Form No. 3358-906 Rev C Multi-Pro® 1250 Turf Sprayer Model No. 41179—Serial No. 280000001 and Up To register your product or download an Operator's Manual or Parts Catalog at no charge, go to www.Toro.com.
Warning 1 CALIFORNIA Proposition 65 Warning The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. Important: This engine is not equipped with a spark arrester muffler. It is a violation of California Public Resource Code Section 4442 to use or operate the engine on any forest-covered, brush-covered, or grass-covered land. Other states or federal areas may have similar laws. G001788 Figure 1 1.
1 Installing the Anti-siphon Fill Receptacle ...................................................... 14 2 Installing the Spray Pro Monitor....................... 14 3 Completing the Setup: Learning more about your product................................................... 15 Product Overview ...................................................... 16 Controls ............................................................. 17 Specifications ..................................................... 23 Operation.......
Chemical Safety Safety Improper use or maintenance by the operator or owner can result in injury. To reduce the potential for injury, comply with these safety instructions and always pay attention to the safety alert symbol, which means CAUTION, WARNING, or DANGER—personal safety instruction. Failure to comply with the instruction may result in personal injury or death. Chemical substances used in the spray system may be hazardous and toxic to you, bystanders, animals, plants, soils or other property.
• Properly dispose of unused chemicals and chemical containers as instructed by the chemical manufacturer and your local codes. • Chemicals and fumes in the tanks are dangerous; never enter the tank or place your head over or in the opening. If the machine does not function correctly or is damaged in any way, do not use the sprayer. Make sure that the problem is corrected before the sprayer or attachment is operated.
through standing water deep enough to get the brakes wet, they will not work well until they are dry. After driving through water, you should test the brakes to make sure they work properly. If they do not, drive slowly while putting light pressure on the brake pedal. This will dry the brakes out. – Avoid sudden stops and starts. Do not go from reverse to forward or forward to reverse without first coming to a complete stop. – Slow down before turning.
Loading under pressure can penetrate skin and cause injury requiring surgery within a few hours by a qualified surgeon or gangrene may result. The weight of the cargo can change the sprayer center of gravity and sprayer handling. To avoid loss of control and personal injury, follow these guidelines: • If major repairs are ever needed or assistance is required, contact an Authorized Toro Distributor.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 104-7628 1. Read the Operator’s Manual. 100-8386 1. Fuel 2. Empty 100-8458 1. Machine speed 2. To set the machine to a slow speed, reduce pressure on the accelerator and pull up on the speed limiter. 3. To set the machine to a fast speed, press the accelerator pedal and push down on the speed limiter. 100-8619 1.
100-8470 1. 2. 3. 4. Engine—stop Engine—run Engine—start Headlights 5. 6. 7. 8. Neutral engine speed lock Engage On Off 100-8454 1. Read the Operator’s Manual for information on the transmission. 2. To start the engine, sit on the operator’s seat, press the brake, set the range selector to Neutral, turn the ignition key to Engine-start, set the range selector to the desired gear, release the brake and parking brake, and press the accelerator pedal to the desired speed. 3.
6-5016 1. Warning—read the Operator’s Manual. 2. Electric shock hazard, overhead power lines—stay away from overhead power lines. 3. Crushing hazard, boom—keep bystanders a safe distance from the machine. 93-0688 1. Warning—read the Operator’s Manual. 2. Caustic liquid/chemical burn and toxic gas inhalation hazards—wear hand, skin, eye, and respiratory protection. 110-5240 1. Warning—read the Operator’s Manual and receive training before operating. 2.
0-5143 106-5051 1. Warning—read the Operator’s Manual. 2. Tipping Hazard—drive slowly over rough terrain and when turning. 3. Falling and arm/leg injury hazards—do not carry passengers and keep arms and legs inside of the vehicle at all times. 4. To stop the engine, press the brake, move the range selector to Neutral, set the parking brake, release the brake pedal, turn the ignition key to Engine-stop, and remove the key. 1.
