Operator's Manual

ManualsBrandsToro ManualsSprayersChemical Pre-Mix Kit, Multi Pro 1750 Turf Sprayer

FormNo.3379-560RevB

ChemicalPre-MixKit

MultiPro1750TurfSprayer

ModelNo.41210—SerialNo.314000001andUp

Operator'sManual

Thiskitisdesignedtoaidinthemixingofchemicalsin

preparationforturfsprayapplicationsonwell-maintained

lawnsinparks,golfcourses,sportselds,andoncommercial

grounds.Itisadedicatedattachmentforaturfspray

applicationvehicleandisintendedtobeusedbyprofessional,

hiredoperatorsincommercialapplications.

ThisproductcomplieswithallrelevantEuropeandirectives;

fordetails,pleaseseetheseparateproductspecicDeclaration

ofConformity(DOC)sheet.

Readthismanualcarefullytolearnhowtooperateand

maintainyourproductproperly.Theinformationinthis

manualcanhelpyouandothersavoidinjuryandproduct

damage.AlthoughTorodesignsandproducessafeproducts,

youareresponsibleforoperatingtheproductproperlyand

safely.

YoumaycontactTorodirectlyatwww .Toro.comforproduct

andaccessoryinformation,helpndingadealer,ortoregister

yourproduct.

WARNING

CALIFORNIA

Proposition65Warning

Thisproductcontainsachemicalorchemicals

knowntotheStateofCaliforniatocausecancer,

birthdefects,orreproductiveharm.

Useofthisproductmaycauseexposureto

chemicalsknowntotheStateofCalifornia

tocausecancer,birthdefects,orother

reproductiveharm.

Wheneveryouneedservice,genuineToroparts,oradditional

information,contactanAuthorizedServiceDealerorToro

CustomerServiceandhavethemodelandserialnumbersof

yourproductready.Figure1illustratesthelocationofthe

modelandserialnumbersontheproduct.

G013916

Figure1

1.Modelandserialnumberplate

ModelNo.

SerialNo.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3379-560*B

Summary of content (16 pages)

