Installation Instructions

ManualsBrandsToro ManualsAttachmentsPA-17 Spreader Frame Kit, Workman

Refer to the illustrated Parts Catalog for the de-

tails of parts used in assembling the Workman

Spreader Frame Kit.

NOTE: Right, Left, Front and Rear are

reference while seated in the operators posi-

tion.

1. Install the TORO APU Electric Clutch Kit as

per the instructions provided with that kit.

2. Remove top and sides of crate. Remove the

lag screw at the Frame Mounting Bracket to re-

move the Crate skid.

NOTE: The optional Flow Control Kit (Model

No. 41403) should be installed on the PA-17

Spreader BEFORE the Spreader is attached

to the mounting frame. (FIG. 1) See the Set-

Up and Parts Catalog furnished with the Flow

Control Kit for the installation instructions.

3. Remove the Drive Shaft Cover and position

the Spreader onto the Mounting Frame.

4. Use lacquer thinner to remove the rust pre-

ventative coating from the Spreaders in-put shaft

and keyway. Insert the 1/4" square key into the

in-put shaft. See FIG. 1.

FIG. 1

1. Spreader In-Put Shaft 3. Optional Flow

2. End Yoke Control

5. Align the Spreader in-put shaft with the End

Yoke and slide the Spreader forward until the End

Yoke is fully engaged on the in-put shaft. DO

NOT TIGHTEN the set screw at this time.

FORM NO. 92-8237 REV. A

MODEL NO. 41252-90001 & UP

PA-17 WM FRAME KIT & SPREADER

FOR THE WORKMAN

VEHICLE

SET-UP AND

PARTS CATALOG

6. Loosen the fasteners on the Frames mount-

ing straps and align the hole in the Spreaders

rear mounting plate with the hole in the Mount-

ing Frame as shown in FIG. 2. Insert a 5/8" x 2"

bolt with washer through the holes to maintain

the alignment of the Spreader in-put shaft and

End Yoke.

FIG. 2

1. Rear Mounting Plate 2. U-Bolts

7. Align Frames mounting mounting straps with

the mounting lugs on the front of the Spreader.

Secure the Spreader to the straps with two 5/8" x

2-1/2" bolts, eight washers and two hex nuts. See

FIG. 3. Re-tighten mounting straps fasteners.

1. Mounting Straps 3. Cross Member

2. Mounting Lugs

FIG. 3

1398

1399

1397

Summary of content (8 pages)

PAGE 1
FORM NO. 92-8237 REV. A SET-UP AND PARTS CATALOG MODEL NO. 41252-90001 & UP PA-17 WM FRAME KIT & SPREADER FOR THE WORKMAN Refer to the illustrated Parts Catalog for the details of parts used in assembling the Workman Spreader Frame Kit. NOTE: Right, Left, Front and Rear are reference while seated in the operators position. 1. Install the TORO APU Electric Clutch Kit as per the instructions provided with that kit. R VEHICLE 6.
PAGE 2
8. Lift and secure the Mounting Frame and Spreader approximately 12 inches above ground level for easier access to fasteners used in securing the Spreader to the Mounting Frame. 9. Install hex nut and washer to 5/8" x 2" bolt at rear mounting plate. See FIG. 2. 10. Insert two U-bolts over the tubular frame of the Spreader and secure with four 3/8" flat washers and lock nuts (FIG. 2). 16. Secure the Mounting Frame to the Attachment Mounting Brackets with two 1/2" x 1-1/2" bolts four washers and lock nuts.
PAGE 3
NOTE: If the Spreader IS EQUIPPED with the optional Flow Control Kit, skip Steps 1 thru 6 and proceed to Step 7. If the Spreader is NOT EQUIPPED with the optional Flow Control Kit, proceed as follows: 1. Install the Lever Bracket Assembly on the Workmans Seat Frame as shown in FIG. 7. Secure with four 5/16" x 3/4" carriage bolts and nuts. 1403 1. Lever Bracket Assy 2. Seat Frame 3 Flow Regulator Handle (in Close Position) 7.
PAGE 4
. Disconnect the Wiring Harness at the Actuator and the two Limit Switches. 1405 1. Capacity 700 LBS. Decal FIG. 9 2. Maximum Sand Level Decal 12. Remove the backing and affix the Capacity 700 LBS. Decal over the Capacity 1000 LBS. Decal, so it is completely covered. INSTRUCTIONS FOR SPREADER EQUIPPED WITH THE OPTIONAL FLOW CONTROL KIT: 1. Remove two screws on the Workman dash panel and use them to attach the Control Console Bracket to dash as shown in FIG. 10. 1407 1. Limit Switch FIG. 11 2.
PAGE 5
WARNING ROTATING MEMBERS 80-8040 1409 SPREADER DRIVE Ref Part No. Description Qty Ref Part No.
PAGE 6
THESE PARTS ARE NOT USED WITH OPTIONAL FLOW CONTROL KIT. 1410 45 47 46 TO AVOID PERSONAL INJURY KEEP ALL SHIELDS IN PLACE. DISENGAGE AND SHUT OFF ENGINE BEFORE SERVICING OR UNCLOGGING MACHINE. KEEP HANDS, FEET AND CLOTHING AWAY FROM POWER-DRIVEN PARTS. Part No. 65-3090: Located on top of Front Tube Crossmember. Part No. 75-5190: Located on rear Rear Cover 2 - Located on sides of Rear Support Tube. 2 Located on Radiator Cver. 53 51 Part No. 36-3400: Located on Radiator Cover.
PAGE 7
SPREADER DRIVE Ref Part No. Description 1 92-8229 2 32153-5 Lock Nut, 1/2 NC 3 92-8228 4 3230-1 5 92-8223 6 92-8230 7 32153-15 8 327-4 9 92-8235 Pivot Sleeve 10 3256-6 Flat Washer, 1/2 USS 11 325-17 12 3220-5 13 92-0302 14 328967 15 283-68 16 92-8231 17 32104-57 Qty Ref Part No. Description Qty 1 30 325-13 HHCS, 1/2 NC x 3-1/4 4 11 31 92-8291 Frame Ass'y.
PAGE 8
1411 GEAR MULTIPIER, 5:1 REF 8 PART NO. DESCRIPTION QTY 1 43047 250 Housing Half 1 2 43048 250 Housing Half 1 3 43049 250 Gear, INTG HEL LH, 15T 1 4 43050 250 Gear, HEL RH , 75T 1 5 43051 250 Shim, .002 Red 2 6 43052 250 Shim, .005 Blue 2 7 43053 Spec.