108-3252 1. Warning—read the Operator’s Manual. 2. Torque lug nuts to 55-65 ft-lb (75-88 N·m). 108-3699 1. 30 amp fuse, left boom 6. actuator 2. 30 amp fuse, right boom 7. actuator 3. 15 amp fuse, foam marker 8. 4. Empty 9. 5. 30 amp fuse, power 10. 10 amp fuse, headlights 5 amp fuse, cruise control 20 amp fuse, spray system Fuse panel Read the Operator’s Manual for more information. 104-8939 1. Engine oil level (dipstick) 2. Engine oil filter 3. Transaxle/hydraulic fluid level (dipstick) 5.
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 Description Qty.
4. Lock the adapter into place by swinging the levers toward the adapter and then secure them with the hairpin cotters (Figure 3). 1 5. Install the anti-siphon hose through the large opening on the bracket and onto the barbed end of the 90 degree elbow fitting (Figure 3). Installing the Anti-siphon Fill Receptacle Important: Do not lengthen the hose to allow contact with the tank fluids.
Figure 7 Figure 5 1. Spray Pro monitor 2. Bracket 1. Connectors from the sprayer 3. Flange-head bolts, 1/4 x 3/4 inch 4. Knob 2. Connectors from the monitor 3 3. Loosely install the 2 carriage bolts, rubber washers, and knobs on the bracket as illustrated in Figure Figure 5 and Figure 6. Completing the Setup: Learning more about your product. Note: Install the carriage bolts and rubber washers inside of the bracket and the knobs on the outside. Parts needed for this procedure: Figure 6 1.
Product Overview Figure 8 3. Fresh water tank 4. Fuel tank 1. Operator’s position 2. Headlight 7 5. Chemical tank 6. Anti-Siphon Receptacle 3 2 7. Tank lid 6 8 1 G002151 5 4 Figure 9 1. Pedals 2. Rinse tank 5. Battery 6. Pump pressure dampener 3. Chemical tank 4. Pump 16 7. Agitation control valve 8.
Controls Figure 10 1. Steering wheel 2. Spray-Pro monitor 3. Speed limiter 7. Parking brake 8. Master boom foot switch 9. Range Selector 4. Choke 5. Sprayer controls 6. Rate lockout switch 10. Voltmeter 11. Hour meter 12. Vehicle controls Accelerator Pedal The accelerator pedal (Figure 11) gives you the ability to vary ground speed of the sprayer. Pressing the pedal increases ground speed. Releasing the pedal will slow the sprayer and the engine will idle.
Range Selector The range selector, located to the left of the seat, has 5 positions: 3 forward speeds, Neutral, and Reverse (Figure 14). The engine will start only when the range selector is in the Neutral position. You must also fully press the brake with the sprayer stopped to change ranges. Important: Do not shift out of or change ranges while the vehicle is moving. Attempting to change ranges while the vehicle is moving can damage the transmission.
Voltmeter Boom Switches The voltmeter (Figure 14) indicates the level of charge in the battery. When the battery is fully charged, the voltmeter will read in the center of the dial when the key is in the Run position with the engine off. When the engine is running the voltmeter needle should be to the right. The boom switches are located at the front of the control panel to the right of the seat (Figure 16).
Rate Lockout Key Switch The rate lockout key switch is located on the control panel to the right of the seat (Figure 16). Turn the key counterclockwise to the locked position to disable the application rate switch, thereby keeping anyone from accidentally changing the application rate. Turn the key clockwise to the unlocked position to enable the application rate switch. Important: Do not attempt to move the range selector while the rate lockout key is engaged.
Pressure Gauge The pressure gauge is located to the right of the tank (Figure 18). This gauge shows the pressure of the fluid in the system in psi and kPa. Use the gauge to adjust the by-pass valves whenever you change nozzles. Anti-siphon Fill Receptacle To the front of the tank cover is a hose receptacle with a threaded fitting, a 90 degree barbed fitting, and a short hose which you can direct toward the tank opening.
Spray Pro™ Monitor The monitor has an LCD screen that displays the data you select, a selection dial, and 4 buttons for calibrating the monitor (Figure 19). The Spray Pro monitor displays and monitors various system performance data such as vehicle speed and application rates. It does not control the application rate. Figure 19 1. LCD screen 2. Selection dial 3. Total area 4. Speed 5. Units of measure 6. Application rate 7. Sub Area 8. Distance 9. Sub volume 10. Total volume 11.
