41530 MODEL NOQ. 41520, 41521, 41020, 41021, 41038 and FORM NO. 42953 SET-UP AND PARTS LIST PRO-CONTROL SPRAY SYSTEM ; FOR USE ON THE MULTI-PRO 5200 VEHICLE Refer to the illustrated Parts List for the details of parts used in assembling the Sprayer System. “Right* and “Left” as used in the following instructions, refer to the operator’s right and left when seated in the normal operating position. Likewise, “Front* and "Rear" as seen from the operator’'s posit sen.
TANK ASSEMBLY: Cut the shipping straps and remove the Spray Tank and Saddle Assembly from the skid. apply thread sealer and install the 90° barbed elbow into the bottom of the Tank. NOTE: Position the barbed elbow as shown in FIG. 2, so that when the Suction Hose is attached, it will angle toward the left front of the Vehicle after the Tank is.installed.on the Vehicle. ® Attach the 1" x 35° Suction Hose to the pared elbow with a hose clamp.
BOOM ASSEMBLY: Use a paint Rush to apply. a heavy coating of grease to the tubes which are to be inserted into the Vehicle Frame. ® Install the two Boom Mount Assembly into the Vehicle Frame as shown in FIG. 4. Use a tongue wrench to tighten the long {1/4" x 8%) screws which join the Wedges to the tubes. Tighten to 50 ft. 1bs. CAUTION! FAILURE TO TIGHTEN THESE SCREWS SECURELY COULD RESULT IN THE BOOM FRAME FALLING OFF THE VESICLE! THESE INSTRUCTIONS APPLY TO THE ASSEMBLY OF THE MANUAL, BOOM ONLY.
% Insert an Extension Boom Pipe into the pivot Assembly and secure with four 174" x hex hd cap screws and lock nuts, See FIG. 6. Repeat on the opposite side to assemble the other Extension Boom. = Attach the Boom Support Assembly to the pivot Assembly, using a S/16" x . screw and hex nut. See FIG. 6. Secure the two plates of the Boom Support Assembly to the Extension Boom Pipe, using two U-bolts and four lock nuts. ® Assemble the Boom Support Assembly to the other Extension Boom Pipe.
LOW METER: Attach the Adapter Hose and the male Wiki-Coupler to the rear bath on the Flow Meter. (connect the Supply Hose to the front barb on the Flow Meter. B Secure the complete Flow Meter Assam bly to the Mounting Bracket with the WO large hose clamps. W Attach the Mounting Bracket to the left rear Fender as shewn in FIG.
TANK REF PART NO. DESCRIPTION QrY 1 42983 Hold~In Brace ASHY ...everyone. 2 2 22-12-TAD Hex Nut, 5/16 NC & 3 24-10-8 Flat Washer, 5/16 4 4 43007 Mounting Band (front) 2 5 5125 U-Bolt, 1/4 NC 4 6 42158 Rubber Hold Down Strap . 2 7 42259 Boom Hold-In Says. 41809 Mounting Band Bolt a8 9 25-25-GAD Carriage Bolt, 5/16 NC & 10 22-11-AD Hex Nut, 1/4 Nc cavers 8 11 42316 Boom He old-In Ass: R.H. T 12 42218 Counting Band .. caesura 2 13 42277 Pressure Gage Bracket Says .
HYDRAULIC SPRAY PUMP REF PART NO. DESCRIPTION QTY 1 41790 Hydraulic Wiki Couplet (Male) ...ousveicsvionnins 2 2 42847 Hydraulic Hose Assembly meatloaves PRI 2 3 41307 gD st. Elbow, 1" NPT .. 1 4 41304 Close Nipple, 1% NPT 2 5 41305 Tee, 1" NPT ,...volcanoes 2 6 41306 Reducer Bushing 1" x 1/2 KPT 1 7 41314 Close Nipple, 1/2 NPT PR 1 8 40192 Ball valve, 1/2 NPT (agitator) ..
MOTORIZED CONTROL VALVE & BOOMS REF PART NO. DESCRIPTION QrY 1 40485 Pressure Gage Underappreciated 1 2 42277 Gage Mounting Bracket centavo 1 3 41292 80 Elbow, 1/4 MPT x 3/8 Barb 1 4 96609 Hose Clamp, 3/8 Hose severance 2 5 42276 Bose (Pressure Gage) 26393 Hose Clamp, #48 ..ic.vcunnann Andean ERE PRY 1 7 40480 Wiki Couplet, 1" Bard ...decisiveness .a 1 8 21146 Hose Clamp, 1" HOVE vvvevavonnrrvvoaune PN 2 9 41328 Flow Meter Hose, 1" x 36" 1 10 41730 Hose Barb, 3/4 MPT x 1" Barb 1 i1 42939 45 St.
SPEED SENSOR REP PART NO. DESCRIPTION QY 1 Hex Nut, 1/2 NC 8 2 Magnet Says. (Red) 2 Magnet Easy. (Black) 2 3 Sensor Switch Ayes 1 4 Sensor Rod . seen b 5 Turret SAYS 2 6 Lock Washer, 1/4 caravans 4 7 Hex Nut, 174 NC 6 8 HES, occupants 2 CONTROL CONSOLE REF PART NO. DESCRIPTION QY 1 42722 POWER Switch 1 2 42723 Rate 1/Rate 2 Manual Switch . 1 3 42724 MAN ADJ S Witch ciwawrsveons 1 4 42558 BOOM Switch nervelessness 3 5 42725 MISTER Switch 1 42718 Luge Holder ...vevevovve 1 & 41472 Control Console .
REF PART NC. DESCRIPTION 1 42084 Drain/Vent Plug 2 42085 Pump Casing 3 42086 Impeller Nut 4 42087 Impeller 8 42088 Mechanical Seal (Vito) & 42089 "0~ Ring 7 20-4T-RGD HHS, 42090 Mounting Flange 9 42091 Name Plate — Model 9303C-EMI 11 42092 Singer Rin 12 42093 Retaining Ring 13 42024 Snap Rin 14 42095 Ball Bearing 15 42096 Spacer 18 42097 Shaft Seal 17 42098 Seal Spacer 18 42099 Thrust Bearing Say. (Incl.