MODEL NO. 41358 FORM NO. 94-8595 OPERATORS, SET-UP AND PARTS MANUAL L ENCLOSED WALKING BOOM To assure maximum safety, optimum performance, and to gain knowledge of the product, it is essential that you or any either operator of this equipment read and understand the contents of this manual before the product is used. Pay particular attention to the SAFETY INSTRUCTIONS highlighted by the triangular safety alert symbol. A The safety alert symbol means CAUTION, WARNING, or DANGER — personal safety instruction.
FOREWORD You have purchased a product from the industry leader in maintenance excellence. Its future performance and dependability are of prime importance. TOR is also concerned about future use of the product and of safety to the user. Therefore, this manual must be read by you and those involved with the ENCLOSED WALKING BOOM to assure that safety, proper set-up, operation and maintenance procedures are followed at ail times. The major sections of the manual are: 1.SAFETY INSTRUCTIONS 2.
NP os w0 FG1. . Upper Han die Section . Lower Handle Section tare Wheel Magnet Small Sheet Boom Extension Frame Main Boom Feed Hose 8. Speedometer 9. Boom Extension Cover 10. Retainer Knob 1. Shroud Lockup Pin 12. Drift Seal Retainer 13.
SET-UP INSTRUCTIONS Refer to illustrated Parts List for details of parts used in assembling the ENCLOSED WALKING BOOM. NOTE: "Right", "Left", "Front” and "Rear" are referenced while standing in the operator's position BOOM FRAME ASSEMBLY 1. Assemble the Upper Handle Section onto the Lower Handle Section using the (2) #10x 3/4" sheet metal screws to secure. 2. Assemble the {2) large wheels and handle onto the Center Boom using the (2) 1/2" x 8" hex hd. cap screws, spacers and lockouts.
BEFORE SPRAYING IMPORTANT: The Enclosed Boom nozzle bar is fixed at 15" height and 20 inch spacing. Use only Flat Fan 110° tips to maintain proper calibration. NOZZLE SELECTION See the SPRAY NOZZLE SELECTION CHART to be sure that your spar% nozzles have the capacity necessary to achieve the application rate selected. To select the proper nozzle, you need to know: 1. Recommended chemical application rate in gallons per acre, gallons per 1000 sq. f1. or liters per hectare. 2.
SPRAY NOZZLE SELECTION CHART TORE Nozzle | Pres sire | Capacity APPLICATION RATES FOR NOZZLES Part No, Number | (PSI) | 1-Nozzle 207 SPACING s color-Cos P GALLONS PER AGE GALLING PEATY 5, FT. color-Gotde MPH [ S MPR T EMF [ 6 MPH | MPH | 4 MPH | 5 MPH | 6 MPH KRTT00avS| 064 | 046 | 039 | 0.2 ! 1100 o78 | os0 | vas | v 94-8714 ose | 058 | o046 Bed 0.76 9.62 8.51 [Doritos] 17.6 | 080 | 0.60 | 048 | 0.40 o096 | 073 | 060 [ 048 94-8715 115 | oss | oee | o7 Brown 120 ) 096 Xri1006vS| 0.86 | 035 | 057 | 0.
OPERATING INSTRUCTIONS FLOW MONITOR: 1. The Flow Monitor has four sight tubes, each tube contains a weighted ball that floats when there is flow to the corresponding nozzle. 2. When there is flow, ali the floating balls should be at the same level. If a ball is lower than the others, this indicates a clogged nozzle. (FIG. 2) 3. if all the balls cannot be made to come up to the same level, check the flow in the lines to see if the flow is equal in all lines.
MAINTENANCE AND STORAGE FLUSH BOOM AFTER USE: 1. Flush the entire system with a solution that will chemically neutralize the liquid in the monitors. Mix according to manufacturers directions. This will dissolve most residue remaining in the monitor. NOTE: The flow monitors will discolor if proper flushing procedures are not adhered to. 2. The flow monitor is susceptible to discoloration if exposed to direct sunlight for several years.
WALKING BOOM FRAME AND SHROUD GROUP Ref | Part No, Description Gty Ref| Part No.
PLUMBING GROUP FLOW MONITOR GROUP 12 fled | Part No. Description Qty Ref| Part No.
FRONT OF BOOM LEFT BOOM EXTENSION RIGHT BOOM EXTENSION CENTER SECTION DRIFT SEAL RETAINER, DRIFT SEAL AND TRIM GROUP Ref | Part No. Description Gty Regret Part No.
o NOZZLE ASSEMBLY Detailed Parts Breakdown {Used on Center Section Right Side Not shown) Somebody 1 of Diaphragm 1 of Diaphragm Cap 1 of Ref | Part No. Description Qty Ref! Part No, Description Gty 1 41000 homebody L type Standard 2 2 G4B710 |Nozziebody Mounting Hdqrs.
The Toto Company promises to repair your Model 41358 ENCLOSED WALKING BOOM if defective in materials or workmanship. The following time periods from the date of purchase apply special warranty terms, on certain components, may be offered through The Toto Company by the component manufacturers: The Toto Promise A One Year Limited Warranty Commercial Products. 1 Year The cost of parts, labor and transportation are included.