Specifications setting, without affecting the Total Volume display. If you press the Reset calibration button, the Sub Area resets. Note: Specifications and design are subject to change without notice. • Total Volume Displays the total volume in US gallons (US and TURF) or liters (SI) that you have applied since you last pressed the Reset calibration button for this setting.
Operation Check the Tire Pressure Note: Determine the left and right sides of the machine from the normal operating position. Check the tire pressure every 8 hours or daily to ensure proper levels. Fill the tires to 18 psi (124 kPa). Also, check the tires for wear or damage. Think Safety First Add Fuel Please carefully read all of the safety instructions and decals in the safety section. Knowing this information could help you or bystanders avoid injury.
In certain conditions during fueling, static electricity can be released causing a spark which can ignite the gasoline vapors. A fire or explosion from gasoline can burn you and others and can damage property. • Always place gasoline containers on the ground away from your vehicle before filling. • Do not fill gasoline containers inside a vehicle or on a truck or trailer bed because interior carpets or plastic truck bed liners may insulate the container and slow the loss of any static charge. Figure 21 1.
Driving the Sprayer Starting the Engine 1. Sit in the Operator’s seat, insert the key into the ignition switch, and rotate the key clockwise to the Run position. 2. Press the brake and move the range selector to the Neutral position. 3. Ensure that the pump switch is in the Off position. Figure 22 4. If the engine is cold, pull the choke knob up. 1. Speed limiter knob 2. Speed limiter button Important: Do not use the choke if the engine is warm. 5.
Filling the Fresh Water Tank • Vary the sprayer speed during operation. Avoid fast starts and quick stops. Always fill the fresh water tank with clean water before handling or mixing any chemicals. • Refer to the Maintenance section for any special low hour checks. The fresh water tank is located at the front, left side of the chemical tank (Figure 23). It supplies a source of fresh water for you to wash chemicals off of your skin, eyes, or other surfaces in the case of accidental exposure.
The tank cover is located in the center of the top of the tank (Figure 24). To open it, turn the front half of the cover counterclockwise and swing it open. You can remove the strainer inside for cleaning. To seal the tank, close the cover and rotate the front half clockwise. 2 1 install your booms and nozzles and before using the sprayer for the first time, adjust the boom bypass valves so that the pressure and application rate remains the same for all booms when you turn one or more booms off.
whenever you have solution in the tank. For agitation to work, the pump must be on and the engine must be running above an idle. If you stop the vehicle and need agitation on, place the range selector in the Neutral position, set the parking brake, press the accelerator pedal to the floor, turn on the pump, and turn the neutral engine speed lock On. the range selector in neutral and use the neutral engine speed lock to hold the engine speed up to keep the agitation running.
2 2. Locate the tank drain valve on the left side of the machine (Figure 26). The valve is on the frame in front of the fuel tank. 3 1 Figure 26 1. Tank drain handle Open the valve to drain any unused material from the tank and dispose of it according to local codes and the material manufacturer’s instructions (Figure 27). After draining, remove the lynch pin on the bracket securing the drain valve to the machine and let the valve rest on the ground .
12. Set the master boom switch to the Off position, set the pump switch to the Off position, and stop the engine. 13. Repeat steps 4 through 12 at least 2 more times to ensure that the spray system is fully cleaned. On the last cycle, run the last few gallons of water through the drain valve to clear the drain tubing. 14. Clean the strainer; refer to Cleaning the Suction Strainer in the Cleaning section. Important: If you used wettable powder chemicals, clean the strainer after each tank. 15.
Calibrating the Spray Pro Monitor Figure 28 1. 2. 3. 4. 5. LCD screen Selection dial Total area Speed Units of measure 6. 7. 8. 9. 10. Application rate Sub Area Distance Sub volume Total volume 11. 12. 13. 14. 15. The Spray Pro monitor has a calibration mode that allows you to change various settings to customize the display and calibrate the monitor to your needs.
