Installation Instructions

ManualsBrandsToro ManualsAttachmentsSpray Gun Kit, Multi-Pro 5600 Turf Sprayer

FormNo.3365-364RevA

SprayGunKit

Multi-Pro

5600/5700TurfSprayer

ModelNo.41580—SerialNo.310000001andUp

InstallationInstructions

Readthismanualcarefullytolearnhowtooperateand

maintainyourproductproperly.Theinformationin

thismanualcanhelpyouandothersavoidinjuryand

productdamage.AlthoughTorodesignsandproduces

safeproducts,youareresponsibleforoperatingthe

productproperlyandsafely.

YoumaycontactTorodirectlyatwww .Toro.comfor

productandaccessoryinformation,helpndinga

dealer,ortoregisteryourproduct.

Wheneveryouneedservice,genuineToroparts,or

additionalinformation,contactanAuthorizedService

DealerorToroCustomerServiceandhavethemodel

andserialnumbersofyourproductready.

Figure1

illustratesthelocationofthemodelandserialnumbers

ontheproduct.

Figure1

1.Modelandserialnumberplate

ModelNo.

SerialNo.

Safety

Thismanualidentiespotentialhazardsandhas

safetymessagesidentiedbythesafetyalertsymbol

(Figure2),whichsignalsahazardthatmaycauseserious

injuryordeathifyoudonotfollowtherecommended

precautions.

Figure2

1.Safetyalertsymbol

Thismanualuses2otherwordstohighlightinformation.

Importantcallsattentiontospecialmechanical

informationandNoteemphasizesgeneralinformation

worthyofspecialattention.

Readalsothesafetyandoperationinstructionsinthe

vehicleOperator’sManual.

•Donotaimthehandsprayeratanypersonoranimal.

Fluidsunderhighpressurecanpenetrateskinand

causesevereinjury,possiblyresultinginamputation

ordeath.Hotliquidsandchemicalscanalsocause

burnsorinjury.Ifanypartofthebodycomesin

contactwiththespraystream,immediatelyconsulta

physicianfamiliarwithinjecteduidinjuries.

•Donotplaceyourhandoranyotherpartofyou

bodyinfrontofthespraynozzle.

•Donotleavetheequipmentunderpressurewhen

youarenotpresent.

•Donotusethehandsprayerifthehose,triggerlock,

nozzle,oranyotherpartisdamagedormissing.

•Donotusethehandsprayerifthereareanyleaksin

anyhoses,ttings,orothercomponents.

•Donotspraynearpowerlines;thespraystream

couldcontactthepowerlinesandgiveyoua

potentiallyfatalelectricalshock.

•Donotdrivewhilesprayingwithahandsprayer.

•Wearrubbergloves,safetygoggles,andafullbody

protectivesuitwhensprayingchemicalswiththe

handsprayer.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (16 pages)

