MODEL NO. 41355 & 41360 CE and up FORM NO.
MULTI-PRO® 12001250 & 5600 BOOM FRAME ASSEMBLY: MULTI-PRO® 120011250 1. Remove Stop Pins in Boom Mount Assemblies. Apply a heavy coating of grease to the tubes of the two Boom Mount Assemblies and insert them into the Vehicle Frame until Angle Gusset bottoms out against Vehicle Frame. {See FIG. 1) MULTI-PRO® 5600 1. Apply a heavy coating of grease to the tubes of the wo Boom Mount Assemblies and insert them into the Vehicle Frame, as shown in FIG. 1, until the Stop Pins hit the frame tube. MULTI-PRO® 1.
CENTER ASSEMBLY: 1. Assemble Boom Mount onto the Center Boom as per FIG. 4 using the (6) 1/2" x 3" hex hd. cap screws and lock nuts. FIG, 4a, BOOM MOUNT Hoodie MULTI-PRO® 1200, 1250 & 5800 N WORKMAN® Fig. 4h 1. Boom Center Section 2. Boom Mount 2. Assemble the (2) straight Castor Mounts into Center Born section, using (4) 1/2" x 3" carriage hd. bolts and lock nuts, ensuring that bolt heads are on the "hood opening” side. Assemble (2) Wheels onto (2) Castor Forks with the long shafts using (2) 3/4™ O.D.
3. Lightly grease Right and Left Boom horizontal pivots where bushings will rotate. Assemble Right and Left Booms onto Boom Center Section / Horizontal Pivot Joint as per FIG, 5 ensuring that bushings are properly seated. Torque the wing retainer jam nut to 15 ft. Ibs and lock with second Jam nut. 4. Assemble (2) Anti-scalp Castors onto back outer mount on Right and Left Booms using (2) 7/16* lock nuts.
The Boom hose connection will depend on the type of Control Valve system used on the Sprayer. Refer to the applicable SPRAY SYSTEM SET-UP AND PARTS MANUAL for the Control Valve installation. SPRAYERS WITH ELECTRIC CONTROL VALVE SYSTEM: 1, Connect the 34" length of 3/4” Hose included with the Boom to the inlet on the Center Boom Flow Mentor and the other end to the outlet on the center Valve, Secure with Hose Clamps. 2.
The Wiring Harness installation will depend on the Vehicle and type of Sprayer. Refer to the applicable installation instructions, MULTI-PRO® 5800 WIRING HARNESS INSTALLATION: 1. Remove the Panel Assembly from the Center Console Assembly. See FIG. 8. center sockets. Insert the Green / White Wires into the corner sockets with the Green or White wire, Plug the remaining Yellow / Blue Wires into the other corner sockets, (these sockets will have a Blue or Yellow wire), Repeat this step for the other Plug.
5. Route the Boom Lift Harness to the rear of the Vehicle along the right side of the main frame, following the marry wiring harness through the cable dings. 6. Reinstall the Panel Assembly to the Center Console Assembly. 7. From the Back of the Vehicle, route the leads for the Right and Left Boom Actuators along the Boom Feed Hoses and out where the actuators will be located. WORKMAN® WIRING HARNESS INSTALLATION WITH THE WORKMAN® SPRAY SYSTEM: 1.
MP1250 FIG. 110 1. Rocker Switch 3. Plug 2. Notch (at back) 4. Spray Control Panel 2. Lift and remove the two plugs from the Spray Control Panel on the vehicle and install the two Rocker Switches provided in their place. Insure their orientation matches the orientation in Fig. 11a or 11b with the notch to the rear of the Vehicle. This notch indicates the end of the switch to which the locking Arm will mate. 3.
ELECTRIC BOOM EXTENSION LIFTS: 1. Assemble the Boom Extension Electric Lift Adjustment Links onto the Right and Left Boom Extensions using /2" x 8 1/2” hex hd. cap screws and knockouts. Assemble Electric Actuators onto the Boom Extension Breakaway Pivots using the 1/2" x 5" hex hd. cap screws and knockouts. Connect the other end of the Actuator to the Actuator Adjustment Link using the 1/2” x 2" hex hd. cap screws and lock nuts. FIG 14.
7.1f the measurement is incorrect, remove the hex hd screw that attaches the Actuator Adjustment Link to the Actuator, loosen the Jam Nut and rotate the Adjustment Link to change the length to the specification. Replace the hex hd screw and nut ensuring that the Adjustment Link can pivot freely. Re tighten the Jam Nut, ensuring that the Link rests squarely on the Actuator Link Stop in the raised position.
DRIFT SEAL INSTALLATION: NOTE: If the Enclosed Boom must be transported at highway speeds to the end use location the Drift Seal should be installed at the end use location to prevent wind damage. 1. Assemble the Drift Seal sections into the Retainer Molding slots located on the lower edge of the Boom. The longer pieces will be easier to install if a light lubricant such as liquid soap or a silicone based product {i.e. Armour All) is used. (FIG.