1. Stop the sprayer and set the parking brake. 2. Set the master boom switch to the Off position. The monitor displays “HOLD”. 3. Press and hold the Calibrate button until the monitor displays “CAL HOLD” and the red light on the monitor illuminates. 4. Turn the selection dial to the Select Units (or Units of Measure) position. 5. Use the Increase or Decrease calibration buttons to select desired units of measure. 6. Press the Calibrate button until the red light turns off.
for the nozzles you installed on the booms (typically 40 psi/2.75 bar). 14. With the selection dial set to the Distance position, press and hold the Calibrate button until the monitor displays “CAL HOLD” and the red light on the monitor illuminates. 10. Record the reading on the pressure gauge. 11. Turn off one of the booms using the appropriate boom switch. The display will alternate between the distance value (“HOLD” shown) and the speed calibration value (“CAL HOLD” shown). 12.
Adjusting the Air Pressure in Dampener 1. Affix a tow line to the frame. 2. Put the range selector in the Neutral position and release the parking brake. The air pressure in the dampener on the pump is set at 15 psi (1 bar) by the manufacturer. This is recommended for nozzle spray pressures between 20 psi (1.3 bar) and 45 psi (3 bar). If different nozzle pressures are required, set pressure dampener at pressures indicated. Nozzle Dampener 40 psi/2.7 bar 12–14 psi/0.8–0.9 bar 3.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 8 hours • • • • After the first 50 hours • Change the engine oil. Before each use or daily • • • • Torque the wheel lug nuts. Check the drive belt. Check the steering pump belt tension. Replace the hydraulic filter. Clean the engine rotating screen. Check the engine oil.
Daily Maintenance Checklist Duplicate this page for routine use. Maintenance Check Item For the week of: Mon. Tues. Wed. Check the brake and parking brake operation. Check the gear shift/neutral operation. Check the fuel level. Check the engine oil level. Check the transaxle oil level. Inspect the air filter. Inspect the engine cooling fins. Check any unusual engine noises. Check any unusual operating noises. Check the tire pressure. Check for fluid leaks. Check the instrument operation.
If you leave the key in the ignition switch, someone could accidently start the engine and seriously injure you or other bystanders. Remove the key from the ignition and disconnect the wire(s) from the spark plug(s) before you do any maintenance. Set the wire(s) aside so that it does not accidentally contact the spark plug(s). Figure 32 Service locations 1. Engine oil level (dipstick) 2. Engine oil filter 3. Transaxle/hydraulic fluid level (dipstick) 5. Hydraulic strainer 6. Gear box fluid level 7.
Lubrication Greasing the Sprayer Service Interval: Every 50 hours—Lubricate the pump. Every 100 hours/Yearly (whichever comes first)—Lubricate all grease fittings. Grease Type: No. 2 General Purpose Lithium Base Grease Figure 33 1. Front jacking points 1. Wipe the grease fitting clean so that foreign matter cannot be forced into the bearing or bushing. The jacking point at the rear of the sprayer is on the rear frame support, between the angle welds (Figure 34). 2.
Figure 38 Pump drive, four, one each side Figure 36 At the wheels, three on each side 1. Grease point 1. Grease point Figure 39 Drive axel at engine, five, one each side and slip joint Figure 37 Steering rods 1. Grease point 1. Grease point Figure 40 Drive axel at transmission 1.
Engine Maintenance Checking the Air Intake Screen Service Interval: Before each use or daily—Clean the engine rotating screen. Every 100 hours—Clean the engine rotating screen (more often in dusty, dirty conditions). Check and clean as necessary the air intake screen on the front of the engine before each use or daily. Servicing the Air Cleaner Foam Element: Clean and oil after every 25 operating hours, or yearly, whichever occurs first.
4. Loosen the knob on the air cleaner cover and remove the cover (Figure 42). 5. Carefully slide the foam element off the paper element (Figure 42). 6. Unscrew the cover nut and remove the cover and paper element (Figure 42). Figure 44 Cleaning the Foam Element 1. Paper element Service Interval: Every 25 hours/Yearly (whichever comes first)—Clean and oil the foam air cleaner (more often in dusty, dirty conditions). 2.
