Operator's Manual

ManualsBrandsToro ManualsSprayersChemical Pre-Mix Kit, Multi Pro WM Turf Sprayer

FormNo.3393-299RevA

ChemicalPre-MixKit

MultiPro

WMTurfSprayer

ModelNo.41244—SerialNo.315000001andUp

Operator'sManual

Thiskitisdesignedtoaidinthemixingofchemicalsin

preparationforturfsprayapplicationsonwell-maintained

lawnsinparks,golfcourses,sportselds,andoncommercial

grounds.Itisadedicatedattachmentforaturfspray

applicationvehicleandisintendedtobeusedbyprofessional,

hiredoperatorsincommercialapplications.

ThisproductcomplieswithallrelevantEuropeandirectives;

fordetails,pleaseseetheseparateproductspecicDeclaration

ofConformity(DOC)sheet.

Readthismanualcarefullytolearnhowtooperateand

maintainyourproductproperly.Theinformationinthis

manualcanhelpyouandothersavoidinjuryandproduct

damage.AlthoughTorodesignsandproducessafeproducts,

youareresponsibleforoperatingtheproductproperlyand

safely.

YoumaycontactTorodirectlyatwww.Toro.comforproduct

safetyandoperationtrainingmaterials,accessoryinformation,

helpndingadealer,ortoregisteryourproduct.

Wheneveryouneedservice,genuineToroparts,oradditional

information,contactanAuthorizedServiceDealerorToro

CustomerServiceandhavethemodelandserialnumbersof

yourproductready.Figure1illustratesthelocationofthe

modelandserialnumbersontheproduct.

Figure1

1.Modelandserialnumberplate

ModelNo.

SerialNo.

WARNING

CALIFORNIA

Proposition65Warning

Thisproductcontainsachemicalorchemicals

knowntotheStateofCaliforniatocausecancer,

birthdefects,orreproductiveharm.

Useofthisproductmaycauseexposureto

chemicalsknowntotheStateofCalifornia

tocausecancer,birthdefects,orother

reproductiveharm.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3393-299*A

Summary of content (16 pages)

