Installation Instructions

ManualsBrandsToro ManualsAttachmentsOperator Enclosure, Multi-Pro 1100

Model No. 41183-90001 & UP

©The TORO Company - 1999

FORM NO.93-6202

OPERATOR ENCLOSURE

for the MULTI-PRO

1100 Vehicle

SET-UP &

PARTS MANUAL

NOTE: AN ASSISTANT MAY BE NEEDED IN

THE ASSEMBLY OF THE OPERATOR

ENCLOSURE.

INSERT ANCHORS HAVE BEEN PROVIDED IN

THE ROPS BAR TO ALLOW INSTALLATION OF

THE OPERATOR ENCLOSURE.

REFER TO THE ILLUSTRATED PARTS LIST FOR

DETAILS OF PARTS USED IN ASSEMBLING

THE OPERATOR ENCLOSURE.

NOTE: "RIGHT", "LEFT", "FRONT", AND "REAR"

ARE REFERENCED WHILE SEATED IN THE

OPERATORS POSITION.

SET-UP INSTRUCTIONS

1. Install the ROPS kit as per the instructions

provided with that kit. Leave bolts loose until

operator enclosure is completely installed.

2. Locate and remove the Blower Wiring

Harness and the (2) 5/16" grommets from the

parts bags.

3. Remove the wire loom and ring terminal end

of the Wiring Harness by disconnecting the

connector located approx. 6" inside the wire

loom. This section will be reconnected later. See

FIG. 1.

1. Grommet 5. Female Bullet

2. Male Bullet Connector Connector

3. Blower Wiring Harness 6. Frame Cross Tube

4. L.H. ROPS Bar 7. Sta- Strap

FIG. 1

4. Slide a 5/16" grommet on the Blower Wire

Harness by sliding it over the Male Bullet

Connector, along the wire to the Female Bullet

Connector at the other end.

5. Beginning with the end of the Wiring Harness

having the male connector, thread the Wiring

Harness down through the left hand ROPS Bar.

6. Push the Grommet into the top of the ROPS

Bar. Slide a 5/16" grommet over the Male Bullet

Connector coming out of hole at the bottom of

the ROPS Bar. Push Grommet into place.

7. At the bottom of the ROPS Bar, reconnect the

portion of the Wiring Harness removed in Step 3.

8. Route Wiring Harness back towards engine

compartment and through hole in the Frame

Cross Member. Secure Wiring Harness to Clutch

Pivot Bracket with the Sta-Strap.

9. From the hole in the Frame Cross Member

route the Wiring Harness through the hole in the

Engine Cross Member and up to Starter Solenoid.

Attach 5/16" Ring Terminal to (+) positive post on

the Starter Solenoid. See FIG. 2.

1. Starter Solenoid 2. Engine Cross Member

Connection

FIG. 2

1596

1597

Summary of content (8 pages)

PAGE 1
FORM NO.93-6202 Model No. 41183-90001 & UP SET-UP & PARTS MANUAL OPERATOR ENCLOSURE for the MULTI-PROTM 1100 Vehicle NOTE: AN ASSISTANT MAY BE NEEDED IN THE ASSEMBLY OF THE OPERATOR ENCLOSURE. REFER TO THE ILLUSTRATED PARTS LIST FOR DETAILS OF PARTS USED IN ASSEMBLING THE OPERATOR ENCLOSURE. INSERT ANCHORS HAVE BEEN PROVIDED IN THE ROPS BAR TO ALLOW INSTALLATION OF THE OPERATOR ENCLOSURE. NOTE: "RIGHT", "LEFT", "FRONT", AND "REAR" ARE REFERENCED WHILE SEATED IN THE OPERATORS POSITION.
PAGE 2
NOTE: IF YOU HAVE COMPLETELY INSTALLED THE ROPS UNIT ON YOUR VEHICLE YOU WILL NEED TO REMOVE THE ROPS CROSS BAR AND SEAT BELT ASSEMBLY BEFORE INSTALLING THE ENCLOSURE. 10. Remove the Enclosure Cover and Blower from the shipping carton. 11. Remove the (3) 1/4" flange hd. bolts that secure the Blower Assembly to the front of the Enclosure Cover and remove Blower. Set Blower and flange bolts aside for future installation. 12. Remove the (4) 3/8" x 3/4" flange hd.
PAGE 3
20. Slide the Front Window up until the top Window Trim meets the lower flange of the Enclosure Cover. Tighten mounting bolts securely. 21. Slide the Blower Assembly forward until Blower Flange meets with top of Front Window. Slide ROPS Cross Bar as far forward as it will go and tighten the (6) 1/4" flange hd. cap screws. 22. Loosely mount the Rear Window and (2) Window Clamps to rear ROPS Bar by screwing (4) 1/4" x 3/4" flange hd. bolts into the ROPS bar.
PAGE 4
28. Install the Inner Door Latch Assembly through the 5/16" hole in Door with the flatwasher between latch and glass. See FIG. 9. 32. Loosely mount the (2) Door Catches to the ROPS with the (4) 1/4" x 3/4" flange hd. bolts re moved is step 31. 33. With the Door closed against the Front ROPS Bar, tighten the mounting bolts securing the Door Catches to the Front ROPS Bar. 34.
PAGE 5
IMPORTANT: DO NOT USE KNIVES, BLADES, OR SCRAPERS TO REMOVE THE PROTECTIVE PAPER AS THIS WILL SCRATCH OR CUT THE DOORS AND WINDOW! 40. Check the operation of the blower assembly and make certain all fasteners are tightened securely. NOTE: WHEN USING AN OPEN TRAILER TO TRANSPORT A MULTI-PRO EQUIPPED WITH THIS OPERATOR ENCLOSURE, ALWAYS USE HOLD-DOWN CLAMPS PROVIDED, TO HOLD DOORS SHUT. TO INSTALL HOLD-DOWN CLAMPS: 41. Loosen the (4) 1/4" x 3/4" flange hd.
PAGE 6
1608 6
PAGE 7
ENCLOSURE Ref Part No. Description Qty Ref Part No. Description Qty 1 92-3814 Charcoal Filter 1 32 92-3908 Door Glazing - Top 2 2 92-3902 Foam Strip 1/8 x 1/2 x 4" 2 33 93-1075 Door 2 3 92-3903 Foam Strip 1/8 x 1/2 x 22-7/8" 2 34 92-3776 Door Trim - Bottom 2 4 92-3806 Enclosure Cover 1 35 92-3910 Door Glazing - Bottom 2 5 32153-1 Hex Nut No. 10-24 4 36 92-3775 Door Trim - Front 2 6 92-3904 Flange Hd.
PAGE 8
1609 BLOWER Ref Part No. Description Qty 1 11 92-0251 Fuse Holder 1 Flange Hd.