FORM NQO. 92-3720 To assure maximum safety, optimum performance, and to gain knowledge of the product, it.is essential that you or any other operator of this Vehicle read and understand the contents of this manual before the engine is ever started. Pay particular attention to the SAFETY INSTRUCTIONS highlighted by this symbol R MODEL NO. 41080-30001 & UP MODEL NO. 41021-30001 & UP MODEL NG. 41220-30001 & UP MODEL NO. 4122130003 8 UP MODEL NO.
SAFETY INSTRUCTIONS B. Follow manufacturer’s instructions on chemical container labels. Apply and handle chemicals as recommended. C. Handle and apply chemicals with care. Wear goggles and other necessary protective equipment. Handle chemicals in well ventilated areas. Never smoke while handling chemicals. chemical container and unused chemicals. WHILE OPERATING: 5. Drive the vehicle safely. A. Always SLOW the vehicle when approaching and while making a turn. B.
A SAFETY AND INSTRUCTION DECALS A CAUTION ‘= CHEMICALS CAN BE AEROSOLS: DANDLE AND APPLY WITH CARE, LAMS, PLANTS, S0 A PROFLIGATE, 15 OR IMPORTANT TO ELIMINATE ENVIRONMENTAL DAMAGE AND PERSONAL INJURY #SELECT THE BIGHT CHEMICAL FOR THE 408, »FOLLOW INSTRUCTIONS ISSUED BY CHEMICAL MANUFACTURER, NO STEP! {Part No, 36-2400) Top of Radiator Cover SPRAYER (Part No. 87-0520) On top of Ark Lid {Part No. 92-2663) Under dash below Fuse Brock TO VOILA ELECTRIC SHOCK AHD PERSONAL INJURY T BYSTANDERS .
CONTROLS and OPERATION NOTE: are referenced while seated operator’s position. ELECTRIC CLUTCH/PUMP SWITCH (FIG 1): This switch located on the sower dash panel, when moved to the 'ON’ position, engages the pump drive belt. Move the switch to the *OF F* position to disengage the pump drive belt. PRESSURE ADJUST SWITCH (FIG 1): Hold to INCREASE or DECREASE spraying pressure to desired level. Located on Control Connote.
OPERATION SYSTEM SET-UP: 1. Fill the Tank with clean, clear water. IMPORTANT: Do not operate the pump dry. Damage will result to the pump seals if the pump is operated dry. Be certain the suction line valve is "OPEN” before engaging the pump. 2. Take the vehicle out of gear and set the parking brake.. Move Electric Clutch Switch to "OFF" position {refer to Workman Operator's Manual). Start the engine and set the throttle at 3/4 to full RPM to represent your desired spraying speed.
OPERATION FILLING THE SOLUTION TANK: (Cont'd) 1. Most chemicals are heavier than the water to which they are introduced. 2. Fill the spray tank 1/2 full with clear water from a clean source. 3. Start vehicle and tum on pump with booms off and by-pass fully open. 4. Begin adding the chemicals very gradually, allowing the pump and agitation to fully mix the chemicals. 5. Fill the remainder of the tank with clear water. USING THE SPRAYER: IMPORTANT: Do not operate the pump dry.
MAINTENANCE Wash spray tips thoroughly with water. Blow out orifice, clean and dry. If orifice remains clogged, clean it with a soft bristled brush...never use a metal object. SUCTION STRAINER: Turn off Suction Line Valve if Tank is full of spray solution, Remove the cap and clean the strainer screen daily when spraying settable powders after every 50 hours whiner using liquid chemical. IMPORTANT: Do not operate the pump dry. Damage will result to the pump seals if the pump is operated dry.
MAINTENANCE PROCEDURES FOR REPLACING THE SHAFT BEARINGS AND SEAL IN THE TOR CENTRIFUGAL SPRAYER PUMP A WARNING! Before servicing or making any adjustments fo the Sprayer, stop the transport vehicle and set the parking brake. Shut off the vehicle's engine and remove key from ignition. Disengage all power and wait until all moving parts have stopped. To service the bearings (12), take the volute (1) and the impeller (7) off the shaft (10).
MAINTENANCE TROUBLESHOOTING THE 42871 SOLENOID VALVE CONDITION POSSIBLE CAUSES HOW TO CHECK 1. Valve won't open A. No electrical power to valve Manually activate valve. If stem moves freely, check and clean electrical connections. Inspect electrical system, B. Stroke too long Energize coll. Check length of stroke should be approximately /8", If not, reset stroke. C. Stem movement restricted Manually activate stem by pushing on lower diaphragm piston, If more than § Ibs.
STORAGE Flush the entire spraying system with clear water. Drain the entire spraying system thoroughly, and run some antifreeze through the entire spraying system. This will acts a Lubricant and prevent freeze-ups -in the system components, FREEZING TEMPERATURES MAY DAMAGE THE PRESSURE REGULATING VALVE AND THE ELECTRIC SOLENOIDS IF WATER 1S NOT DRAINED COMPLETELY! SERVICING AFTER STORAGE: Flush the entire spraying system with clean water and detergent.
FINDING THE CORRECT NOZZLE SIZE GPM GPA MPH xW* Example: B1GPM = 80 GPA x 3 MPH x 20* {Par Nozzle)} 5840 5940 *W = Nozzle spacing in inches. Capacity APPLICATION RATES FOR NOZZLES TOR Nozzle Pressure [1-Nozzle 20" SPACING Partner Number | (PSI) | (GPM) [ NONSPECIALIZING GALLONS PER 7000 5161 Catchwords mp | mPH | MPH | MPH MPH | MPH | MPH | MPH 43082 | RA-B 175 120° 1145 Blue 129 47088 | AA—6 120" 118 138 | 108 Goren 182 1 145 | 92 76 32628 | RA-B 129 120° 156 | 117 1,84 1.
The Toto Promise A One Year Limited Warranty The Toto Company promises to repair your Manual Spray System for the Workman vehicle (comprising of models 41021, 41080, 41220, 41221, 41222} if defective in materials or workmanship. The following time periods from the date of purchase apply (special warranty terms, on certain components, may be offered through The Tore Compare by the component manufacturers): Commercial Products wees 1 Year The cost of parts, labor and transportation are included.