. Install the TOR APU Electric Clutch Kit as per the instructions provided with that kit, 2, Remove the four “bolts “and discard “the aluminum. caver that is located on iop of the trans axle. Apply a thin bead of RTV sealer around the outer bottom edge (side opposite tapped hole) of the the new sensor cover, Position the. new sensor cover on the trans axle as shown in FIG. 1 and secure with bolts earlier removed, Apply a few.
the rear mounting Holt on the hydraulic naive. If equipped with the auxiliary hydraulic package, it is necessary to removal the last two mounting obits of this naive. This will allow for the usage of the bolt holes to properly install the pump mounting plate. Reuse the fasteners earlier removed, 9. Almach the pump mount bracket assembly to the left side of the vehicle frame using the (8) 5{16" x 1* hex hd. cap screws, lock washers, and hex nuts {FIG. 4).
hose next to the street elbow in the suction port of the pump. On models equipped with the liquid cooled gas engine, install the hose protector and nylon tie on the upper radiator hose above the pump belt. This is to prevent the hose from wearing through prematurely. 14. Unplug the wire shames connectors from both headlights. 15. Remove (15) screws and washers securing front hood to vehicle frame and remove hood. 16.
2Z7. Remove the (2) screws that hold the console and console mounting bracket to the vehicle. 28. Reinstall the hood and remount the console and console mounting bracket using the 15 screws and washers earlier removed and install the "R" clamp on the console control cable and secure {FIG. 7). 29. Reconnect the wire shames connectors to both headlights. 30. l Loosen and remove the (2) 3/8" nuts and attaching bolts that hold the left rear fender to the vehicle frame. Install a 10 GA.
39. Locate and remove the (2) 1/2° bolts on each side of the vehicle frame as shown and install the attachment mounting bracket using the bolts earlier removed. Re-tighten the nuts and bolts securely (FiG. 11). 40, Release the strut support rod and lower the tank and saddle assembly. 41, Attach the two boom mount upright angles onto the rear of the tank saddle extensions using hex hd. cap screws and lockouts (FIG. 12). FiG. 12 1. Upright Angles 5. Spacer Tubes 2. Upper Cross Support 8. Center Boom Angle 3.
FIG. 14 1. Extension Boom Pipe 3. Boom Support Says. 2. Pivot Assembly 52, Secure the two plates of boom support assembly to the extension boom pipe, using (2) 1/4" U-obits, (4) flat washers, and (4) lockouts {FIG. 18}, 53, Assemble the boom support assembly to the other extension boom pipe. 54. At the adjustable clevis assemblies (See FIG.
63. Place a hose clamp on the right and left boom feeder hoses and attach them to the double barb nozzles on the right and left extension boom pipes. 64. Assemble the pressure gauge and the 3/8" hose barb to the gauge bracket. Remove the protective cap and mount the bracket to the carriage obit in the rear tan band, using a 5/16° hex nut and lock washer (FiG. 16). 65, Connect the pressure gauge to the solenoid assembly with the 3/8" x 36" hose. Secure the hose with hose clamps (FIG. 16).
2. Release the strut rod and lower the tank skid assembly. < 83. Secure the tank skid to the vehicle frame by installing the (2) 1/2" bolts, (4) washers, and {2) lockouts through the attachment mounting brackets (FIG. 11). Tighten fasteners securely. 84, Attach the suction hose o the suction strainer using the quick couplets, 85, Recheck and tighten all fasteners and hose clamps securely. 86. Fill the tank with clean water and check for any leaks. 87.
B [ LTS e Located st Fuse Fart No. 75-5180: Located on Radiator Cover Block {1} top, front & rear {2). Part No. 80-8040: Located on Radiator Cover top, Font & rear £2). A CAUTION BTR Part Ne, 363400: Located on Radiator Cover, top sides (2. AND APPLY WITH CARE. PAPER SELECTION OF USE iRh it A (HAILS FLAN'S SULFUROUS Part No. 92-2668: Located on Tank Sid left side @ strut ) Part No, 87-0520: : Located on Tank Lid {1 LOW PROFILE =@ @) GALLON Part No.
