Operator's Manual

ManualsBrandsToro ManualsSprayersHand Spray Wand Kit, Multi Pro 1750 or Multi Pro WM Turf Sprayer

FormNo.3378-318RevA

HandSprayWandKit

MultiPro1750orMultiProWMTurfSprayer

ModelNo.41131

Operator'sManual

Thehandspraywandkitisanattachmentforaturfspray

applicationvehicleandisintendedtobeusedbyprofessional,

hiredoperatorsincommercialapplications.Itisprimarily

designedforsprayingonwell-maintainedlawnsinparks,golf

courses,sportselds,andoncommercialgrounds.

WARNING

CALIFORNIA

Proposition65Warning

Thisproductcontainsachemicalorchemicals

knowntotheStateofCaliforniatocausecancer,

birthdefects,orreproductiveharm.

Useofthisproductmaycauseexposureto

chemicalsknowntotheStateofCalifornia

tocausecancer,birthdefects,orother

reproductiveharm.

Setup

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

Hosehook1

Flatwasher2

Flange-headnut4

Carriagebolt

R-clamp2

Spraygunbracket

Installthehosehookandspraygun

bracket.

Manualvalveassembly1

Threadedrod4

O-ring

Hosebarb1

Installthevalveassembly.

Hose1

Hoseclamp1

Installthesupplyhose.

Spraygunassembly

Hoseclamp1

Connectthesprayhose.

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

Note:Threadsealingtapeisusedintheinstallationofthiskit.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3378-318*A

Summary of content (8 pages)

PAGE 1
Form No. 3378-318 Rev A Hand Spray Wand Kit Multi Pro 1750 or Multi Pro WM Turf Sprayer Model No. 41131 Operator's Manual The hand spray wand kit is an attachment for a turf spray application vehicle and is intended to be used by professional, hired operators in commercial applications. It is primarily designed for spraying on well-maintained lawns in parks, golf courses, sports fields, and on commercial grounds.
PAGE 2
1 Preparing the Machine No Parts Required Procedure 1. Ensure that the machine is empty of all fluids. If chemicals have been used in the machine, flush the system thoroughly with clean water and drain the water; refer to your vehicle Operator’s Manual for instructions. Figure 1 Multi Pro 1750 2. Disconnect the negative battery terminal from the battery. 2 1. Flange-head nut 5. Front, right-hand tank strap 2. Flat washer 6. Spray gun bracket 3. Hose hook 7. R-clamp 4.
PAGE 3
4. Install the hose hook as shown in Figure 1 or Figure 2 using a carriage bolt, flat washer, and flange-head nut. 3 Installing the Manual Valve Parts needed for this procedure: 1 Manual valve assembly 4 Threaded rod 1 O-ring 1 Hosebarb Figure 4 1. O-ring 3. Pressure-gauge port 2. Manual valve 4. Stabilizing bracket 4. Secure the bolts of the stabilizing bracket to the mounting rail. Procedure 4 1.
PAGE 4
Operation 5 WARNING Connecting the Spray Hose Fluid under pressure can penetrate skin and cause injury. Parts needed for this procedure: 1 Spray gun assembly • Keep your body and hands away from nozzles that eject high pressure fluid. 1 Hose clamp • Do not aim the sprayer at any person or animal. • Ensure that all fluid hoses and lines are in good condition and all connections and fittings are tight before applying pressure to the system. Procedure 1.
PAGE 5
Switching from Boom Spray Mode to Hand Spray Mode 1. Stop the machine, turn the booms off, and set the parking brake. WARNING Driving while using the hand sprayer can cause loss of control, resulting in injury or death. Do not operate the hand sprayer while driving. 2. At the back of the machine, ensure that the trigger lock on the spray gun is locked. 3. Flip the lever on the control valve to the Open position. 4. At the operator's position, turn the pump on. 5. Switch the master boom to the On position.
PAGE 6
Notes: 6
PAGE 7
Notes: 7
PAGE 8