2. Remove the dipstick and wipe it with a clean rag (Figure 45). Insert the dipstick into the tube and make sure it is seated fully. Remove the dipstick and check the oil level. Figure 46 1. Oil drain plug 6. When the oil has drained completely, replace the drain plug and torque it to 10 ft-lb (13.6 N-m). 7. Dispose of the used oil at a certified recycling center. 8. Slowly pour approximately 80% of the specified amount of oil into the oil filler tube (Figure 45). 9. Check the oil level. 10.
6. Fill the crankcase with the correct type of new oil; refer to Changing the Engine Oil, steps 8 through 10. coating on the insulator usually means the air cleaner is dirty. 7. Dispose of the used oil filter at a certified recycling center. Important: Do not clean the spark plugs. Always replace a spark plug when it has a black coating, worn electrodes, an oily film, or cracks. Changing the Spark Plugs 2.
Fuel System Maintenance Electrical System Maintenance Replacing the Fuel Filter Fuses Service Interval: Every 100 hours—Replace the fuel filter. There are 2 fuse blocks and 1 empty slot in the electrical system. They are located beneath the seat (Figure 51). Every 400 hours/Yearly (whichever comes first)—Inspect the fuel lines. 1. Set the parking brake, stop the pump, stop the engine, and remove the ignition key. 2. Release the latch on the back of the seat and lift the seat forward. 3.
Removing the Battery 1. Position the sprayer on a level surface, set the parking brake, stop the pump, stop the engine, and remove the ignition key. Battery terminals or metal tools could short against metal sprayer components causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury. 2. Loosen the knobs on the sides of the battery box and remove the battery cover (Figure 52).
Storing the Battery If the machine will be stored for more than 30 days, remove the battery and charge it fully. Either store it on the shelf or on the machine. Leave the cables disconnected if it is stored on the machine. Store the battery in a cool atmosphere to avoid quick deterioration of the charge in the battery. To prevent the battery from freezing, make sure it is fully charged. Battery electrolyte contains sulfuric acid which is a deadly poison and causes severe burns.
Drive System Maintenance Maintaining the Primary Drive Clutch Figure 54 Service Interval: Every 400 hours/Yearly (whichever comes first)—Clean and lubricate the primary drive clutch. 1. Cover 2. Bolts 1. Stop the engine, remove the key, and set the parking brake. 2. Raise the front end of the sprayer and support it on jack stands. The dust in the clutch will become airborne and could damage your eyes or you could inhale it causing breathing difficulties.
Check the tire pressure every 8 hours or daily to ensure proper levels. Fill the tires to 18 psi (124 kPa). Also, check the tires for wear or damage. Check the wheels to ensure that they are mounted securely after the first 8 operating hours and then every 100 hours thereafter. Torque the front bolts to 50-55 ft-lb (68-74 N-m) and the rear lug nuts to 40-60 ft-lb (54-81 N-m). Check the tire condition at least every 100 hours of operation.
Brake Maintenance Inspecting the Brakes Service Interval: Every 100 hours Checking the Brake Fluid The brakes are a critical safety component of the sprayer. Inspect them as follows: The brake fluid reservoir is shipped from the factory filled with DOT 3 brake fluid. Check the level before starting the engine each day. • Inspect the brake shoes for wear or damage. If the lining (brake pad) thickness is less than 1/16 inch (1.6 mm), replace the brake shoes.
Belt Maintenance 2. Loosen the steering pump mounting bolts (Figure 62). Servicing the Drive Belt Checking the Drive Belt Service Interval: After the first 8 hours Every 200 hours 1. Position the sprayer on a level surface, set the parking brake, move the range selector to the Neutral position, stop the pump, stop the engine, and remove the ignition key. 2. Rotate and inspect the drive belt for excessive wear or damage. Replace the belt if necessary. Figure 62 1. Steering pump belt 3.
Hydraulic System Maintenance 2. Place a drain pan under the drain plug of the reservoir. 3. Remove the drain plug from the side of the reservoir and let the hydraulic fluid flow into the drain pan (Figure 64). Checking the Transaxle/Hydraulic Fluid Service Interval: Every 200 hours 1. Position the sprayer on a level surface, set the parking brake, stop the pump, stop the engine, and remove the ignition key. 2. Remove the transaxle dipstick and wipe it with a clean rag (Figure 63). Figure 64 1.
