Installation Instructions

ManualsBrandsToro ManualsAttachmentsSpray Gun Kit, Multi-Pro 1200/1250 Turf Sprayer and Workman 200 Spray System

W 2005 by The Toro Company

8111 Lyndale Avenue South

Bloomington, MN 55420-1196

Printed in the USA

Spray Gun Kit

for Multi-Pro

)

1200/1250 Turf Sprayers and Workman

)

200

Spray Systems

Model No. 41133—Serial No. 250000001 and Up

Form No. 3352-886 Rev B

Installation Instructions

Installation

Important You will need to purchase Teflon tape before installing this kit. The tape is used to wrap threads of fittings

before assembly. Threads should be wrapped from left to right, starting at the base and traveling to the tip of fitting (if

looking down the axis of a fitting, tape should be wrapped clockwise from back to front).

Note: A non-petroleum based lubricant, such as vegetable oil, will be required for the installation of this kit.

Note: Determine the left and right sides of the machine from the normal operating position.

Description Qty. Use

Hose hook, single bend

Spray gun bracket

Carriage bolt, 5/16 x 3/4 inch

Flange nut, 5/16 inch

Install the hose hooks

Control valve

Control valve bracket

Phillips screw

Support bracket (for Multi-Pro Sprayers)

Support bracket (for Workman Spray Systems)

Flange-head bolt, 1/4 x 3/4 inch

Flange nut, 1/4 inch

Tee assembly

Pressure gauge

Barbed fitting, 1/2 inch

Retainer

Install the control valve

Hose, long

O-ring

Spray gun

Hose clamp, small

Install the spray gun

Summary of content (8 pages)

PAGE 1
Form No. 3352-886 Rev B Spray Gun Kit for Multi-Pro) 1200/1250 Turf Sprayers and Workman) 200 Spray Systems Model No. 41133—Serial No. 250000001 and Up Installation Instructions Installation Important You will need to purchase Teflon tape before installing this kit. The tape is used to wrap threads of fittings before assembly.
PAGE 2
Preparing the Machine Ensure that the machine is empty of all fluids. If chemicals have been used in the machine, flush the system thoroughly with clean water; refer to your vehicle Operator’s Manual for instructions. 3 Installing the Hose Hooks on a Multi-Pro 1200/1250 Sprayer 1 1. Remove the fasteners securing the right side of the front tank strap (Fig. 1). 2 3 m–8090 Figure 2 1. Front tank strap 2. Hose hook, single bend 1 2.
PAGE 3
2. On a Multi-Pro 1200 Sprayer, disconnect the small red pressure gauge tube from the green tube fitting on top of the supply tee (Fig. 3). To disconnect, press down on the tube fitting while pulling up on the tube. 5. Connect the boom hose you disconnected in step 1 to the open port on the control valve and secure it with the retainer you removed in step 1 (Fig. 5). 6. Remove the 2 bolts securing the supply tee mounting bracket to the vehicle. Retain the fasteners. 3.
PAGE 4
12. Install the support bracket as follows: 13. Connect the large adapter end of the tee assembly to the control valve (Fig. 9). • On a Multi-Pro Sprayer, install the support bracket as shown in Figure 7, using 4 flange-head bolts (1/4 x 3/4 inch) and 4 flange nuts (1/4 inch). 6 6 4 7 5 3 3 2 4 3 1 3 2 1 m–6934 4 Figure 9 Tee assembly shown exploded. m–7821 1. 2. 3. 4. Figure 7 1. Control valve bracket 2. Support bracket 3. Flange-head bolt, 1/4 x 3/4 inch 4.
PAGE 5
Safety Instructions 17. Locate the O-ring in loose parts and lubricate it using a non-petroleum based lubricant such as vegetable oil. Install the O-ring between the long hose and control valve assembly. (Fig. 10). Improper use or maintenance by the operator or owner can result in injury. To reduce the potential for injury, comply with these safety instructions and always pay attention to the safety alert symbol, which means CAUTION, WARNING, or DANGER—“personal safety instruction.
PAGE 6
Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 106-5081 1. Boom spray 2. Hand spray 3. Continuous variable setting Operation 4. Turn the booms off. Warning 5. On Multi-Pro 1250 Sprayers, use the application rate switch to adjust the application rate to the highest setting. Fluid under pressure can penetrate skin and cause injury. 6. Turn the pump on.
PAGE 7
Switching from Hand Spray Mode to Boom Spray Mode 1. Turn the red nob on the face of the control valve to the Boom Spray position. 2. Direct the spray gun nozzle at an area where it is safe to spray, release the trigger lock, and pull the trigger until all remaining fluid is out of the hose, then set the trigger lock. 3. Wrap the hose around the hooks on the tank and place the spray gun in the gun bracket. 4. Return the engine to idle speed and stop the pump.
PAGE 8