Quick Start Guide

ManualsBrandsToro ManualsSprayersGeoLink CDMA Precision Spray System Kit, Multi Pro 1750 or 5800 Turf Sprayer

FormNo.3433-789RevB

X25GeoLink

PrecisionSpraySystemKit

SoftwareVersion4.04

QuickStartGuide

ContactToroNSNat1-844-GEOLINK(1-844-436-5465)orGeoLinkNSN@toro.comforcustomerservice.

Note:ThedisplayisinSTANDARDMODEafterstartup.Tochangemodes,refertotheGeoLinkOperator’s

Manual.

Note:Usetheignitionkeyofthemachinetorunorshutoffthedisplay,receiver,andsectioncontroller.

UsingtheTouchScreen

Sprayerinformationdisplaysonthescreenwhenyoutouchandenabletheindividualicons.

•Pressanyicononthescreentodisplaywhatisshownonthescreen.

•Pressonanicontoselectafunction,andtherelatedoptionsdisplay.

•Presstheoptionsasrequired,andpressthegreencheckboxiconforthenewdisplay.

g294063

Figure1

g294048

Figure2

Standard-ModeHomeScreenShown

1.System-informationicon6.Sprayer-controllericon

11.Receivercalibrationicon16.Display-viewicon

2.Guidanceicon

7.Inventory-managericon12.Job-menuicon17.Map-layersicon

3.GPSicon8.Setupicon

13.Field-menuicon

18.Center-mapview

4.Job-informationicon

9.Displaydashboard

14.Quick-starticon

19.Boundary-selectionicon

5.Auto-sectioncontrolicon10.Master-switchicon

15.Zoom-functionicon20.Section-displayicon

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3433-789*B

Summary of content (4 pages)

PAGE 1
Form No. 3433-789 Rev B X25 GeoLink® Precision Spray System Kit Software Version 4.04 Quick Start Guide Contact Toro NSN at 1-844-GEOLINK (1-844-436-5465) or GeoLinkNSN@toro.com for customer service. Note: The display is in STANDARD MODE after startup. To change modes, refer to the GeoLink Operator’s Manual. Note: Use the ignition key of the machine to run or shut off the display, receiver, and section controller.
PAGE 2
Identifying the Software Version Creating a New Field Boundary Press the Toro icon at the top, left corner of the screen to display the software version. Note: The boundary is created at the outside, center of the front, left tire. g294392 Figure 6 g294808 Figure 3 Using Quick Start 1. Drive to the field area of the job site. 2. Press the field-menu icon. Press the quick-start icon (Figure 2) and a wizard walks you through the steps in this guide. g294470 g294615 Figure 7 Figure 4 1.
PAGE 3
4. Press the region type icon, and select a categorized region, work region, exclude region, or disabled. 10. 5. Press the category icon and select a preset category or create a new category. 11. 6. Press the green check box icon green check box icon and then the right arrow icon. In the save product setting pop-up window, press the green check box icon. In the fill tank pop up window, press the yes or no icon to select the new product for sprayer tank. g294821 Figure 8 1.
PAGE 4
8. Note: The display shows spray active areas in light gray shading and non-spray areas in dark gray shading. If the display shows all light gray, you can spray the entire area. To start spraying, press the master switch to the position (Figure 16). ON 9. Press the section switches (located between the seats) to the ON position (Figure 16). Note: The machine starts spraying when the sprayer crosses into the correct spray area.