Installation Instructions

ManualsBrandsToro ManualsSprayersElectric Hose Reel Kit, 2015 and After Multi Pro 1750 Turf Sprayer

FormNo.3391-209RevB

ElectricHoseReelKit

2015andAfterMultiPro

1750TurfSprayer

ModelNo.41159—SerialNo.315000001andUp

InstallationInstructions

Introduction

TheElectricHoseReelKitisadedicatedattachment

foraturfsprayapplicationvehicleandisintended

tobeusedbyprofessional,hiredoperatorsin

commercialapplications.Itisprimarilydesigned

forsprayingonwell-maintainedlawnsinparks,golf

courses,sportselds,andoncommercialgrounds

Readthisinformationcarefullytolearnhowtooperate

andmaintainyourproductproperlyandtoavoid

injuryandproductdamage.Youareresponsiblefor

operatingtheproductproperlyandsafely.

Visitwww.T oro.comformoreinformation,including

safetytips,trainingmaterials,accessoryinformation,

helpndingadealer,ortoregisteryourproduct.

Wheneveryouneedservice,genuineT oroparts,or

additionalinformation,contactanAuthorizedService

DealerorT oroCustomerServiceandhavethemodel

andserialnumbersofyourproductready.Figure1

identiesthelocationofthemodelandserialnumbers

ontheproduct.Writethenumbersinthespace

provided.

Important:Withyourmobiledevice,youcan

scantheQRcodeontheserialnumberdecal(if

equipped)toaccesswarranty,parts,andother

productinformation.

g328087

Figure1

1.Modelandserialnumberlocation

ModelNo.

SerialNo.

Note:Thisproductcomplieswithallrelevant

Europeandirectives.Fordetails,pleaseseethe

DeclarationofIncorporation(DOI)atthebackofthis

publication.

Determinetheleftandrightsidesofthemachinefrom

thenormaloperatingposition.

Important:Teontapeisrequiredforthe

installationofthiskit.Thetapeisusedtowrap

threadsofttingsbeforeassembly.Threads

shouldbewrappedstartingatthebaseand

travelingtothetipofttingtoensureawaterproof

seal.

Important:Anon-petroleumbasedlubricant,

suchasvegetableoil,willberequiredforthe

installationofthiskit.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3391-209*B

Summary of content (16 pages)

