Form No. 3448-145 Rev A CE Kit Multi Pro® 1750 Turf Sprayer Model No. 41202 Installation Instructions Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal104-8904 104-8904 1. Grasp the boom here. decal119-9434 119-9434 1. Tank contents © 2021—The Toro® Company 8111 Lyndale Avenue South Bloomington, MN 55420 Register at www.Toro.com.
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 7 Description Use Qty.
1 Installing the Rear Light Parts needed for this procedure: 1 Rear light 1 Bracket 2 Nut (5/16 inch) 2 Bolt (5/16-18 x 3/4 inch) 2 g025026 Figure 2 Stamped-steel nut 1. Rear-light 3. Stamped-steel nut 2. Rear-light bracket Procedure 1. Align the holes of the rear-light bracket with the 2 holes in the boom-frame channel. 2. Secure the bracket to the frame with the 2 bolts (5/16 x 3/4 inch) and 2 locknuts (5/16 inch) as shown in Figure 1.
g024691 Figure 3 1. Horn assembly 3. Flange nut (5/16-18) 2. Hex-head screw (5/16-18 x 3/4 inch) 3 Routing the Wiring Harness Parts needed for this procedure: 1 Wire harness Figure 4 shows an outline of the kit wire-harness routing on the machine.
Routing the Wiring Harness to the Side Console 1. Route the wire harness through the front of the seat shroud (Figure 5). g024712 Figure 7 1. Cover 2. Bolts g024709 Figure 5 1. Opening in the front of the seat shroud 2. Route the wire harness to the side console (Figure 6). g024715 Figure 8 1. Floor-pan opening 3. Hoses 2. Wire harness g024710 Figure 6 2. 1. Harness 3. Routing the Wire Harness to the Horn 1. Route the wire harness forward and along the hoses to the horn.
4. Connect the wiring-harness leg with the 2 terminals to the 2 terminals on the horn (Figure 10). g024729 Figure 12 1. Wiring harness 2. Boom-frame channel g024714 Figure 10 1. Horn 3. 3. Terminal of the wiring-harness leg 4 2. Terminal of the horn 5. Install the cover removed in step 1, and secure it with the 2 bolts. Installing the Horn Switch Routing the Wiring Harness to the Taillight 1. Connect the wiring harness to the light.
3. Lift the control-panel cover and the choke control (Figure 14). g361817 Figure 16 g024737 Figure 14 1. Control-panel cover 4. 1. Hole (control-panel cover) 3. Jam nut 2. Knurled nut 4. Horn switch 2. Choke control Remove the forward, round plug from the control-panel cover (Figure 15). 2. Insert the horn switch into the hole in the control-panel cover, and secure the switch with the knurled nut. 3. Thread the switch button onto the horn switch (Figure 17). g025027 Figure 15 1.
5 Installing the Seat Lock Parts needed for this procedure: g361818 Figure 18 1. Blade terminal (horn switch) 2. Harness terminal (labeled HORN SWITCH) Assembling the Control Panel 1. 1 Lock-mount bracket 1 Latch 1 Grip 1 Hex-head screw (12 x 20 mm) 1 Locknut (12 mm) Procedure Align the control-panel cover to the side console (Figure 19). 1. Remove the hairpin from the clevis pin (Figure 20). g024744 g024767 Figure 19 1. Control-panel cover 2. 3. Figure 20 2.
g024768 Figure 21 1. Clevis pin 3. Outboard-seat gusset 2. Lock bracket g024775 Figure 24 4. Align the lock bracket and the clevis pin through the hole of the outboard-seat gusset (Figure 21). 1. Clevis pin 2. Spring 5. Align the holes in the latch with the holes in the seat gussets (Figure 22). 8. Fully insert the clevis pin through the holes in the seat latch and the inboard-seat gusset. 9.
6 Installing the Personal Protective Equipment Storage Bags Parts needed for this procedure: g361784 2 PPE storage bag 2 Hoop rod 2 Mount bracket 2 U-bolt 4 Flange locknut (3/8 inch) Figure 27 1. U-bolt 2. Rollbar tube 4. Repeat step 3 at the other side of the machine. 5. Insert the hooks of the hoop rod into the slots in the mount bracket (Figure 28). Procedure 1. 3. Mount bracket 4. Flange locknut (3/8 inch) Insert a hoop rod into the sleeve of the PPE storage bag as shown in Figure 26.
7 Applying the Decals to the Machine Parts needed for this procedure: 2 Boom lift-point decal 1 Tank-contents decal Applying the Boom Lift-Point Decals 1. Locate the middle of an outer boom, between the brackets, as shown in Figure 29. g024555 Figure 29 1. Boom lift-point decal 2. Clean the surface of the truss tube at the location that you identified in step 1, ensuring the surface is free of dirt, grease, or other foreign material. 3.