PAGE 1
Form No. 3379-560 Rev B Chemical Pre-Mix Kit Multi Pro 1750 Turf Sprayer Model No. 41210—Serial No. 314000001 and Up Operator's Manual This kit is designed to aid in the mixing of chemicals in preparation for turf spray applications on well-maintained lawns in parks, golf courses, sports fields, and on commercial grounds. It is a dedicated attachment for a turf spray application vehicle and is intended to be used by professional, hired operators in commercial applications.
PAGE 2
Safety WARNING Chemical substances used in the spray system may be hazardous and toxic to you, bystanders, animals, plants, soils, or other property. • Carefully read and follow the chemical warning labels and Material Safety Data Sheets (MSDS) for all chemicals used, and protect yourself according to the chemical manufacturer's recommendations.
PAGE 3
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Use 1 Support frame assembly Locknut (3/8 inch) Back plate assembly Cradle arm, right Cradle arm, left Bushing Pivot pin Jam nut (3/8 inch) Handle Bolt (3/8 x 1-1/4 inches) Set screw Hair pin Flat washer Thick square spacer Thin square spacer 1 1 1 1 1 2 2 2 2 2 2 2 2 2 2 Assemble the frame. 2 Spring 2 Install the latching components.
PAGE 4
Procedure 6 7 Description Use Qty. 90° fitting Hose clamp 1 2 Install the 90° fitting. Suction lance and hose (optional) 1 Finish the installation. Note: Determine the left and right sides of the machine from the normal operating position. Note: Use the appropriate number and size of square spacers to ensure that the frame is flush with the tank.
PAGE 5
2 1 3 4 G013929 Figure 6 1. Left cradle arm 2. Pivot housing 3. Set screw 4. Holes in cradle arm Figure 5 1. Back plate assembly 7. Handle 2. Hair pin 8. Bolt (3/8 x 1-1/4 inches) 3. Flat washer 9. Right cradle arm 4. Bushing 10. Main support frame assembly 5. Pivot pin 11. Cradle arm axle 6. Jam nut (3/8 inch) 12. Pivot housing 2 Installing the Latching Components Parts needed for this procedure: 9. Loosely attach the left arm to the exposed axle on the other side of the frame. 2 10.
PAGE 6
3. Make sure that the spring end is seated properly in the groove in the post (Figure 7). 3. Tighten the fasteners in the tongue to secure its position, then release pressure on the back plate. 4. Repeat steps 1 through 3 for the other side. Note: Check to see if there is any play in the cradle. It should be held snug to the frame assembly. You can repeat this procedure once the eductor is installed to adjust the locked position. 5. Tighten the 2 set screws in the left arm.
PAGE 7
3 Installing the Eductor Parts needed for this procedure: 1 Eductor 1 Handle 2 Flange-head bolt 1 Spring clamp 2 Bolt (#10-24 x 1/2 inch) 2 Locknut (#10-24) 4 Bolt (3/8 x 1 inch) 4 Locknut (3/8 inch) 2 Flange-head nut 2 Hex-head bolt 1 Latch post 1 Latch handle 4. Eductor 1 T-valve 5. Flange-head nut 1 Gasket 1 Worm-screw clamp Figure 10 1. Latch post 6. Spring clamp 2. Hex-head bolt 7. Bolt (#10-24 x 1/2 inch) 3. Handle 8. Flange-head bolt 9. Locknut (#10-24) 10.
PAGE 8
Note: Torque the fasteners to 36-45 N-m (27-33 ft-lb). 10. Tighten the 2 set screws on the left hand pivot arm. 11. Check the overall position of the eductor assembly on the tank strap. Note: The eductor should be upright, in the transport position. Loosen the lower locknut on the frame assembly securing it to the tank. Do not remove the locknut. Adjust the position as necessary and tighten the locknut. Make sure that the strap is secure to the tank. 12.
PAGE 9
Installing the Hose Note: Locate the drill mark in the center of the molded circle. 1. Install the hose end with the 90° fitting to the previously installed bulkhead using a retaining fork (Figure 16). Figure 14 Figure 16 1. Eductor hose assembly 2. Use a 9 cm (3-5/8 inch) hole saw to drill a hole at the drill mark (Figure 14). 2. Retaining fork 2. Attach the other end of the hose to the forward-facing opening of the eductor using a gasket and worm-screw clamp (Figure 17).
PAGE 10
1 2 G014016 3 Figure 18 1. Eductor hose 2. Tank 3. Slack in the hose Figure 20 1. Retaining fork 4. Secure the end of the supply hose without a bulkhead to the rear opening on the eductor valve using a gasket and worm-screw clamp (Figure 19). 3. Pressure hose 2. Bolts 2. Remove the 2 bolts securing the small bracket to the frame (Figure 20). 3. Using the previously removed bolts, install the valve bracket over the small bracket (Figure 21). Figure 19 1. Eductor 2. O-ring 3. Hose 4.
PAGE 11
6 Installing the 90° Fitting Parts needed for this procedure: 1 90° fitting 2 Hose clamp Procedure 1. Measure and cut 7.5 cm (3 inches) from the end of the agitation hose (Figure 22). Figure 22 1. Agitation hose 3. 7.5 cm (3 inch) section of hose 2. 90° fitting 2. Attach the 90° fitting to the 7.5 cm (3 inch) section of hose with a hose clamp. 3. Trim the excess from the agitation hose and connect it to the 90° fitting with a hose clamp (Figure 22).
PAGE 12
Handles and Transport Strap Operation Use the upper and lower handles to raise and lower the eductor and to lock it into the transport position. CAUTION Chemicals are hazardous and can cause personal injury. Main Valve Use the main valve to introduce chemicals from the eductor into the hose leading to the main tank. • Read the directions on the chemical labels before handling the chemicals and follow all manufacturer recommendations and precautions.
PAGE 13
Raising the Eductor Starting the Eductor 1. Lift the lower handle to raise the eductor while slightly tipping it toward the tank. Note: Close the eductor hopper valve and hopper rinse ball valve(s) before starting the eductor. 2. Guide the tongue under the crossbar with the welded tab in the upper portion of the frame assembly. 1. Lower the eductor. 2. Open the lid to check for foreign objects which may hinder performance or contaminate the system. 3.
PAGE 14
2 1 G016600 Figure 25 1. Suction lance 2. Eductor 2. Use the free end of the lance to pierce the bag or container to vacuum powdered or liquid chemical. 3. Place the lance end into a clean container of water to rinse the lance assembly. 4. Remove the lance body from eductor and drain any remaining fluid into the hopper. 5. Close the hopper valve (red handle). Shutting down the Eductor 1. Close all the valves. Note: Close the hopper valve first. 2. Remove all chemical residue. 3.
PAGE 15
Troubleshooting Problem The eduction rate is low. Possible Cause 1. There is a lack of flow and pressure to the eductor system. 1. Increase the pump speed. Turn the agitation throttling toward the closed position. 2. The outlet/Inlet hose is obstructed. 2. Disassemble and remove any obstructions. 3. Use only sweeping turns with flexible hoses. 3. Fittings with elbows or other flow-restrictions are in the eductor outlet. There is no rinsing or flushing action. There are leaks at the fittings.
PAGE 16
The Toro Total Coverage Guarantee A Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).