Installation Instructions

ManualsBrandsToro ManualsAttachmentsSpray Gun Kit, Multi-Pro 5600 Turf Sprayer

W 2004 by The Toro Company

8111 Lyndale Avenue South

Bloomington, MN 55420-1196

Printed in the USA

Spray Gun Kit

for Multi-Pro

)

5600/5700 Sprayers

Model No. 41580—Serial No. 240000001 and Up

Form No. 3352-402 Rev B

Installation Instructions

Installation

Note: Determine the left and right sides of the machine from the normal operating position.

Note: You will need to purchase Teflon tape before installing this kit.

Description

Qty. Use

Hose hook

Carriage bolt, 5/16 x 3/4 inch

Washer, 3/8 inch

Flange nut, 5/16 inch

Install the hose hooks

Barbed hose fitting, large

S67 female/female fitting

Control valve assembly

Spacer

Flange-head bolt, 5/16 x 3 inches

Washer, 3/8 inch

Flange nut, 5/16 inch

Hose assembly, long

S53 tee

S53 tee fitting

Hose assembly, short

O-ring

Retainer, large

Retainer, small

Hose clamp, large (1 inch)

Install the control valve.

Pressure gauge

Reducer fitting and nut

Plastic fitting, small

Control box cover

Flange-head bolt, 1/4 x 3/8 inch

Control handle

Screw

Red tubing

Install the switches, gauge, and cover

Hose and spray gun assembly 1 Connect the spray hose

Summary of content (8 pages)

PAGE 1
Form No. 3352-402 Rev B Spray Gun Kit for Multi-Pro) 5600/5700 Sprayers Model No. 41580—Serial No. 240000001 and Up Installation Instructions Installation Note: Determine the left and right sides of the machine from the normal operating position. Note: You will need to purchase Teflon tape before installing this kit. Description Qty.
PAGE 2
Preparing the Machine 3. Install the upper hose hook as shown in Figure 2, using a carriage bolt (5/16 x 3/4 inch), a washer (3/8 inch), and a flange nut (5/16 inch). Note: When installing this kit on a machine with a Rinse kit, refer to the Rinse Kit Installation Instructions for special instructions to accommodate this installation. 2 5 4 1. If chemicals have been used in the machine, flush the system thoroughly with clean water; refer to your vehicle Operator’s Manual for instructions.
PAGE 3
Tapping into the Machine Hoses 4 1. Remove the retainer securing the end of the boom supply hose connected to the tee located to the right of the boom supply valves and disconnect it (Fig. 4). 1 8 inches (20 cm) 4 3 2 m–6375 2 1 Figure 5 1. Hose 2. Ratcheting hose clamp 3. Fitting 4. Flow divider 5. Cut the by-pass hose half way between the boom valves and the tank (Fig. 6). 3 m–6356 3 Figure 4 1. Boom supply valves 2. Boom supply hose 2 3. Disconnect here 4. Flow meter 2 2.
PAGE 4
Installing the Control Valve Note: If there is not enough clearance between the control valve and the tank, loosen the 2 bolts securing the boom frame to the vehicle and back the boom frame out until there is at least 3 inches of clearance between the control valve and the tank (Fig. 9). 1. Look in the opening under the control valve and ensure that the opening in the white ball valve is open toward the bottom (Fig. 8).
PAGE 5
7. Insert the O-ring into the female threaded end of the long hose assembly and install it onto the fitting on the side of the control valve (Fig. 11). 4. Install the cover on the control valve assembly (Fig.13 ), securing it with 3 bolts. 2 2 1 2 1 2 m-7815 Figure 13 Figure 11 1. Female-threaded end of the short hose assembly 1. Control valve cover 2. Fitting on the side of the control valve 5. Push the end of the small red tube into the fitting on the bottom of the pressure gauge. 8.
PAGE 6
Connecting the Spray Hose 3. Ensure that the control valve assembly and the tank are about 1 inch apart. If they are not, adjust the boom frame (Fig. 9). 1. Thread and tighten the nut on the end of the hose and spray gun assembly to the threaded male fitting on the control valve assembly (Fig. 15). Safety Instructions 1 2 Improper use or maintenance by the operator or owner can result in injury.
PAGE 7
Safety and Instruction Decals Switching from Boom Spray Mode to Hand Spray Mode Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 1. Stop the machine and set the parking brake. Warning Driving while using the hand sprayer can cause loss of control, resulting in injury or death. Do not operate the hand sprayer while driving. 2.
PAGE 8
Spraying with the Hand Sprayer 1. Unwind the hose from the hooks. 2. Release the trigger lock. 3. Direct the spray gun nozzle at the area to be sprayed and pull the trigger. 4. Release the trigger and set the trigger lock when finished. Switching from Hand Spray Mode to Boom Spray Mode 1. Press the rate control switch to reduce the pressure and stop the pump. 2. Move the control handle counter-clockwise, pointing rearward (Fig. 18). Figure 19 1 Figure 18 1. Control handle 3.