Spray System Maintenance Important: Use only the hydraulic fluids specified. Other fluids could cause system damage. 12. Start the engine and drive the sprayer to fill the hydraulic system. Recheck the oil level and replenish it, if required. Chemical substances used in the spray system may be hazardous and toxic to you, bystanders, animals, plants, soils or other property.
Pump Maintenance Inspecting the Pump Service Interval: Every 400 hours/Yearly (whichever comes first)—Inspect the pump diaphragm and replace if necessary. (see an Authorized Toro Service Distributor) Every 400 hours/Yearly (whichever comes first)—Inspect the pressure dampener bladder and replace if necessary. (see an Authorized Toro Service Distributor) Every 400 hours/Yearly (whichever comes first)—Inspect the pump check valves and replace if necessary.
Cleaning wheel assembly into the body in any other orientation. 6. Install the retaining cap. Cleaning the Flowmeter 7. Connect the wire to the flowmeter. Service Interval: Every 400 hours/Yearly (whichever comes first) Cleaning the Suction Strainer Occasionally, the flowmeter may need to be cleaned to remove an obstruction. Service Interval: Before each use or daily (more often when using wetable powders) Note: Make sure the pump is off when performing this procedure. 1.
Storage G. Dispose of fuel properly. Recycle as per local codes. 1. Position the sprayer on a level surface, set the parking brake, stop the pump, stop the engine, and remove the ignition key. 2. Clean dirt and grime from the entire machine, including the outside of the engine’s cylinder head fins and blower housing. Important: Do not store stabilizer/conditioned gasoline over 90 days 11. Remove the spark plugs and check their condition; refer to Changing Spark Plugs in the Engine Maintenance section.
Troubleshooting Troubleshooting the Engine and Vehicle Problem The starter does not crank. Possible Cause 1. The range selector is in a gear other than Neutral. 1. Press the brake pedal and move the range selector to the Neutral position. 2. The electrical connections are corroded or loose. 3. A fuse is blown or loose. 4. The battery is discharged. 5. The safety interlock system is malfunctioning. 6. A broken starter or starter solenoid. 2. Check the electrical connections for good contact. 3.
Problem The engine will not idle. Possible Cause Corrective Action 1. The fuel tank vent is restricted. 1. Replace the fuel cap. 2. Dirt, water, or stale fuel is in the fuel system. 3. A spark plug is damaged or broken. 4. Carburetor idle passages are plugged. 8. The air cleaner element is dirty. 2. Drain and flush the fuel system; add fresh fuel. 3. Replace the spark plug. 4. Contact your Authorized Service Dealer. 5. Contact your Authorized Service Dealer. 6. Contact your Authorized Service Dealer.
Troubleshooting the Spray System Problem A boom section does not spray. Possible Cause Corrective Action 1. The electrical connection on the boom valve is dirty or disconnected. 1. Turn the valve off manually. Disconnect the electrical connector on the valve and clean all leads, then reconnect it. 2. Blown fuse 2. Check the fuses and replace them as necessary. 3. Repair or replace the hose. 4. Adjust the boom by-pass valves. 3. Pinched hose 4. A boom by-pass valve is improperly adjusted. 5.
Problem The Distance is inaccurate. The monitor does not display Application Rate or Total Volume. The Total Volume is inaccurate. Possible Cause Corrective Action 1. The speed sensor is not calibrated correctly. 1. Calibrate the speed sensor. 2. The speed sensor is damaged. 2. Contact your Authorized Service Dealer. 1. The monitor cable is loose. 1. Connect the monitor cable. 2. The flow meter is dirty or clogged. 3. The flow meter is not calibrated correctly. 4. The flow meter is damaged. 2.
Schematics Electrical, vehicle (Rev.
Electrical, spray system (Rev.
Hydraulic (Rev.
AGITATION CONTROL VALVE TIO SUC N SUCTION DAMPENER N TIO SUC 1203 DIAPHRAGM PUMP ION TAT I AG Flow Diagram (Rev.
Notes: 65
Notes: 66
Notes: 67
Toro General Commercial Products Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial Product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).
