Operator's Manual

ManualsBrandsToro ManualsSprayersTank Cleanse Rinse Kit, Multi Pro WM Turf Sprayer

FormNo.3379-584RevB

TankCleanseRinseKit

MultiProWMTurfSprayer

ModelNo.41241—SerialNo.314000001andUp

Operator'sManual

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

WARNING

CALIFORNIA

Proposition65Warning

Thisproductcontainsachemicalorchemicals

knowntotheStateofCaliforniatocausecancer,

birthdefects,orreproductiveharm.

Useofthisproductmaycauseexposureto

chemicalsknowntotheStateofCalifornia

tocausecancer,birthdefects,orother

reproductiveharm.

Thiskitisdesignedtoremoveresidualchemicalsfroma

sprayertankandaffectedhoses.Itisadedicatedattachment

foraturfsprayapplicationvehicleandisintendedtobeused

byprofessional,hiredoperatorsincommercialapplications.

ThisproductcomplieswithallrelevantEuropeandirectives;

fordetails,pleaseseetheseparateproductspecicDeclaration

ofConformity(DOC)sheet.

Readthismanualcarefullytolearnhowtooperateand

maintainyourproductproperly.Theinformationinthis

manualcanhelpyouandothersavoidinjuryandproduct

damage.AlthoughTorodesignsandproducessafeproducts,

youareresponsibleforoperatingtheproductproperlyand

safely.

YoumaycontactTorodirectlyatwww .Toro.comforproduct

andaccessoryinformation,helpndingadealer,ortoregister

yourproduct.

Wheneveryouneedservice,genuineToroparts,oradditional

information,contactanAuthorizedServiceDealerorToro

CustomerServiceandhavethemodelandserialnumbersof

yourproductready.Figure1illustratesthelocationofthe

modelandserialnumbersontheproduct.

Figure1

1.Cover

3.Modelandserialnumber

plate

2.Pump

ModelNo.

SerialNo.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3379-584*B

Summary of content (12 pages)

PAGE 1
Form No. 3379-584 Rev B Tank Cleanse Rinse Kit Multi Pro WM Turf Sprayer Model No. 41241—Serial No. 314000001 and Up Operator's Manual Note: Determine the left and right sides of the machine from the normal operating position. WARNING CALIFORNIA Proposition 65 Warning Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your product ready.
PAGE 2
Safety • Obtain proper training before using or handling Also read the safety and operation instructions in the vehicle Operator’s Manual. • Use the correct chemical for the job. chemicals. • Follow the chemical manufacturer's instructions for the safe application of the chemical. Chemical Safety • Handle chemicals in a well-ventilated area. • Wear goggles and other protective equipment as WARNING instructed by the chemical manufacturer.
PAGE 3
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 Description Use Qty.
PAGE 4
1 2 Preparing the Machine Installing the Rinse Tank No Parts Required Parts needed for this procedure: Procedure 1. Move the sprayer onto a level surface, set the parking brake, stop the pump, stop the engine, and remove the ignition key. 2. Drain the contents of the tank to remove any solution in lines. Refer to the Operator’s Manual for more information.
PAGE 5
Install the Rinse Tank 3 1. Install the rinse tank as shown in Figure 3. Note: If there is not enough space for the rinse tank, loosen both of the main tank straps, and slide the main tank rearward. Installing the Rinse Nozzles Parts needed for this procedure: 2 Rinse nozzle 2 Bulkhead fitting 2 Shoulder bolt 2 Bushing 2 Rinse vane 2 90° barbed fitting 2 Plastic flange nut Drilling the Main Tank 1. Remove the tank lid and the strainer basket from the tank (Figure 4). Figure 3 1.
PAGE 6
Installing the Rinse Nozzles 1 1. Assemble the 2 rinse nozzles as shown in Figure 5. 2 1 2 G022283 Figure 7 3 1. 90° barbed fitting 2. Nozzle assembly 4 5. Direct the hose barbs toward the middle of the right side of the machine. 5 6. Install the tank lid and the strainer basket to the tank that you removed previously. G022281 Figure 5 1. Bulkhead fitting 4. Rinse vane 2. Rinse nozzle 3. Bushing 5. Shoulder bolt 4 Installing the Pump 2.
PAGE 7
5 Installing the Hoses and Filter 1 2 Parts needed for this procedure: 3 4 1 Filter 1 T-fitting 1 15 cm (6 inch) hose 1 101.5 cm (40 inch) hose 1 42 cm (16.5 inch) hose 2 61 cm (24 inch) hose 9 Hose clamp 1 Hose grommet 1 Rinse-pump cover 2 Hair pin G022291 Figure 8 1. Tank strap 3. Mounting bracket 2. Carriage bolt 4. Flange nut 2. Secure the pump to the frame using the 4 bolts, small washers, and nuts (Figure 9).
PAGE 8
Install the Rinse Tank Hose 2. Attach the loose ends of the hoses to the T-fitting with 2 hose clamps (Figure 10). 1. Install the hose grommet into the hole at the right side of the sprayer frame near the rinse tank (Figure 12). Install the Supply Hose and Rinse Filter 1. Attach one end of the 42 cm (16.5 inch) hose to the T-fitting with a hose clamp (Figure 11). 1 2 3 4 5 1 2 G022297 3 4 Figure 12 5 6 7 8 G022295 Figure 11 1. T-fitting 5. Rinse filter 2. Hose clamp 6.
PAGE 9
6 Installing the Dash Switch Parts needed for this procedure: 1 Dash switch Install the Dash Switch 1. Locate the plug for the rinse tank switch on the sprayer console, and remove the plug (Figure 14). A 1 B 2 3 G024048 Figure 14 1. Plug 3. Connector for rinse tank pump 2. Dash switch 2. Remove the 4 bolts securing the panel to the console, and locate the box connector labeled Rinse Tank on the main harness. 3. Install the switch to the box connector through the console (Figure 14).
PAGE 10
Operation Pressing the switch down engages a momentary switch. Power is supplied to the pump while the switch is held down. Release the pressure, and the switch moves to the Neutral position and power is not supplied to the pump. While the switch is held in the down position, the pump runs. Tank Cleanse Rinse Kit Operation The use of the Tank Cleanse Rinse Kit will result in a rinsate; a diluted solution of residual chemicals. In many cases it is appropriate to apply the rinsate onto the treated areas.
PAGE 11
Maintenance Storage Inspect the Rinse Pump Filter Drain the pump inlet line, outlet line, and filter line prior to storage for 30 days or more. Service Interval: After the first 5 hours Every 50 hours Check the filter for any signs of damage. Replace the filter if it is damaged. Inspect the Rinse System for Leaks and Damage Service Interval: Before each use or daily—Inspect the hoses for leaks. After the first 5 hours—Inspect the hoses for damage.
PAGE 12
The Toro Total Coverage Guarantee A Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).