! 00 REF PART NO. DESCRIPTION Nary 1 42983 Hold-In Brace Says. 22-12-AJ0 Hex Nut, 5/16 24-10-DB Hat washer, 5/16 SA .12 4 S-0010 U Bolt, 14NC 42198 Rubber Hold-Down Strap .2 6 42259 Boom Hold-n Says LH shown) .1 7 42318 Boom Hood-in Says RH. (oppose) 2-11-AJFD Lock Nut 14NC .. .8 9 26-25-GAD Carriage Bolt, 5/16 92-3668 Ta pk Band Front 42452 Protective Cap . 2 12 828667 Tank Band Rear. 1 14 42822 Tank Lid (fw Tank Says) .
BOOM FRAME REF PART NO. DESCRIPTION Qry 1 92.3671 Boom Mounting Angle LH. 92-8672 Cross Angle Upper 22-15-AJFD Lock Nut, 1/2NC 823670 Boom Mourning Angle RH. .1 8 20-86-GAD HHS, 1/2 NC x 3-1/4 8 6 42925 Cross Support Angle . Lt 7 42258 Spacer Tube, Lg. .2 8 22-12-AGED Hex Nut, 516 42284 Center Boom Angle .2 10 2410-AD Flat washer, 516 .4 11 20-47-GAD HHS, 24-11-AD Flat washer, 3/8 . .2 13 40493 Conner Boom Pipe . i 1 14 40494 CIA SAYS. .lien e .2 15 22-13-AJFD Lock Nut, 3/8NC . .
Sl SSE| REF PART NO. DESCRIPTION ary 1 2851 90° Elbow, NPT | -1 2 92-3729 Nipple, {-1/4 MPT 5703 90° St Elbow, NPT | -1 4 H7502 Centrifugal Pump 5708 45° St Elbow, 1" NPT . .2 6 93731 Nipple, 1" MPT 41316 Quick Adapter, 1* FPT 2 41318 Oust Cap 2 8 HHS, 38 NC x .. 3 8 67-1440 Tension Spring 22-13-AJFD Lock Nut, 378 Ar-7 CamageEolt.SlsNCxa‘ . 1 12 52-2880 Eyeliner Bushing . 2 13 92-8740 tidier Bracket . 1 14 92-3701 Tidier Spacer (lns!de) 1 18 680030 Wl Populism {snide) .
PRO CO RAY S 00; REF PART NO. DESCRIPTION arY 1 92.3688 Console Control Cable (1BR) L1 2 24-10-DB Flat washer, 5116 . 18 3 22-12-AGED Hex Nut, 5/16 NC 14 4 92-3675 Manifold Mtg. Plate 20-26-GAD HHS, 18 NCx 253-10-GD Lock Washer, §/16 .. 7 92-3677 Connector Hose, 21146 Hose Clamp 92-3638 Adapter, "HB X 1 10 41327 Hose Clamp 4 ki 41820 Adulator Hose, 41482 Flow Meter .1 18 41308 Hose Barb, 1" MPT x HB 1 14 413058 Tee, 1" NPT . 8 15 41315 Hex Plug, 1" MPT . -1 16 41304 Close Nipple, 1"NPT .. .
REF PART NO. DESCRIPTION ary 1 920045 Hose Clamp, 3/4 Hose 2 40806 imper Hose, 41340 Boom Hose {Right & Lefty 42274 Boom Hose {Center) 42282 Extension Boom F Pipe Says 40400 Canter Boom Pipe 1 7 41001 Nozzle Body & Check Naive Double & 8 41002 Snazzy Body & Check Naive (Triple Barb) . 1 8 41000 Nozzle Body & Check Valve {Single Serb) 4 41003 Diaphragm (fw 41000, 41001 & 41002) AR 10 40899 Clamp SAYS . .. ., 1 11 40997 Adapter Cap & Seat Gasket Says kil 40998 Beat Gasket (ffw 40887} ..
CONTROL CONSOLE (3000) REF PART NO. DESCRIPTION Qty Y 1 41472 Control Cons Ole .. .\ v. mitt 41344 Console Protective Cover 1 2 42722 POWER Switch B 3 42723 Rate 1/Rate 2 Manual Switch . 1 4 42724 MAN AJD Switch .1 5 42558 BOOM Switch . .8 6§ 42725 MASTER Switch Lt 42715 Fuse Holder 1 7 20-5-GAD HHS, 1/4NCx 1 .2 8 41473 Mounting Knob 41474 Mounting Bracket 22-9-GD Lock Washer, /4 . Americanize 2 " 2211-AGED Hex Nut, 41230 Cable Clamp .2 13 92.2661 Wiring Ha mess Speed Sensor . .