Operator's Manual

ManualsBrandsToro ManualsSprayersFoam Marker Kit, Multi Pro 5800, 1750 and WM Turf Sprayer

FormNo.3378-331RevB

FoamMarkerKit

MultiPro5800,1750,andWMTurfSprayer

ModelNo.41232—SerialNo.314000001andUp

Operator'sManual

WARNING

CALIFORNIA

Proposition65Warning

Thisproductcontainsachemicalorchemicals

knowntotheStateofCaliforniatocausecancer,

birthdefects,orreproductiveharm.

Safety

Note:Determinetheleftandrightsidesofthemachine

fromthenormaloperatingposition.

SafetyandInstructional

Decals

Safetydecalsandinstructionsareeasily

visibletotheoperatorandarelocatednear

anyareaofpotentialdanger.Replaceany

decalthatisdamagedorlost.

112-7890

1.Foamoutput3.Decrease

2.Increase

Setup

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine

Regulatingvalve,capmount1

Regulatingvalve,dashboardmount1

Decal,112-78901

Installthefoamcontrolvalve.

Hoseclamps(blue)

Hoseclamps(white)

Brackets4

Spacers

Setscrews

Mountingrod2

Foam-nozzleassemblies2

Installthefoamnozzles.

Foammarkernishingkit(sold

separately)

Installthefoammarkerkitandthe

bracket.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3378-331*B

Summary of content (12 pages)

PAGE 1
Form No. 3378-331 Rev B Foam Marker Kit Multi Pro 5800, 1750, and WM Turf Sprayer Model No. 41232—Serial No. 314000001 and Up Operator's Manual Safety and Instructional Decals WARNING CALIFORNIA Proposition 65 Warning Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost.
PAGE 2
Procedure 5 6 Description Use Qty. Foam hose Plastic ties 1 8 Route the foam hoses. No parts required – Connect the hoses. Separate instructions for the installation of the foam marker kit are denoted in each step of the Setup where specific procedures deviate from 1 machine to another. Please look for the heading describing instructions specific to the machine you are working with before proceeding with each step of the Setup.
PAGE 3
Installing the Foam Control Valve on Multi-Pro 5000 Series Turf Sprayers 1. Locate the foam hose previously routed forward to the cab. 2. Install a plastic tube clamp to the exposed foam tubes. Note: Use a blue clamp for the blue (fluid) tube and a white clamp for the clear (air) tube. 3. Depending on the model, drill or knock out a hole in the dashboard. For a Multi-Pro 5700 model: A.
PAGE 4
7. Wrap PTFE thread tape around the threads of the knob assembly. 3 8. Install the threaded end of the knob assembly through the dashboard knock out hole. Installing the Foam Nozzles 9. On the underside of the dashboard, secure the regulating valve body to the knob by tightening the nut on the knob. Parts needed for this procedure: 10. Install the decal as shown in Figure 5.
PAGE 5
Figure 7 1. Upper-boom support pole 3. Spacer (note orientation) 5. Clamp screw 7. Set screw 2. Lower half of the bracket clamp 4. Lower half of the bracket clamp 6. Spacer nut 8. Mounting rod 5. Install the second bracket assembly 7 to 10 cm (3 to 4 inches) inboard from the first bracket. 6. Install a set screw in the top hole of each spacer. 7. Install the mounting rod, with the splined end outward, into the holes in the spacers. Note: Use the set screws to secure the rod in the desired position.
PAGE 6
4 Installing the Foam Marker Kit and the Bracket Parts needed for this procedure: 1 Foam marker finishing kit (sold separately) See the installation instructions that came with the foam marker finishing kit. 5 Routing the Foam Hoses Parts needed for this procedure: 1 Foam hose 8 Plastic ties Cutting Lengths for Foam Hose Figure 8 1. Splined-end mandrel 3. Blue tube and clamp 2. Foam nozzle 4. Clear tube and white clamp 1750 Series 5000 Series WM (Workman) 200 Right boom foam hose 5.
PAGE 7
Important: The foam hoses will be pinched when the booms are in the “X” transport position if they are installed on the wrong side. Note: Use plastic ties to secure the hose to the brace at the positions shown in Figure 11. Figure 11 1. Plastic ties D. Important: The foam hoses will be pinched when the booms are in the “X” transport position if they are installed on the wrong side. Figure 9 Multi-Pro 5000 Series shown 1. Foam hose on the right boom B.
PAGE 8
Route a separate foam hose forward toward the cab to prepare for installation of the control valve. 6 1. Locate the 16-foot foam hose for the dashboard-mounted control valve. Connecting the Hoses 2. Route the hose from the foam marker bracket forward, below the chemical tank and behind the fuel tank, along with existing wiring to the area under the seat box (Figure 13). No Parts Required Connecting the Hoses on Multi-Pro 1750 Series Turf Sprayers and WM (Workman) Turf Spray Systems 1.
PAGE 9
Figure 16 Connecting the Hoses on Multi-Pro 5000 Series Turf Sprayers 1. Connect the electrical plug from the foam marker tank assembly to the open plug in the wiring harness at the bracket. 2. Locate the open tube ends from the long hose routed to the dashboard previously installed, and install the blue tube to the an open barb on the black, tank cap. Note: Install the clear tube to the blue or water barb on the compressor shown in Figure 17. Use a blue tube clamp to secure both tubes.
PAGE 10
5. Locate the foam hose routed to the left boom, and install the blue and white tube to the locations as shown in Figure 17. 3. Locate the short, loop-back hose previously cut, and install the clear tube to the remaining barb on the tank cap shown in Figure 17. 6. Locate the foam hose routed to the right boom, and install the blue and white tube to the locations as shown in Figure 17. Note: Route the open end to the air or white barb on the compressor. Use white tube clamps to secure the tube. 7.
PAGE 11
Operation Using the Controls Right boom switch—activates the compressor, generating a flow of water and air to the right boom section. Left boom switch—activates the compressor, generating a flow of water and air to the left boom section. Note: You can drop the foam simultaneously from both boom sections. Indicator markings—located on the side of the tank, they indicate the solution level in the tank. Figure 19 1. 1/4 turn open Foam regulator adjustment valve—controls the consistency of the foam solution.
PAGE 12
Storage 1. Move the vehicle onto a level surface, set the parking brake, stop the pump, stop the engine, and remove the ignition key. 2. Relieve pressure within tank by opening the tank fill cap, install the tank fill cap, and hand tighten it. 3. Disconnect the air and liquid tubing from the tank. Note: Replace air and liquid tubing together with the supplied tubing coupler. 4. Disassemble the foam nozzles and replace the foam sponges. 5.