Installation Instructions

ManualsBrandsToro ManualsSprayersSkid Sprayer

FORM NO. 93-6268

MODEL NO. 41411-50001 & UP

MODEL NO. 41020-50001 & UP

MODEL NO. 41120-50001 & UP

MODEL NO. 41021-50001 & UP

SET-UP AND

PARTS LIST

SKID SPRAYER

Refer to the illustrated Parts List for the details of parts used in assembling the SKID SPRAYER.

©The TORO Company - 1995

3. Apply thread sealer and install the 90° barbed

elbow into the bottom of the Tank. See FIG. 2.

NOTE: Position the barbed elbow as shown, so

that it will angle toward the muffler on the Skid

Sprayer engine after the Tank is installed on the

Skid Frame.

Note: Right and Left as used in the

following instructions, refer to the operators

right and left when seated in the normal

operating position.

Remove the Sprayer Skid from its shipping skid.

For ease of handling, while connecting the Hoses

to the Tank, disconnect the 1" x 53" Suction Hose

and the 1/2" x 45" Agitator Hose at their respective

Quick Couplers. See FIG. 1.

FIG. 1

1. Suction Hose 2. Agitator Hose

Quick Coupler Quick Coupler

TANK ASSEMBLY:

1. Cut the shipping straps and remove the

Spray Tank and Saddle Assembly from the ship-

ping skid.

2. Remove the two screws holding the Heat

Shield to the Tank Saddle and discard the Heat

Shield.

NOTE: In the following instructions, "thread

sealer" refers to Teflon thread tape.

FIG. 2

1. Barbed Elbow 3. Elbow & Quick

(Suction Line) Coupler (Overflow)

2. Spill-way 4. Mounting Member

4. Apply thread sealer and assemble the 90° St.

elbow to the male Quick Coupler. Install the elbow

into the fitting at the spill-way end of the Tank, so

that it angles toward the outside of the Tank as

shown in FIG. 2.

NOTE: If the Skid Sprayer is to be installed on

a Trailer, (as shown in FIG. 3), install the Elbow

and Quick Coupler in the Tank as shown in Detail

A of FIG. 2. If the Skid Sprayer is to be installed

on a Transport Vehicle (as shown in FIG. 4),

install the Elbow and Quick Coupler as shown

in Detail B of FIG. 2.

5. Loosen the hose clamp on the Suction Hose

and use it to secure the Hose to the barbed elbow

in the bottom of the Tank.

Summary of content (20 pages)

