Qty. Ref. Part No. Description Qty. 1 9 42136 Spacer - Stainless Steel 2 Spring - Stainless Steel 1 10 93-1035 Body - Polypropylene (black) 1 95-9318 Armature - Stainless Steel 1 11 92-1036 Stem - Stainless Steel 1 4 95-9319 Retaining Ring - Steel, Plated 1 12 92-0367 Lower Diaphragm Piston - S.S.
PAGE 14
1095 14
PAGE 15
BOOM FRAME (MULTI-PRO 1100) Ref 1 Part No. Description Qty Ref Part No. Description Qty 42223 Tube Wedge Assy 2 24* 42196 Compression Spring 2 2 32153-5 Lock Nut, 1/2 NC 4 25* 42706 Breakaway Pivot Assy 2 3 42225 Cross Support Angle 1 26* 321121-78 Spring Pin, 1/4 x 2" 2 4 325-5 HHCS, 1/2 NC x 1-1/4" 2 27 3256-23 Flat Washer, 5/16 S.A.E. 3 5 42258 Spacer Tube, 1-1/4" lg.
PAGE 16
15 11 14 13 12 9 10 8 11 7 6 5 16 4 3 2 1 1 CENTRIFUGAL PUMP (93-0848) Ref Part No. 1 42084 2 93-0922 3 42086 4 93-0923 5 42089 6 42088 7 93-0924 8 42092 16 Description Drain Plug Pump Casting Impeller Nut Impeller (Polypropylene) O-Ring Mechanical Seal - Viton Seal Retainer Slinger Ring Qty 4 1 1 1 1 1 1 1 Ref Part No.