Installation Instructions

ManualsBrandsToro ManualsAttachmentsSpray Gun Kit, Multi-Pro 1200/1250 Turf Sprayer and Workman 200 Spray System

FormNo.3372-587RevA

SprayGunKit

MultiPro

1200/1250TurfSprayerandWorkman

200Spray

System

ModelNo.41133—SerialNo.313000001andUp

InstallationInstructions

Thehandspraygunkitisanattachmentforaturfspray

applicationvehicleandisintendedtobeusedbyprofessional,

hiredoperatorsincommercialapplications.Itisprimarily

designedforsprayingonwell-maintainedlawnsinparks,golf

courses,sportselds,andoncommercialgrounds.

ThisproductcomplieswithallrelevantEuropeandirectives.

Fordetails,pleaseseetheseparateproduct-specic

DeclarationofConformity(DOC)sheet.

Readthismanualcarefullytolearnhowtooperateand

maintainyourproductproperly.Theinformationinthis

manualcanhelpyouandothersavoidinjuryandproduct

damage.AlthoughTorodesignsandproducessafeproducts,

youareresponsibleforoperatingtheproductproperlyand

safely.

YoumaycontactTorodirectlyatwww.Toro.comforproduct

andaccessoryinformation,helpndingadealer,ortoregister

yourproduct.

Wheneveryouneedservice,genuineToroparts,oradditional

information,contactanAuthorizedServiceDealerorToro

CustomerServiceandhavethemodelandserialnumbersof

yourproductready.Figure1illustratesthelocationofthe

modelandserialnumbersontheproduct.

G021201

Figure1

1.Modelandserialnumberplate

ModelNo.

SerialNo.

Safety

Thismanualidentiespotentialhazardsandhassafety

messagesidentiedbythesafetyalertsymbol(Figure2),

whichsignalsahazardthatmaycauseseriousinjuryordeath

ifyoudonotfollowtherecommendedprecautions.

Figure2

1.Safetyalertsymbol

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3372-587*A

Summary of content (8 pages)

PAGE 1
Form No. 3372-587 Rev A Spray Gun Kit Multi Pro® 1200/1250 Turf Sprayer and Workman® 200 Spray System Model No. 41133—Serial No. 313000001 and Up Installation Instructions The hand spray gun kit is an attachment for a turf spray application vehicle and is intended to be used by professional, hired operators in commercial applications. It is primarily designed for spraying on well-maintained lawns in parks, golf courses, sports fields, and on commercial grounds.
PAGE 2
This manual uses 2 words to highlight information. Important calls attention to special mechanical information and Note emphasizes general information worthy of special attention. • Do not use the hand sprayer if the hose, trigger lock, Read also the safety and operation instructions in the vehicle Operator’s Manual. • Do not spray near power lines; the spray stream could nozzle, or any other part is damaged or missing.
PAGE 3
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 Description Use Qty.
PAGE 4
5. Secure the tank strap using the fasteners you removed previously.
PAGE 5
7. Install the control valve bracket between the supply tee bracket and the vehicle (Figure 7). 3. Remove the 2 screws securing the supply tee to the mounting bracket. Remove the supply tee and hoses (Figure 5). 1 2 3 2 1 4 G021195 Figure 7 G021194 1. Mounting frame 3. Bolt 2. Control valve bracket 4. Supply tee mounting bracket Figure 5 1. Supply-tee mounting bracket 8.
PAGE 6
1 5 2 6 5 7 3 2 4 2 4 1 1 3 2 G021198 Figure 10 G021197 Figure 8 1. Flange nut 3. Support bracket 2. Flange-head bolt 4. Control valve bracket 1. Adapter 5. Plastic nut 2. Large O-ring 6. Reducer nipple 3. Large plastic nut 7. Reducer assembly 4. Tee • On a Workman Spray System (Figure 9), remove 14. Turn the large plastic nut to secure the tee assembly to the control valve (Figure 10).
PAGE 7
4 Installing the Supply Hose Parts needed for this procedure: 1 Hose 1 Hose clamp 1 Spray gun 1 O-ring Procedure 1. Locate the O-ring in loose parts and lubricate it using a non-petroleum based lubricant such as vegetable oil. Install the O-ring between the long hose and the control valve assembly (Figure 11). G021235 Figure 13 2. Connect the threaded fitting on the end of the long hose to the control valve assembly (Figure 11). 3.
PAGE 8
Important: Do not pull the hose with the spray gun. Always hold the hose and pull on it directly. Pulling on the hose with the gun may break the fitting on the gun or damage the hose. • Avoid stationary spraying when conditions are very hot and/or dry, as turf can be more stressed during these periods. • Avoid parking on the turf while stationary spraying. Park on a cart path whenever possible. 2. Release the trigger lock. • Minimize the amount of time the machine is left 3.