Operator's Manual

ManualsBrandsToro ManualsSprayersSkid Sprayer

The safety alert symbol means CAUTION,

WARNING, or DANGER  personal

safety instruction. Failure to comply with the

instruction may result in personal injury.

To assure maximum safety, optimum

performance, and to gain knowledge of the

product, it is essential that you or any other

operator of this equipment read and

understand the contents of this manual before

the vehicle engine is ever started. Pay

particular attention to the SAFETY

INSTRUCTIONS highlighted by this symbol

SAFETY INSTRUCTIONS

Keep these Operators Instructions and the Engine Manual in the plastic tube on the side of the Belt Guard.

It is very important that all persons operating this equipment have easy access to these instructions at all

times!

Carefully read and follow the set-up instructions that are provided with this equipment . The installation

of accessories on the TORO Skid Frame, other than those designated and sold for that express purpose

by TORO, may adversely affect the performance and safety characteristics of this equipment.

©The TORO Company - 1998

RECOGNIZE SAFETY INFORMATION

This safety-alert symbol calls attention to a dangerous situation, which could result in serious injury

or death to the operator or a bystander.

Safety, mechanical and some general information in this manual are emphasized. DANGER, WARNING

and CAUTION identify safety messages. Whenever the triangular safety symbol appears, it is followed by

a safety message that must be read and understood. For more details concerning safety, read the Safety

Instructions that follow. IMPORTANT identifies special mechanical information and NOTE identifies

general information worthy of special attention.

These instructions are provided as a guide for the safe operation and maintenance of this equipment.

However, the operators personal safety, as well as those persons in the work area, will depend on the

careful actions and good judgement of the operator.

To reduce the potential for injury or death, comply with the following safety instructions.

BEFORE OPERATING:

1. Operate this attachment only after reading

and understanding the contents of this manual. A

replacement manual is available by sending

complete model and serial number to: Hahn

Equipment Co., 1625 N. Garvin, Evansville, IN.

47711.

2. Learn how to operate the Skid Sprayer and

how to use the controls properly. DO NOT let

anyone operate this equipment without first

receiving thorough instructions.

3. Chemicals can injure persons, animals,

plants, soils or other property. To eliminate

environmental damage and personal injury:

A. Obtain proper training before using or

handling chemicals.

B. Select the proper chemical for the job.

C. Follow manufacturers instructions on

chemical container labels. Apply and handle

chemicals as recommended.

MODEL NO. 41411-30101 & UP

MODEL NO. 41020-30101 & UP

MODEL NO. 41120-30101 & UP

MODEL NO. 41021-30101 & UP

FORM NO. 99-0553

OPERATORS

INSTRUCTIONS

SKID SPRAYER

Summary of content (16 pages)