PAGE 1
Form No. 3365-364 Rev A Spray Gun Kit Multi-Pro® 5600/5700 Turf Sprayer Model No. 41580—Serial No. 310000001 and Up Installation Instructions Read this manual carefully to learn how to operate and maintain your product properly. The information in this manual can help you and others avoid injury and product damage. Although Toro designs and produces safe products, you are responsible for operating the product properly and safely. You may contact Toro directly at www.Toro.
PAGE 2
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 106-5211 1. Boom spray 2. Hand spray 3. Continuous variable setting 4. Increase 5.
PAGE 3
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 Description Use Qty.
PAGE 4
1 2 Preparing the Machine Installing the Hose Hooks No Parts Required Parts needed for this procedure: Procedure 2 Hose hook 2 Carriage bolt (5/16 x 3/4 inch) 2 Washer (3/8 inch) 2 Flange nut (5/16 inch) 1. Ensure that the machine is empty of all fluids. If chemicals have been used in the machine, flush the system thoroughly with clean water then drain the water; refer to your vehicle Operator’s Manual for instructions. Procedure 2. Disconnect the negative battery terminal from the battery.
PAGE 5
Figure 5 1. Rear tank strap 2. Hose hook 3. Carriage bolt (5/16 x 3/4 inch) 4. Washer (3/8 inch) 5. Flange nut (5/16 inch) Figure 6 1. Boom supply valves 2. Boom supply hose 4. Secure the tank strap using the fasteners you removed previously. 2. Cut the boom supply hose 8-3/4 inches (22 cm) to the right of the flow meter (if equipped) or 32 inches (81 cm) from the supply tee (located directly behind the boom valves) using a hacksaw (Figure 6).
PAGE 6
. Cut the by-pass hose half way between the boom valves and the tank (Figure 8). 1 2 G013325 3 5 4 Figure 9 1. Boom valve assembly 2. Fly-nut 3. Boom supply hose 4. Retaining fork 5. Lower tee Figure 8 1. By-pass hose 2. Agitation hose 2. Loosen the hose clamp that secures the agitation hose to the 90 degree fitting on the agitation valve and remove the hose. Remove the retaining fork securing the other end of the hose to the tee. Discard agitation hose assembly.
PAGE 7
2 3 1 G013327 2 2 4 4 1 3 Figure 11 1. S67 straight fitting 3. Retaining fork, removed previously 4. S67 90 degree fitting 2. Lower tee G013373 4. Remove the S67 straight barbed fitting and retaining fork from the hose reel control valve assembly (Figure 12). Slide a hose clamp onto hose. Apply liquid soap to hose and fitting. Slide hose end all the way onto fitting. Secure with hose clamp. Connect S67 end to control valve and secure with retainer. Figure 13 1. By-pass hose 2. Agitation hose 3.
PAGE 8
4. Apply a liberal amount of liquid soap to the barb of the fitting and to the inside of the hose coming from the flow meter. 5. Slide a large hose clamp over the hose and install the fitting all the way into the hose, securing it with the hose clamp. 7. Remove retainer and disconnect flow meter supply hose at tee fitting. Cut the hose 32 inches (81 cm) to the left of flow meter (Figure 14). Discard the hose end not attached to flow meter. 8.
PAGE 9
Slide hose all the way onto fitting. Secure with hose clamp. 13. Slide hose clamp onto hose. Apply liquid soap to hose and 90 deg barbed fitting on agitation valve. Slide hose all the way onto barbed fitting. Secure with hose clamp. 4 Figure 18 1. Hose from the flow meter or supply tee 2.
PAGE 10
Figure 21 Boom frame 1. Boom frame 2. Boom frame bolts Figure 20 1. Control valve 2. Spacer 5. Install the short hose assembly to the bottom of the control valve and to the boom supply valves, securing it with one previously used retainer and one new retainer (Figure 22). 3. Flange head bolts (5/16 x 3 inches), washers (3/8 inch), and flange nuts (5/16 inch) 4. Bottom opening of the control valve.
PAGE 11
bolts (5/16 x 3 inches), two washers (3/8 inch) and two flange nuts(5/16 inch). Figure 23 1. Female-threaded end of the short hose assembly 2. Fitting on the side of the control valve 8. Connect the other end of the long hose assembly to the open fitting on the S53 tee that you installed into the by-pass hose (Figure 23) and secure it with a small retainer. Figure 25 1. Control valve For Model Year 2010 and Newer For model year 2009 and older refer to the previous procedure. 1.
PAGE 12
Figure 28 1. Female-threaded end of the short hose assembly Figure 26 Boom frame 1. Boom frame 2. Boom frame bolts 10. Connect the other end of the long hose assembly to the open fitting on the S53 tee that you installed into the by-pass hose (Figure 28) and secure it with a small retainer. 5. Install S67 straight fitting into the bottom of the control valve and secure with a retainer. 2 G013394 5 3 1 2.
PAGE 13
6. Push the other end of the red tube into the fitting on the back of the control valve. 7. Install the red handle on the face of the control valve assembly and secure it with the screw as shown in Figure 31. Note: Ensure that you install the handle in the orientation shown in Figure 31. Figure 29 1. Pressure gauge 2. Bracket (inside of the control box cover) 3. Nut 4. Reducer fitting 5. Black plastic fitting 2. Install the black plastic fitting into the reducer fitting on the gauge (Figure 29).
PAGE 14
Figure 32 1. Control valve 2. Hose 2. Wrap the hose around the hooks on the tank and secure the gun as shown in Figure 33. Figure 33 3. Ensure that the control valve assembly and the tank are about 1 inch apart. If they are not, adjust the boom frame.
PAGE 15
Operation is desired. Contact your Authorized Toro Dealer to obtain a Toro Heat Shield Blanket kit, for turf sprayers. WARNING Switching from Boom Spray Mode to Hand Spray Mode Fluid under pressure can penetrate skin and cause injury. • Keep your body and hands away from nozzles that eject high pressure fluid. • Do not aim the sprayer at any person or animal. • Make sure all fluid hoses and lines are in good condition and all connections and fittings are tight before applying pressure to the system.
PAGE 16
Spraying with the Hand Sprayer 1. Unwind the hose from the hooks. 2. Release the trigger lock. 3. Direct the spray gun nozzle at the area to be sprayed and pull the trigger. 4. Release the trigger and set the trigger lock when finished. Switching from Hand Spray Mode to Boom Spray Mode Figure 36 1. Press the rate control switch to reduce the pressure and stop the pump. 2. Turn the pump and agitation switch to the Off position if desired. 3.