PAGE 1
FORM NO. 93-6268 MODEL NO. 41411-50001 & UP MODEL NO. 41020-50001 & UP MODEL NO. 41120-50001 & UP MODEL NO. 41021-50001 & UP SET-UP AND PARTS LIST SKID SPRAYER Refer to the illustrated Parts List for the details of parts used in assembling the SKID SPRAYER. Note: Right and Left as used in the following instructions, refer to the operators right and left when seated in the normal operating position. Remove the Sprayer Skid from its shipping skid.
PAGE 2
6. Loosen the hose clamp on the Agitator Hose and use it to secure the Agitator Hose to the barbed elbow in the end of the Tank. (Opposite the spill-way.) 7. Place the Tank and Saddle Assembly on the Sprayer Skid. Secure it to the Skid frame with two 5/8" x 1-1/2" hex hd cap screws and hex nuts through the mounting member of the Saddle Assembly. NOTE: Note the position of the angle member of the Boom Mount Assemblies, in relation to the tube member.
PAGE 3
4. Use a torque wrench to tighten the long (1/2" x 18") wedge screws which join the Wedges to the tubes. Tighten to 50 ft. lbs. Frame tube with two (2) 1/2" x 2" clevis pins and two (2) 1/8" x 1" cotter pins. See FIG. 6. IMPORTANT! FAILURE TO TIGHTEN THE WEDGE SCREWS AT 50 FT. LBS. COULD RESULT IN THE BOOM FRAME FALLING OFF THE SPRAYER! 10. Insert the plugged end of an Extension Boom Pipe into the Pivot Assembly and secure with four (4) 1/4" x 1-1/4" cap screws and lock nuts. See FIG. 7.
PAGE 4
12. Repeat steps 10 and 11 on the opposite side to assemble the other Boom Support Assembly. 4. Connect the Overflow Hose to the Quick Coupler in the spill-way end of the Tank (FIG. 2). 13. Adjust the Booms to a level position by adjusting the jam nuts on the adjustable clevis assemblies (see FIG. 6) to the desired position, then tighten the jam nuts against the Main Frame plate.
PAGE 5
If necessary, the red and black battery wires can be pulled from the split conduit to bring them closer to your Battery. Measure very carefully, being sure to allow plenty of wire for the connections, and cut off any excess wire. 3. Crimp the ring terminals to the stripped ends of the red and black wires. Connect the red wire to the Batterys positive (+) post. Connect the black wire to the negative (-) post. 4. Connect the plugs on the 12 ft.
PAGE 6
1. 2. Sprayer Skid Spacer Tube FIG. 11 3. Transport Vehicle Bed SKID FRAME Ref Part No. Description Qty 1 92-0213 Belt Guard Assy 1 2 92-0218 Belt Shield 1 3 34-140 AMVD Hex Washer Hd Self-Tap Screw, 4 42559 Manual Storage Tube 5 42560 Storage Tube Bracket 6 20-47-AGD HHCS, 3/8 NC x 1" 7 24-11-AD Flat Washer, 3/8 8 20-50-AGD 9 92-0049 10 11 11 1/4 NC x 5/8" 6 Ref 14 Part No.
PAGE 7
PAGE 8
PAGE 9
BOOM FRAME Ref Part No. 1 42223 2 Description Qty Tube Wedge Assy Ref Part No. Description Qty 2 23* 24-18-BD Flat Washer, 1" S.A.E. 2 22-15-AJFD Lock Nut, 1/2 NC 4 24* 42196 Compression Spring 2 3 42225 1 25* 42706 Breakaway Pivot Assy 2 4 20-86-AGD HHCS, 1/2 NC x 1-1/4" 2 26* 29-199-C Spring Pin, 1/4 x 2" 2 5 42258 Spacer Tube, 1-1/4" Lg. 2 27 24-10-BD Flat Washer, 5/16 S.A.E.
PAGE 10
CENTRIFUGAL PUMP (97802) Ref Part No. Description Qty Ref Part No. Description Qty 1 27474 Volute 1 8 92-0017 Square Key, 3/16 x 1/2 Stnl. Steel 1 2 92-0018 O-Ring 1 9 27476 Frame 1 3 27484 Cap Screw, 5/16 x 1/2 Stnl. Steel 1 10 27477 Shaft, Stainless Steel 1 4 27485 Lock Washer, 5/16 Stnl. Steel 1 11 27483 Lock Ring 1 5 27487 Flat Washer, 5/16 Stnl.
PAGE 11
PUMP SYSTEM Ref Description Qty 40479 Male Quick Barb, 1" MPT 2 15 97802 Centrifugal Pump 1 41318 Dust Cap 2 16 92-0052 Red. Bushing, 1-1/4" MPT x 1" FPT 2 2 41305 Tee, 1" NPT 3 17 92-0012 Hose Barb, 1" MPT x 1" HB 2 3 41315 Hex Plug, 1" MPT 2 18 92-0240 Suction Jumper Hose, 1" I.D. x 3" 1 4 41304 Close Nipple, 1" MPT 4 19 22-12-AJD Hex Nut, 5/16" NC 2 5 41307 90° St.
PAGE 12
PAGE 13
TANK Ref Part No. Description Qty Ref Part No. Description Qty 1 42983 Hold-In Brace Assy 2 26 41800 Tank Fitting, 1" NPT - f/w Tank Assy 1 2 22-12-AJD Hex Nut, 5/16 NC 6 27 41307 90° St. Elbow, 1" NPT 2 3 24-10-BD Flat Washer, 5/16 6 28 40479 Male Quick Adapter, 1" MPT 1 4 42880 Mounting Band (Front) 2 41318 Dust Cap 1 5 92-0010 U-Bolt, 1/4 NC 4 29 92-0245 Agitator Hose, 1/2 I.D.
PAGE 14
PAGE 15
CONTROL VALVE & BOOMS Ref Part No. Description Qty Ref Part No. Description Qty 1 40480 Quick Adapter x 1" HB 2 23 41310 Red. Bushing, 3/4" MPT x 1/4" FPT 1 2 21146 Hose Clamp 4 24 92-3707 Overflow Hose, 1" ID x 100" 1 3 92-0244 Supply Hose, 1" I.D. x 80" 1 25 40493 Center Boom Pipe Assy 1 4 41730 Hose Barb, 3/4" MPT x 1" H.B. 2 26 40506 Jumper Hose, 3/4 x 19" 8 5 42939 45° St.
PAGE 16
SPRAYER CONTROL Ref Part No. Description Qty Ref Part No. Description Qty 1 42933 12-10 AWG Female Terminal 2 12 42928 96" Cable Assy (Enclos.
PAGE 17
SOLENOID VALVE (93-1027) Ref Part No. Description Qty Ref 1 92-0358 Jam Nut, Nickel Plated 1 12 2 42126 Screw - Stainless Steel 2 3 92-0359 Coil Cover, Steel Epoxy Painted 1 4 93-1029 Armature Stop, Nickel Plated 1 5 92-0361 Coil Assembly, Nylon Encapsulated 6 92-0362 Strap, Steel Epoxy Painted 7 92-0363 Part No. Description Qty Diaphragm, Viton 2 13 93-1034 Seat Washer Retainer, S.S.
PAGE 18
PAGE 19
PAGE 20
WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.