Installation Instructions

ManualsBrandsToro ManualsAttachmentsElectric Hose Reel Kit, 2005 and After Multi-Pro 1200/1250 Turf Sprayer

FormNo.3367-828RevA

ElectricHoseReelKit

2005andAfterMulti-Pro

1200/1250TurfSprayer

ModelNo.41135—SerialNo.311000001andUp

InstallationInstructions

Note:Determinetheleftandrightsidesofthemachine

fromthenormaloperatingposition.

Thisattachmentisahoseextendedhandsprayerwithan

electricreelintendedtobeusedbyprofessional,hired

operatorsincommercialapplications.Itisprimarily

designedforsprayinggolfcourseapplications,parks,

sportselds,andoncommercialgrounds.Itisdesigned

toonlybeusedinconjunctionwithmachinesdesignated

bythemanufacturer.

ThisproductcomplieswithallrelevantEuropean

directives,fordetailspleaseseetheseparateproduct

specicDeclarationofConformity(DOC)sheet.

Important:Teontapeisrequiredforthe

installationofthiskit.Thetapeisusedtowrap

threadsofttingsbeforeassembly.Threadsshould

bewrappedstartingatthebaseandtravelingtothe

tipofttingtoensureawaterproofseal.

Important:Anon-petroleumbasedlubricant,such

asvegetableoil,willberequiredfortheinstallation

ofthiskit.

Readthismanualcarefullytolearnhowtooperateand

maintainyourproductproperly.Theinformationin

thismanualcanhelpyouandothersavoidinjuryand

productdamage.AlthoughTorodesignsandproduces

safeproducts,youareresponsibleforoperatingthe

productproperlyandsafely.

YoumaycontactTorodirectlyatwww.Toro.comfor

productandaccessoryinformation,helpndinga

dealer,ortoregisteryourproduct.

Wheneveryouneedservice,genuineToroparts,or

additionalinformation,contactanAuthorizedService

DealerorToroCustomerServiceandhavethemodel

andserialnumbersofyourproductready.

Figure1

illustratesthelocationofthemodelandserialnumbers

ontheproduct.

Figure1

1.Modelandserialnumberplate

ModelNo.

SerialNo.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

Summary of content (12 pages)

PAGE 1
Form No. 3367-828 Rev A Electric Hose Reel Kit 2005 and After Multi-Pro® 1200/1250 Turf Sprayer Model No. 41135—Serial No. 311000001 and Up Installation Instructions Note: Determine the left and right sides of the machine from the normal operating position. illustrates the location of the model and serial numbers on the product. This attachment is a hose extended hand sprayer with an electric reel intended to be used by professional, hired operators in commercial applications.
PAGE 2
Safety • Do not use the hand sprayer if there are any leaks in any hoses, fittings, or other components. • Do not spray near power lines. • Do not drive while spraying with a hand sprayer. • Wear rubber gloves, safety goggles, and a full body protective suit when spraying chemicals with the hand sprayer. • Lightning can cause severe injury or death. If lightning is seen or thunder is heard in the area, do not operate the machine; seek shelter.
PAGE 3
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 Description Qty.
PAGE 4
on the boom frame so that it is in contact with the boom frame pin. 1 Preparing the Machine No Parts Required Procedure 1. Ensure that the machine is empty of all fluids. If chemicals have been used in the machine, flush the system thoroughly with clean water; refer to your vehicle Operator’s Manual for instructions. 2. Disconnect the negative battery terminal from the battery. Figure 2 Boom frame, right side 1. U-bolt 2. Spacer bracket 2 2.
PAGE 5
3. Install the left hose reel support (support without the spray gun holder tube) to the vehicle frame using 2 U-bolts, spacer and 4 flange nuts (3/8 inch) as described in steps 1 and 2. Do not fully tighten the flange nuts to allow for later adjustment. 4. The supports should wrap around the rear end of the tank (Figure 4). Figure 5 1. Hose reel support, right 2. Hose reel support, left 5. Flange nut, 5/16 inch 6. Flange-head bolt, 5/16 x 1-1/2 inch 3. Bolt, 5/16 x 3-1/4 inch 7.
PAGE 6
Figure 6 1. Power wire from the electrical box on the hose reel. 2. Solenoid Figure 7 11. Connect the black wire to a post on the ground terminal block, located under the solenoid. 1. Supply tee 2. Retaining fork 3 2. Multi-Pro 1200 sprayer only: Disconnect the small red pressure gauge tube from the green tube fitting on top of the supply tee (Figure 8). Installing the Control Valve Note: To disconnect, press down on the tube fitting while pulling up on the tube.
PAGE 7
. Install the control valve bracket between the supply tee bracket and the mounting frame (Figure 11) using the fasteners removed previously. Figure 9 Figure 11 Valve assemblies not depicted for clarity 3. Boom supply hose 4. Retaining fork, existing 1. Control Valve 2. Retaining fork, new 1. Tank strap 2. Control valve bracket 3. Supply tee bracket 5.
PAGE 8
15. Install the large plastic nut over the pressure gauge and tee assembly. Install a plastic O-ring and adapter to the assembly as shown in Figure 15. 10. Secure the new control valve to the bracket using two screws (Figure 13). Figure 15 1. Gauge tee assembly 2. Adapter Figure 13 1. Screw 3. O-ring, plastic 4. Large plastic nut 2. Control valve handle, pointing rearward 16. Lubricate the O-ring in the adapter with a non-petroleum based lubricant, such as vegetable oil (Figure 16). 11.
PAGE 9
Tighten the plastic nut on the hose to secure it to the pressure gauge assembly. 2. Connect the free end of the long hose to the fitting on the spray gun (Figure 19). Figure 17 1. Hose, from reel 2. Control valve 3. Gauge assembly 4. O-ring, plastic Figure 19 3. Secure the end of the hose with a small hose clamp. 4 4. Connect the negative battery wire to the battery. 5.
PAGE 10
Operation 4. At the operator’s position, turn the pump on. 5. Increase the engine speed until the pressure gauge reads the desired psi and engage the neutral engine speed lock. WARNING Fluid under pressure can penetrate skin and cause injury. Important: Do not use a pressure setting higher than 150 psi with the hand sprayer. • Keep your body and hands away from nozzles that eject high pressure fluid.
PAGE 11
5. Return the engine to idle speed. 6. Stop the pump. Important: Ensure that you flush the spray gun with fresh clean water during your daily cleaning routine (refer to your sprayer Operator’s Manual). Failure to properly clean the spray gun may degrade the performance and reliability of the hose reel kit and spray gun.
PAGE 12