Installation Instructions

ManualsBrandsToro ManualsSprayersCE Kit, Multi Pro 1750 Turf Sprayer

FormNo.3383-692RevA

CEKit

MultiPro1750TurfSprayer

ModelNo.41202

InstallationInstructions

Safety

WARNING

CALIFORNIA

Proposition65Warning

Thisproductcontainsachemicalorchemicals

knowntotheStateofCaliforniatocausecancer,

birthdefects,orreproductiveharm.

SafetyandInstructionalDecals

Safetydecalsandinstructionsareeasily

visibletotheoperatorandarelocatednear

anyareaofpotentialdanger.Replaceany

decalthatisdamagedorlost.

104-8904

1.Grasptheboomhere.

119-9434

1.Tankcontents

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3383-692*A

Summary of content (8 pages)

PAGE 1
Form No. 3383-692 Rev A CE Kit Multi Pro 1750 Turf Sprayer Model No. 41202 Installation Instructions Safety WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 104-8904 1. Grasp the boom here.
PAGE 2
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 Description Use Qty. Boom decal Magnetic tank contents decal Rear light Bracket Nut (5/16 inch) Bolt (5/16-18 x 3/4 inch) Palnut Horn assembly Hex-head screw (5/16-18 x 3/4 inch) Flange nut (5/16-18) 2 1 1 1 2 2 2 1 1 1 Wiring harness 1 Route the wiring harness. Horn button 1 Install the horn button.
PAGE 3
2 2 1 3 Installing the Rear Light Parts needed for this procedure: 1 Rear light 1 Bracket 2 Nut (5/16 inch) 2 Bolt (5/16-18 x 3/4 inch) 2 Palnut g025026 Figure 3 1. Rear-light 1. Align the holes of the rear-light bracket with the 2 holes in the boom-frame channel. 3. Palnuts 2. Rear-light bracket 2. Secure the bracket to the frame with the 2 bolts (5/16 x 3/4 inch) and 2 locknuts (5/16 inch) as shown in Figure 2.
PAGE 4
Figure 4 1. Horn assembly 3. Flange nut (5/16-18) 2. Hex-head screw (5/16-18 x 3/4 inch) 4 Routing the Wiring Harness Parts needed for this procedure: 1 Wiring harness Use the following graphic for an outline of routing the wire harness to the machine (refer to Figure 5). g025033 Figure 5 Routing the Wiring Harness to the Side Console 1. Route the harness through the front of the seat shroud (Figure 6).
PAGE 5
Figure 6 Figure 9 1. Opening in the front of the seat shroud 1. Floor-pan opening 3. Hoses 2. Wire harness 2. Route the harness to the side console (Figure 7). 2. Route the wiring harness forward and along the hoses to the horn. 3. Route the wire harnesing through the grommet at the hole in the rear-angle platform to the horn (Figure 10). Figure 7 1. Harness Routing the Wiring to the Horn 1. Remove the 2 bolts that secure the hose cover to the machine, and remove the cover (Figure 8 and Figure 9).
PAGE 6
Figure 13 Figure 11 1. Horn 1. Wiring harness 3. Terminal of the wiring-harness leg 2. Terminal of the horn 2. Boom-frame channel 3. Connect the wiring harness to the light. 5. Install the cover removed in step 1, and secure it with the 2 bolts. 5 Routing the Wiring Harness to the Taillight Installing the Horn Button 1. Route the wiring harness along the right-frame channel adjacent to the tank (Figure 12). Parts needed for this procedure: 1 Horn button Procedure 1.
PAGE 7
Figure 15 1. Control-panel cover Figure 18 2. Choke control 1. Control-panel cover 4. Remove the forward, round plug from the control-panel cover (Figure 16). 2. Side console 8. Secure the control-panel cover to the side console with the 4 hex-head screws (1/4 x 1/2 inch) removed in step 2. 1 6 Installing the Seat Lock Parts needed for this procedure: g025027 Figure 16 1. Forward, round plug 5. Insert the new horn button into the control-panel cover (Figure 16). 6.
PAGE 8
2. Remove the clevis pin and spring from the latch (Figure 19). 7. Install the spring onto the clevis pin (Figure 23). 3. Partially insert the clevis pin through the lock bracket (Figure 20). Figure 23 Figure 20 1. Clevis pin 1. Clevis pin 3. Outboard-seat gusset 2. Spring 2. Lock bracket 8. Fully insert the clevis pin through the holes in the seat latch and the inboard-seat gusset. 4. Align the lock bracket and the clevis pin through the hole of the outboard-seat gusset (Figure 20). 9.