PAGE 1
Form No. 3391-209 Rev B Electric Hose Reel Kit 2015 and After Multi Pro® 1750 Turf Sprayer Model No. 41159—Serial No. 315000001 and Up Installation Instructions Introduction Model No. The Electric Hose Reel Kit is a dedicated attachment for a turf spray application vehicle and is intended to be used by professional, hired operators in commercial applications.
PAGE 2
Safety Improper use or maintenance by the operator or owner can result in injury. To reduce the potential for injury, comply with these safety instructions and always pay attention to the safety-alert symbol , which means Caution, Warning, or Danger—personal safety instruction. Failure to comply with the instruction may result in personal injury or death. Read also the safety and operation instructions in the vehicle Operator's Manual. • Do not aim the hand sprayer at people or animals.
PAGE 3
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 Description Qty.
PAGE 4
1 4. Secure a small R-clamp to the carriage bolt using a flange nut (3/8 inch) as shown in Figure 2. 5. Route the hose reel end of the wiring harness through the R-clamp as shown in Figure 2. Preparing the Machine No Parts Required Procedure 1. Empty the sprayer tank. 2. Clean and rinse the sprayer tank; refer to the Operator's Manual for your machine. 3.
PAGE 5
g329220 Figure 4 1. Panel plug (round) 3. 4. Plug the next connector into the relay (Figure 7), and mount the relay to the outer hole on the frame near the existing relays. 5. Connect the fusable link to the red wire attached to the positive (+) battery terminal (Figure 7). 6. Connect the negative (-) connection on the wire harness to the negative (-) battery terminal. 7. Connect the far end of the wiring harness to the fuse block ground (Figure 7). 2.
PAGE 6
2. 3 Attach the swivel plate to the bottom of the hose reel using 4 carriage bolts and 4 flange nuts (3/8 inch) (Figure 9). Mounting the Hose Reel Parts needed for this procedure: 1 Hose-reel frame 10 Bolt (5/16) 10 Flange nut (5/16 inch) 1 Swivel plate 1 Hose reel 4 Large carriage bolt 4 Flange nut (3/8 inch) 1 Handle 1 Mud shield 1 Spring clip 2 Locknut 1. Hose reel 2. Swivel plate 2 Small carriage bolt 3.
PAGE 7
g023326 Figure 11 1. Bolts (5/16) 3. Handle 2. Mud shield 6. 7. Attach the mud shield and handle to the swivel plate using the bolts installed in step 5 and 4 flange nuts (5/16 inch) (Figure 11). g023325 Figure 12 Secure the top of the mud shield to the handle using 2 self-tapping screws (Figure 12). 1. Bolt (5/16 inch) 4. R-clamp (large) 2. Spray gun bracket 5. Flange nut (5/16 inch) 3. Spacer 6. Self-tapping screw 8. Attach the spray gun holder to the mud shield as shown in Figure 12. 9.
PAGE 8
g028237 g028394 Figure 13 1. Actuator Figure 15 3. Stem port 1. Boom valve cluster 2. Retainer 2. Remove the actuator from the manifold valve. 3. Remove the retainers holding the boom bypass valve cluster assembly, end cap, and the fitting and hose assembly as shown in Figure 14. 6. Adjust the left and right knobs to the previous settings. 5 Note: You will not use the male cap, but keep the O-ring that is on the cap.
PAGE 9
g329235 Figure 16 2. g329237 Figure 19 1. Valve mount Install the valve-mount bracket onto the valve-mount frame using 2 flange-head bolts (1/4 x 0.625 inch) as shown in Figure 17. 2. Bolt (M6) 6. Secure the shut-off valve to the boom valve with the previously removed o-ring and retainer (Figure 20). 7. Install the cap (1/2 inch), o-rings, fitting, and hose assembly onto the shut-off valve using the retainers previously removed as shown in Figure 20. g329236 Figure 17 1. Valve-mount frame 3.
PAGE 10
g028395 Figure 22 1. Tank-supply hose 16. g329241 Figure 21 1. Gasket 4. Coupler 2. 90-degree fitting 5. Control valve 3. Gasket clamp 6. Hose-reel supply hose 10. Install the control valve assembly as shown in Figure 21. 11. Install the coupler into the open port on the 90-degree fitting (Figure 21). Note: The cap can be discarded. 12. Connect the pressure-sense hose to the coupler. 13. Connect the hose-reel supply hose to the control valve using a hose clamp. 14.
PAGE 11
6 Connecting the Spray Hose Long hose with fitting 1 Spray gun 1 Plastic hose clamp 5. Connect the negative battery wire to the battery. 6. Press the hose wind button, and carefully guide the hose onto the reel moving the hose from side to side to evenly distribute the hose. Hands, loose clothing, long hair, and jewelry could get caught in the hose and reel while rewinding and cause injury. • Keep your hands clear of the reel and hose while it is rewinding.
PAGE 12
Switching from Boom Spray Mode to Hand Spray Mode 1. CAUTION Hands, loose clothing, long hair, and jewelry could get caught in the hose and reel while rewinding and cause injury. Stop the machine, turn the booms off, and set the parking brake. • Keep your hands clear of the reel and hose while it is rewinding. • Do not wear loose clothing or jewelry and tie up long hair. WARNING Driving while using the hand sprayer can cause loss of control, resulting in injury or death.
PAGE 13
Notes:
PAGE 14
Declaration of Incorporation The Toro Company, 8111 Lyndale Ave. South, Bloomington, MN, USA declares that the following unit(s) conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain Toro models as indicated on the relevant Declarations of Conformity. Model No. 41159 Serial No.
PAGE 15
Toro General Commercial Product Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
PAGE 16