Operator's Manual

ManualsBrandsToro ManualsSprayersTank Cleanse Rinse Kit, Multi Pro WM Turf Sprayer

FormNo.3391-742RevA

TankCleanRinseKit

MultiPro

WMTurfSprayer

ModelNo.41241—SerialNo.315000001andUp

Operator'sManual

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

UseofthisproductmaycauseexposuretochemicalsknowntotheStateofCalifornia

tocausecancer,birthdefects,orotherreproductiveharm.

Thiskitisdesignedtoremoveresidualchemicalsfroma

sprayertankandaffectedhoses.Itisadedicatedattachment

foraturfsprayapplicationvehicleandisintendedtobeused

byprofessional,hiredoperatorsincommercialapplications.

ThisproductcomplieswithallrelevantEuropeandirectives;

fordetails,pleaseseetheseparateproductspecicDeclaration

ofIncorporation(DOI)sheet.

Readthismanualcarefullytolearnhowtooperateand

maintainyourproductproperly.Theinformationinthis

manualcanhelpyouandothersavoidinjuryandproduct

damage.AlthoughTorodesignsandproducessafeproducts,

youareresponsibleforoperatingtheproductproperlyand

safely.

YoumaycontactTorodirectlyatwww .Toro.comforproduct

andaccessoryinformation,helpndingadealer,ortoregister

yourproduct.

Wheneveryouneedservice,genuineToroparts,oradditional

information,contactanAuthorizedServiceDealerorToro

CustomerServiceandhavethemodelandserialnumbersof

yourproductready.Figure1illustratesthelocationofthe

modelandserialnumbersontheproduct.

Figure1

1.Cover

3.Modelandserialnumber

plate

2.Pump

ModelNo.

SerialNo.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3391-742*A

Summary of content (16 pages)