PAGE 1
Form No. 3393-299 Rev A Chemical Pre-Mix Kit Multi Pro® WM Turf Sprayer Model No. 41244—Serial No. 315000001 and Up Operator's Manual This kit is designed to aid in the mixing of chemicals in preparation for turf spray applications on well-maintained lawns in parks, golf courses, sports fields, and on commercial grounds. It is a dedicated attachment for a turf spray application vehicle and is intended to be used by professional, hired operators in commercial applications.
PAGE 2
Safety WARNING Chemical substances used in the spray system may be hazardous and toxic to you, bystanders, animals, plants, soils or other property. • Carefully read and follow the chemical warning labels and Material Safety Data Sheets (MSDS) for all chemicals used and protect yourself according to the chemical manufacturer's recommendations.
PAGE 3
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Use Qty. 1 Support frame assembly Flange nut (3/8-16 inch) Back-plate assembly Cradle arm, right Cradle arm, left Bushing, small Pivot pin Jam nut (3/8 inch) Handle Bolt (3/8 x 1-1/4 inches) Set screw Hair pin Flat washer Thick square spacer Thin square spacer Carriage bolt (3/8 x 1-1/2 inch) 1 2 1 1 1 2 2 2 2 2 2 2 2 2 2 2 Assemble the frame. 2 Spring 2 Install the latching components.
PAGE 4
1 Assembling the Frame Parts needed for this procedure: 1 Support frame assembly 2 Flange nut (3/8-16 inch) 1 Back-plate assembly 1 Cradle arm, right 1 Cradle arm, left 2 Bushing, small 2 Pivot pin 1. Main support frame assembly 2 Jam nut (3/8 inch) 2. Guide plate 2 Handle 2 Bolt (3/8 x 1-1/4 inches) 2 Set screw 2 Hair pin 2 Flat washer 2 Thick square spacer 2 Thin square spacer 2 Carriage bolt (3/8 x 1-1/2 inch) Figure 3 3. Square spacer 6.
PAGE 5
Figure 6 1. Left cradle arm 2. Pivot housing 3. Set screw 4. Holes in cradle arm Figure 5 1. Back-plate assembly 7. Handle 2. Hair pin 8. Bolt (3/8 x 1-1/4 inches) 3. Flat washer 9. Right cradle arm 4. Bushing 2 10. Main-support-frame assembly 5. Pivot pin 11. Cradle-arm axle 6. Jam nut (3/8 inch) 12. Pivot housing Installing the Latching Components Parts needed for this procedure: 11. Loosely attach the left arm to the exposed axle on the other side of the frame. 2 12.
PAGE 6
4. Repeat 1 through 3 for the other side. 3. Tighten the fasteners in the tongue to secure its position, then release pressure on the back plate. 5. Tighten the 2 set screws in the left arm. Note: Check to see if there is any play in the cradle. It should be held snug to the frame assembly. You can repeat this procedure once the eductor is installed to adjust the locked position. Adjusting the Tongue Position Move the cradle assembly into the upper, transport position to adjust the tongue.
PAGE 7
raised up into the transport position. This will allow for further adjustment. 6. Check the eductor height on the cradle back plate and adjust as necessary. 7. Tighten the fasteners securing the eductor to the cradle. Note: Torque the fasteners to 36-45 N-m (27-33 ft-lb). 8. Tighten the 2 set screws on the left hand pivot arm. 9. Check the overall position of the eductor assembly on the tank strap. Note: The eductor should be upright, in the transport position.
PAGE 8
2. Use a 9 cm (3-5/8 inch) hole saw to drill a hole at the drill mark (Figure 13). Note: You will need to increase the diameter slightly to accommodate the bulkhead. 3. After drilling the hole, remove any rough edges in the cut, and remove any debris that entered the main tank during the cutting process. Installing the Bulkhead 1. Open the main tank lid and remove the filter screen. 2. Install the bulk head and the O-ring up from inside the tank through the previously cut opening (Figure 14). Figure 16 1.
PAGE 9
Figure 18 1. Eductor 2. Gasket 3. Hose 4. Hose clamp 5 Installing the Eductor Valve Assembly Figure 19 Parts needed for this procedure: 2 Retainer pin 1 Valve bracket 1 Eductor valve 1 Pressure hose assembly 1. Elbow 2. Flange clamp 5. Eductor valve 6. Nut 3. Gasket 4. Valve bracket 7. Bolt 2. Place the valve bracket on top of the eductor valve as shown in Box B of Figure 19. 3. Install the eductor valve using the gasket and flange clamp removed in Step 1; refer to Box B of Figure 19.
PAGE 10
6 Finishing the Installation Parts needed for this procedure: 1 Suction lance and hose (optional accessory) Procedure Figure 20 1. Hose clamp 4. Hose clamp 2. Retainer pin 5. Retainer pin (existing) Note: The suction lance and hose are optional accessories. Contact your Authorized Toro Distributor for more information. 3. Pressure hose assembly Retain the suction lance and hose for later use. Read and retain the remaining documentation on using the Chemical Pre-Mix Kit. 6.
PAGE 11
Handles and Transport Strap Operation Use the upper and lower handles to raise and lower the eductor and to lock it into the transport position. CAUTION Chemicals are hazardous and can cause personal injury. Main Valve Use the main valve to introduce chemicals from the eductor into the hose leading to the main tank. • Read the directions on the chemical labels before handling the chemicals and follow all manufacturer recommendations and precautions.
PAGE 12
Raising the Eductor Starting the Eductor 1. Lift the lower handle to raise the eductor while slightly tipping it toward the tank. Note: Close the eductor hopper valve and hopper rinse ball valve(s) before starting the eductor. 2. Guide the tongue under the cross bar with the welded tab in the upper portion of the frame assembly. 1. Lower the eductor. 2. Open the lid to check for foreign objects which may hinder performance or contaminate the system. 3.
PAGE 13
Figure 24 1. Suction lance 2. Eductor 2. Use the free end of the lance to pierce the bag or container to vacuum powdered or liquid chemical. 3. Place the lance end into a clean container of water to rinse the lance assembly. 4. Remove the lance body from the eductor and drain any remaining fluid into the hopper. 5. Close the hopper valve (red handle). Shutting Down the Eductor 1. Close the hopper valve, then close all the remaining valves. 2. Remove all chemical residue. 3.
PAGE 14
Troubleshooting Problem The eduction rate is low. Possible Cause 1. There is a lack of flow and pressure to the eductor system. 1. Increase the pump speed. Turn the agitation throttling toward the closed position. 2. The outlet/Inlet hose is obstructed. 2. Disassemble and remove any obstructions. 3. Use only sweeping turns with flexible hoses. 3. Fittings with elbows or other flow-restrictions are in the eductor outlet. There is no rinsing or flushing action. There are leaks at the fittings.
PAGE 15
International Distributor List Distributor: Country: Phone Number: Distributor: Phone Number: 57 1 236 4079 Colombia Japan 81 3 3252 2285 Czech Republic 420 255 704 220 420 255 704 Slovakia 220 Argentina 54 11 4 821 9999 Russia 7 495 411 61 20 Ecuador 593 4 239 6970 Finland 358 987 00733 Agrolanc Kft Balama Prima Engineering Equip. B-Ray Corporation Hungary Hong Kong Korea 36 27 539 640 852 2155 2163 82 32 551 2076 Maquiver S.A. Maruyama Mfg. Co. Inc. Mountfield a.s.
PAGE 16
Toro General Commercial Product Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).