Operator's Manual

ManualsBrandsToro ManualsSprayersEnclosed Boom, Multi-Pro 1100

©The TORO Company - 2001

ENCLOSED BOOM

for the MULTI PRO

1200, 1250, 5500 and WORKMAN

Vehicles

FOREWORD

You have purchased a product from the industry leader in maintenance excellence. Its future performance

and dependability are of prime importance. TORO is also concerned about future use of the product and of

safety to the user. Therefore, this manual must be read by you and those involved with the ENCLOSED

BOOM to assure that safety, proper set-up, operation and maintenance procedures are followed at all

times. The major sections of the manual are:

1. SAFETY INSTRUCTIONS 2. OPERATING INSTRUCTIONS 3. BEFORE SPRAYING

4. MAINTENANCE AND STORAGE

Safety, mechanical and some general information in this manual are emphasized. DANGER, WARNING

and CAUTION identify safety messages. Whenever the triangular safety symbol appears, it is followed by

a safety message that must be read and understood. For more details concerning safety, read the Safety

Instructions on this page and page 2.

IMPORTANT identifies special mechanical information and NOTE identifies general information worthy of

special attention. These instructions are provided as a guide for the safe operation and maintenance of this

equipment. However, the operators personal safety, as well as the persons in the work area, will depend

on the careful actions and good judgement of the operator. To reduce the potential for injury or death,

comply with the following safety instructions.

SAFETY INSTRUCTIONS

Keep this Operators Manual in the plastic tube behind the operator seat.

It is very important that all persons operating this equipment have easy access to these instructions at all

times!

Carefully read and follow the Set-up Instructions that are provided with this equipment and the Safety

Instructions in the MULTI-PRO

1200, 1250, 5500 or WORKMAN

Vehicle Manual and Spray Systems

Operators Manual.

To assure maximum safety, optimum

performance, and to gain knowledge of the

product, it is essential that you or any other

operator of this equipment read and

understand the contents of this manual before

the vehicle engine is ever started. Pay

particular attention to the SAFETY

INSTRUCTIONS highlighted by the triangular

safety alert symbol.

The safety alert symbol means CAUTION,

WARNING, or DANGER  personal safety

instruction. Failure to comply with the

instruction may result in personal injury.

BEFORE OPERATING:

1. Operate this machine only after reading and

understanding the contents of this manual.

A replacement manual is available by sending

complete model and serial number to: Hahn

Equipment Co., A subsidiary of The Toro Company,

1625 N. Garvin, Evansville, IN 47711

OPERATOR'S

MANUAL

FORM NO. 100-7076 Rev. A

MODEL NO. 41355 & 41360

200000101 CE and up

Summary of content (12 pages)

PAGE 1
FORM NO. 100-7076 Rev. A OPERATOR'S MANUAL MODEL NO. 41355 & 41360 200000101 CE and up ENCLOSED BOOM for the MULTI PRO® 1200, 1250, 5500 and WORKMAN® Vehicles To assure maximum safety, optimum performance, and to gain knowledge of the product, it is essential that you or any other operator of this equipment read and understand the contents of this manual before the vehicle engine is ever started. Pay particular attention to the SAFETY INSTRUCTIONS highlighted by the triangular safety alert symbol.
PAGE 2
SAFETY INSTRUCTIONS 2. Learn how to operate the Sprayer and how to use the controls properly. DO NOT let anyone operate this equipment without first receiving thorough instructions. 3. Keep all shields, safety devices and decals in place. If a shield, safety device or decal is malfunctioning, illegible or damaged, repair or replace it before operating the machine. 4. Chemicals can injure persons, animals, plants, soils or other property. To eliminate environmental damage and personal injury. A.
PAGE 3
SAFETY, INSTRUCTION AND IDENTIFICATION DECALS Part No. 94-8701 Located on Center Section Ends and on Boom Extension Hoods near Actuator Link. Part No. 92-2660 Used on WORKMAN only. Located on the Switch Bracket Part No. 94-8702 Located on Boom Extension curved Castor Wheel Mount Part No. 94-8609 WORKMAN® Vehicle only - Located on either side of the rear Spray Tank Band and Hose Reel, if equipped with one. Enclosed Boom - Located on rear left side of Center Section.
PAGE 4
BEFORE OPERATING WARNING This attachment may cause the overall gross vehicle weight to be exceeded when used in combination with other attachments Exceeding the gross vehicle weight can cause injury or death due to reduced handling, braking and stability. Always reduce payload to maintain vehicle weight within gross vehicle weight rating. MAXIMUM PAYLOAD NOTE: The following applies to the WORKMAN® Vehicle only. 1. Only fill the spray tank to 175 U.S. gallons (662L) total.
PAGE 5
BOOM EXTENSION FORWARD FOLD: CAUTION Use proper lifting procedures when lifting the Extension Boom into the forward fold position. Failure to follow proper lifting procedures could result in personal injury. Follow the Forward Fold Instructions Decal located near the end of the Boom Extension.
PAGE 6
FLOW MONITOR: 1. Each boom section has a flow monitor mounted in the operator's view. The monitors have sight tubes; each tube contains a weighted ball that floats when there is flow to the corresponding nozzle. 2. When there is flow, all the floating balls should be at the same level. If a ball is lower than the others, this indicates a clogged nozzle. See FIG. 3.
PAGE 7
3. If the measurement is incorrect, remove the hex hd screw that attaches the Actuator Adjustment Link to the Actuator, loosen the Jam Nut and rotate the Adjustment Link to change the length to the specification. Replace the hex hd screw and nut ensuring that the Adjustment Link can pivot freely. Retighten the Jam Nut, ensuring that the Link rests squarely on the Actuator Link Stop in the raised position.
PAGE 8
BEFORE SPRAYING IMPORTANT: The Enclosed Boom nozzle bar is fixed at 15" height and 20 inch spacing. Use only Flat Fan 1100 tips to maintain proper calibration. EXAMPLE (SI FORMULA) Application Rate = 907 L/hectare Vehicle Speed = 5 km/h Nozzle Spacing = 50 cm NOZZLE SELECTION 907 L/ha x 5 km/h x 50 60,000 See the SPRAY NOZZLE SELECTION CHART to be sure that your spray nozzles have the capacity necessary to achieve the application rate selected. With 3.78 G.P.M.
PAGE 9
SPRAY NOZZLE SELECTION CHART 7252 1R]]OH 3UHVVXUH &DSDFLW\ 3DUW 1R 1XPEHU 36,* 1R]]OH 03+ 03+ 03+ %URZQ
PAGE 10
NOTES: 10
PAGE 11
Helping you put quality into play.
PAGE 12
The Toro Promise A One Year Limited Warranty The Toro Company promises to repair your Model 41355 ENCLOSED BOOM for the MULTI-PRO® 1200, 1250, 5500 and WORKMAN® Vehicles if defective in materials or workmanship. The following time periods from the date of purchase apply special warranty terms, on certain components, may be offered through The Toro Company by the component manufacturers: Commercial Products...........................1 Year The cost of parts, labor and transportation are included.