PAGE 1
Form No. 3391-742 Rev A Tank Clean Rinse Kit Multi Pro® WM Turf Sprayer Model No. 41241—Serial No. 315000001 and Up Operator's Manual Note: Determine the left and right sides of the machine from the normal operating position. WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.
PAGE 2
Safety • Obtain proper training before using or handling Also read the safety and operation instructions in the vehicle Operator’s Manual. • Use the correct chemical for the job. chemicals. • Follow the chemical manufacturer's instructions for the safe application of the chemical. Chemical Safety • Handle chemicals in a well-ventilated area. • Wear goggles and other protective equipment as WARNING instructed by the chemical manufacturer.
PAGE 3
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 7 Description Use Qty.
PAGE 4
CAUTION 1 Chemicals are hazardous and can cause personal injury. Preparing the Machine • Read the directions on the chemical labels before handling the chemicals, and follow all manufacturer recommendations and precautions. No Parts Required • Keep chemicals away from your skin. Should contact occur, wash the affected area thoroughly with soap and clean water. Procedure 1. Move the sprayer onto a level surface, set the parking brake, stop the pump, stop the engine, and remove the ignition key.
PAGE 5
Figure 3 1. Filler cap 4. Wire 2. Flanged seal 5. Filler opening (rinse tank) 3. Bulkhead fitting 6. Bottom hole (rinse tank) Figure 4 1. Filler cap 3. Bottom hole of the rinse tank 2. Bulkhead fitting (with wire attached) 2. Remove the filler cap from the rinse tank (Figure 3). 4. Move the bulkhead fitting into position, ensuring that the O-ring seats against the interior wall of the rinse tank (Figure 4). 3.
PAGE 6
Figure 6 1. Bulkhead fitting 3. 90° barbed fitting 2. Fork pin 4. O-ring 3 Figure 7 Installing the Rinse Tank Parts needed for this procedure: 2 Rinse-tank bracket 2 Rinse-tank strap 2 Bolt (3/8 x 3 inch) 4 Flange locknut (3/8 inch) 4 Large washer 4 Carriage bolt (3/8 x 3/4 inch) 1. Bolt 4. Flange locknut 2. Washer 5. Carriage bolts (3/8 x 3/4 inch) 3. Strap 6. Slot Note: Retain all parts. 2.
PAGE 7
Install the Rinse Tank 4 1. Install the rinse tank as shown in Figure 8. Note: If there is not enough space for the rinse tank, loosen both of the main tank straps, and slide the main tank rearward. Installing the Rinse Nozzles Parts needed for this procedure: 2 Rinse nozzle 2 Bulkhead fitting 2 Shoulder bolt 2 Bushing 2 Rinse vane 2 90° barbed fitting 2 Plastic-flange nut Drilling the Main Tank 1. Remove the tank lid and the strainer basket from the sprayer tank (Figure 9). Figure 8 1.
PAGE 8
Installing the Rinse Nozzles 1 1. Assemble the 2 rinse nozzles as shown in Figure 10. 2 1 2 G022283 Figure 12 3 1. 90° barbed fitting 2. Nozzle assembly 4 5. Direct the hose barbs toward the middle of the right side of the machine. 5 6. Install the tank lid and the strainer basket to the tank that you removed previously. G022281 Figure 10 1. Bulkhead fitting 4. Rinse vane 2. Rinse nozzle 3. Bushing 5. Shoulder bolt 5 Installing the Pump 2.
PAGE 9
6 Installing the Hoses and Filter 1 2 Parts needed for this procedure: 3 4 1 Filter 1 T-fitting 1 15 cm (6 inch) hose 1 101.5 cm (40 inch) hose 1 42 cm (16.5 inch) hose 2 61 cm (24 inch) hose 9 Hose clamp 1 Grommet 1 90° barbed fitting (rinse tank) 1 Retainer 1 Rinse-pump cover 2 Hair pin G022291 Figure 13 1. Tank strap 3. Mounting bracket 2. Carriage bolt (3/8 x 3/4 inch) 4. Flange locknut (3/8 inch) 2.
PAGE 10
1 2 2. Assemble the other end of the hose to the barbed fitting of the rinse-pump filter, and secure the hose to the filter with a hose clamp (Figure 16). 1 Note: Ensure that the arrow on the filter points toward the T-fitting. 3. Assemble the 15 cm (6 inch) hose to the barbed fitting at other side of the rinse pump filter, and secure the hose to the filter with a hose clamp (Figure 16). 4.
PAGE 11
A G022144 1 Figure 18 1. Retainer B 3. 90° barbed fitting (rinse tank) 2. Bulkhead fitting 3. Route the hose 101.5 cm (40 inch) through the previously installed gasket in the side of the frame (Figure 17). 2 3 4. Assemble the end of the hose to the straight-barbed fitting at the inlet port of rinse pump, and secure the hose to the pump with a hose clamp (Figure 17). G024048 Figure 19 1. Plug 5.
PAGE 12
Product Overview water-soluble chemicals that occur when chemicals are not properly introduced into the main tank. Controls Filling the Tank The rinsse pump for the Tank Cleanse Rinse Kit is controlled by the 3 position switch. Rinse tank capacity: 76 L (20 gallons) Important: The rinse tank is only intended to be filled with clean water. Introducing any other substance to the tank can cause a safety hazard and/or damage the machine. 1.
PAGE 13
Storage • Spray the rinsate through the booms until the main tank is empty. • Drain the main tank contents into a suitable Drain the pump inlet line, outlet line, and filter line prior to storage for 30 days or more. container and dispose of the diluted solution as required by federal, state or local regulations. You can repeat the rinse cycle again as necessary or for 2 additional timed-rinse cycles.
PAGE 14
Declaration of Incorporation Model No. 41241 Serial No. Product Description Invoice Description 315000001 and Up Tank Cleanse Rinse Kit, Multi Pro WM Turf Sprayer TANK CLEAN RINSE KIT - MPWM General Description Directive Turf Sprayer 2006/42/EC, 2004/108/EC Relevant technical documentation has been compiled as required per Part B of Annex VII of 2006/42/EC. We will undertake to transmit, in response to requests by national authorities, relevant information on this partly completed machinery.
PAGE 15
International Distributor List Distributor: Country: Phone Number: Distributor: Phone Number: 57 1 236 4079 Colombia Japan 81 3 3252 2285 Czech Republic 420 255 704 220 420 255 704 Slovakia 220 Argentina 54 11 4 821 9999 Russia 7 495 411 61 20 Ecuador 593 4 239 6970 Finland 358 987 00733 Agrolanc Kft Balama Prima Engineering Equip. B-Ray Corporation Hungary Hong Kong Korea 36 27 539 640 852 2155 2163 82 32 551 2076 Maquiver S.A. Maruyama Mfg. Co. Inc. Mountfield a.s.
PAGE 16
Toro General Commercial Product Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).