A warning This attachment may cause the overall gross vehicle weight to be exceeded when used in combination with other attachments Exceeding the grass vehicle weight can cause injury or death due to reduced handing, braking and stability. Always reduce payload to maintain vehicle weight within gross vehicle wait rating. See OPERATOR'S MANUAL for additional information. FIG.18 1.
SAFETY, INSTRUCTION AND IDENTIFICATION DECALS SPAY BOOM CONTROL 38870 el 820860 Part No. 84-8701 Part 221 d Located on Center Section Ends and on Boom sn Extension Hoods near Actuator Link. Located on the Switch Bracket ANAL T Part No. 94-8702 Located on Boom Extension curved Castor Wheel Mount S175 4.8, Gat S158 U8, Gal 56620 <587 L Part No. 94-8608 WORKMAN® Vehicle only Located on either side of the rear Spray Tank Band and Hose Reel, if equipped with ane.
FRAME & SHROUD GROUP {Not shown} Main Frame Right inner Shroud Cap Left Boom Extension Boom Extension Shroud Hood Cuter End Cap Shroud Boom Extension Left Bumper Strip Drift Seal Retainer Boom Extension Front Inner Drift Seal Retainer Boom Extension Front Quire Drift Seal Retainer Boom Extension Hood Ref | Part No. Description Ref | Part No.
18 FRAME & SHROUD GROUP BOOM EXTENSION PIVOT JOINT GROUP Ref i Part No. Description Qty’ Ref | Part No.
WHEEL MOUNT & WHEEL GROUP FOAM MARKER OPTION Ref| Part No. Description Cty' 4 Ba-8652 stir Fork Anti-Ascella 48 32146-7 |Lock Nut, 716 NC 2 49 948877 1 Whee! Anti-Scalp 5 O.0.
MOUNT Ref| Part No. Description Qty T 520127 3200, 7250, 560078 WORKMAN Noun Asm] 7 2 3255 [Hex hd cap screw, 12 NCx 9 3 32512 [Hex hd cap strew 1/2° NCx 3214613 lock Nut, 948673 | Flow Monitor Mount Extender 1 Bracket MP 5600 8 95-2008 | Flow Monitor Aunt Spacer 318" 7 302:19. [ Grease. Perk » 147 NF.
DRIFT SEAL RETAINER, DRIFT SEAL AND TRIM GROUP Ref [ Part No. Ascription Qty T S-2007 | Uit Seal Retainer Carter Boom T Front 2 952002 | Drift Seal Re fainer ~ Center Boom 1 Hood 3 952003 | Drift Seal Retainer Center Boom 2 Rear 4 94-8797 | Drift Seal Retainer Boom Extension 2 Rear Inner 26" 5 94:8798 | Deft Seat Retainer Boom Extension 1 Rear Outer Left 73.
ELECTRIC ACTUATOR j =L IEC Part No.
Not used on MULTI-PRQ® 1200, 1250, 5600 and WORKMAN® ACTUATOR WIRING HARNESS Ref Part No, Description 94-8558 30954 30955 100-7082 100-7091 Wiring Harness Toggle Switch ciw Nut Rubber Boot Fuse 30 Amp Slow Blow Power Wire Extender
PLUMBING GROUP 3/4" Up to serial # 80160 Description Qty 000 [Nozzle Body Assembly See Del all T Parts Breakdown 848710 [Nobody Mounting Howe, pairs " 94-8778 Hose Center Baum Flow Monitor Feed & Extension Boom Outer 3 Nozzle Feed" 94-8779 j Hose Center Boom Right Nozzle 1 Feed 66" 948780 [Hose Center Boom Center Nozzle 1 Feed 78" 94-8781 |Hose Center Boom Left Nozzle 1 Feed 119" 94-8782 {Hose Extension Boom Flow Monitor 2 Feed 174" 8 94.
PLUMBING GROUP 1/2” Serial # 90161 and up Description 100-6863 94-8710 94-8778 100-6856 100-6855 100-6854 94-8782 100-6857 100-6858 1006859 6609 2412:36 $5-2073 100-6860 Nozzle Body Assembly See Logan Pans Breakdown Nozzle Body Mounting Hardware pars Hose Center Boom Flow Monitor Feed 34° Hose Center Boom Right Nozzle Feed 128 Hose Center Boom Center Nozzle Feed 88° Hose Center Boom Left Nozzles Feed 78" Hose Extension Boom Flow Monitor Fed 174" Hose Extension Boom Inner Nozzle Feed 69 1w Hose Extension
NOZZLE BODY ASSEMBLY Up to serial # 90160 ¥ i Ref| Part No. Description Gty 1 41066 | Homebody L Type Says In chides. 1 Nozzle body 1 of Diaphragm 1 of Diaphragm Cap (18 psi) 952452 schnozzle L Type Says Includes 1 Nozziehody 1 of Diaphragm 1 of Diaphragm Cap (20 1 of Used on Enclosed Boors with Serial No.
FLOW MONITOR Up to serial # 90160 EXTENSION BOOM FLOW MONITOR CENTER BOOM FLOW MONITOR Ref| Fast No.
FLOW MONITOR Serial #'s 90161 to Ref{ Part No.
FLOW INDICATOR Modular Serial # CE and up Ref | Part No.