FORM NO. 95-2160 OPERATOR'S SET-UP & PARTS LIST L P.T.O. KIT J To assure maximum safety, optimum The safety alert symbol means CAUTION, performance, and to gain knowledge of the WARNING, or DANGER — personal product, it Is essential that you or any other safely instruction. Failure to comply with the operator of this equipment read and instruction may result in personal injury. understand the --contents this manual before the tractor engine is ever started.
A\ SAFETY INSTRUCTIONS MAINTENANCE: 7. Before servicing or making any adjustments to the Spreader: A. Stop the tractor and set the parking brake. B. Shut off the engine, disengage P.T.O, drive. C. Disengage ali power and wait until ali moving parts have stopped. D. Keep hands, feet and clothing away from all power driven parts. E. Never stand between the tractor and the Spreader while the engine is running. F.
CONTROLS FLOW CONTROL HANDLE: Opens and closes the regulator discipline Hopper opening, testator stop the flow of material. Pull the Handle forward, toward the operator, fo open the regulator disc. Push the Handle back, away from the operator, to close the regulator disc. FLOW REGULATOR: Determines the rate at which the material flows from the Hopper. The highest number setting (7} on the Regulator Scale, indicates the " largest opening, for maximum flow of material.
SPOUT ARC SETTING: The embossed plus and minus signs on the Spreader housing, indicate the operating arc of the Spreader Spout. {} or MIN = A Spout arc of 38 degrees or MAX = A Spout arc of 58 degrees Adjust the arc of the Spout action as follows: 1. Tums the Implement yoke of the top P.T.0. Shaft by hand, until the arc adjuster appears in the opening in the Spreader, as shown in FIG. 3.
CONTROLS SPREADER CALIBRATION To calibrate the TOR Spreader you must determine the desired rate of flow for the material being applied (in pounds per acre), as specified by the material's manufacturer. To achieve this application rate, first establish the following: 1. The spread width in feet, for the material being applied. NOTE: ~This width will vary depending on the density of the material and the Spout arc setting. 2. Flow rate of material from the Hopper, in pounds per acre.
OPERATING Refer to the charts on page 5 as guidelines to determine the Spout Arc and Flow Regulator settings to achieve the desired rate of application for the material being used. 1. Position the Stop Pin {and Calibration Spacer if necessarily) 1o stop the Flow Control Han die at the desired setting on the Regulator Scale, as described on page 3. 2. Choose the appropriate Spreader Spout and position the “Arc Adjuster as needed for the application rate required, as described on page 5. 3.
SET-UP Mounting Spreader to Tractor: The Toto Spreader is designed for use with almost ail category 1" and *2" Tractors that are fitted with stein 3-point hitch linkage. 1. Switch off Tractor engine and remove the key to be sure the P.7.0. Drive is disengaged. 2. Attach the Spreader to the Tractor's linkage arms. Hitch pins can be turned end for end as desired. Use the category "2 position whenever possible, See FIG, 6. 3.
P.T.0. SHAFT ASS'Y Ref] Part No. Description Oty 1 |95-2159 Shaft Assembly 1 Jo-2161 Repair Kit NOTE: Repair Kits sold | AR las complete sets only, with bushings, center cross, retainers, washers, and June fittings.
The Toto Commercial Products Two Year Limited Warranty The Roberto Company warrants your 1896 or newer Toto Commercial Product {"Product”) purchased after January 1, 1997, to be free from defects in materials or workmanship for the period of time listed below. Hers a warrant able condition exists, Tore will repair the Product at no cost to you including diagnosis, labor , parts, and transportation. This warranty begins on the fete the Product is delivered to the original retail purchaser.