PAGE 1
FORM NO. 99-0553 MODEL NO. 41411-30101 & UP MODEL NO. 41020-30101 & UP MODEL NO. 41120-30101 & UP MODEL NO. 41021-30101 & UP OPERATORS INSTRUCTIONS SKID SPRAYER To assure maximum safety, optimum performance, and to gain knowledge of the product, it is essential that you or any other operator of this equipment read and understand the contents of this manual before the vehicle engine is ever started.
PAGE 2
SAFETY INSTRUCTIONS D. Handle and apply chemicals with care. Wear goggles and other necessary protective equipment. Handle chemicals in well ventilated areas. Never smoke while handling chemicals. E. Properly dispose of chemical container and unused chemicals. 4. To be sure of optimum performance and safety, always purchase genuine TORO replacement parts and accessories. Replacement parts and accessories made by other manufacturers could be dangerous.
PAGE 3
PRODUCT IDENTIFICATION MOD. 41411 SER. MODELNO. CH6T SPEC.NO. PS15101 SERIALNO. THE TOROCO. MINNEAPOLIS, MN. 55420 REFER TO OWNER’S MANUAL FOR OPERATION/MAINTENANCE INSTRUCTIONS AND SAFETY PRECAUATIONS. Located on the front left hand corner of the Skid Frame. KOHLER COMPANY KOHLER WISCONSIN, USA Located on the left hand engine shroud. Skid Sprayer Model No. 41410 Serial No. ____________ Kohler Engine Model No. CH6T Serial No.
PAGE 4
SAFETY AND INSTRUCTION DECALS The following decals are installed on the machine. If any become damaged or illegible, replace them. The decal part number is listed below and in your parts catalog. Replacement can be ordered from your Authorized Toro Distributor. Part No. 92-3518; Located on Belt Shield READ YOUR OPERATOR’S MANUAL FOR OPERATING AND SAFETY INSTRUCTIONS. TO GET A REPLACEMENT MANU AL, SEND MODEL AND SERIAL NUMBERS TO : THE TORO CO ., 8111 LYNDALE AVE. S., MPLS., MN 55420 65-3090 Part No.
PAGE 5
BEFORE OPERATING FILL ENGINE CRANKCASE WITH OIL: FILL FUEL TANK WITH GASOLINE: IMPORTANT! The Skid Sprayer is shipped from the factory without oil in the engines crankcase. Fuel tank capacity is approximately 3 U.S. quarts (3.18 L). 1. Position the Skid Sprayer on a level surface. 2. Clean the area around the oil fill/check plug and remove it. FIG. 1 1. Oil Fill/Check Plug 2. Fuel Tank Cap 3. Oil Drain 3. Insert a funnel into the oil fill tube and slowly pour engine oil into the crankcase.
PAGE 6
CONTROLS ELECTRIC SPRAY CONTROL SYSTEM: Controls the pressure and flow of spray solution to the Boom sections. See FIG. 3. SUCTION LINE VALVE: Opens and closes the Suction Line, which draws spray solution from the Tank to the Pump. The Valve is OPEN when the lever is positioned as shown in FIG. 2. MASTER S FU E INDUSTRIES SE 40 INC.
PAGE 7
CONTROLS IDLER ENGAGEMENT CHAIN: Used to bring the Idler Pulley into contact with the Drive Belt, creating tension to allow the engine to drive the pump . DO NOT DISENGAGE THE BELT WHILE THE ENGINE IS RUNNING! CENTRIFUGAL PUMP SYSTEM SET-UP: 5. Start the Skid Sprayers engine. 6. Turn ON the Master Boom Switch and all three individual Boom Switches. 7. Set the Pressure Gauge to the desired operating pressure. 1. Install the Drive Belt on the Engine and Pump Pulleys as shown in FIG. 4. 1.
PAGE 8
OPERATING INSTRUCTIONS BEFORE STARTING THE ENGINE TO BEGIN THE DAYS SPRAYER APPLICATION: STOPPING THE ENGINE: 1. 2. 3. 4. 2. Close the fuel shut-off valve. See FIG. 6. Check the engine crankcase oil. Check the Air Cleaner. Check cooling air intake areas. Check the fuel tank. 1. Move the throttle control to the off position. TAKE MACHINE TO WORK SITE: 1. Pull the Idler Engagement Chain to bring the Idler Pulley into contact with the Drive Belt.
PAGE 9
MAINTENANCE MAINTENANCE SCHEDULE These required maintenance procedures should be performed at the frequency stated in the table. They should also be included as part of any seasonal tune-up. FREQUENCY MAINTENANCE REQUIRED Daily or Before Starting Engine Fill fuel tank. Check oil level. Check air cleaner for dirty¹, loose, or damaged parts. Check air intake and cooling areas, clean as necessary¹. Every 25 Hours Service precleaner element¹. Every 100 Hours Service air cleaner element¹.
PAGE 10
MAINTENANCE WARNING SUCTION LINE STRAINER: Before servicing or making adjustments to the Skid Sprayer, stop the transport vehicle and set the parking brake. Shut off the Skid Sprayer engine. Pull wire off the spark plug to prevent the engine from being started. AFTER THE INITIAL RUN-IN (APPROXIMATELY 5 HOURS): After every 50 hours of operation, or daily if spraying wettable powders: 1. Turn off the Suction Line Valve, if the Tank has been filled. 2.
PAGE 11
MAINTENANCE SERVICE PRECLEANER AND AIR CLEANER: Check the Air Cleaner daily or before starting the engine. Check for and correct heavy buildup of dirt and debris, as well as loose or damaged components. Service Precleaner: Wash and re-oil the precleaner after every 25 hours of operation (more often under dusty or dirty conditions). 1. Loosen air cleaner cover retaining knob. NOTE: Choke control must be in the OFF position. 2.
PAGE 12
CHECK SPARK PLUG: Every 100 hours of operation, clean the area around the base of the plug and check its condition. Reset the gap to 0.030in. (0.76mm) or replace with a new plug as necessary (see FIG. 10). Use a Champion type RC12YC or equivalent. Torque to 18-22 ft. lbs. (24.4 - 29.8 Nm). 0.76mm (0.030in.) Gap 1. Wire Gauge 2. Spark Plug 12 FIG. 10 3.
PAGE 13
PAGE 14
PAGE 15
PAGE 16
The Toro Promise A Two Year Limited Warranty The Toro Company promises to repair your Model 41021 Skid Sprayer if defective in materials or workmanship. The following time periods from the date of purchase apply special warranty terms, on certain components, may be offered through The Toro Company by the component manufacturers: Commercial Products...........................2 Years The cost of parts, labor and transportation are included.