Operator's Manual

ManualsBrandsToro ManualsAttachmentsCovered Boom Kit, Multi-Pro 5700/5800 Turf Sprayer with Truss-Style Boom

FormNo.3406-554RevA

CoveredBoomKit

MultiPro

TurfSprayerwithTruss-StyleBoom

ModelNo.41602—SerialNo.316000001andUp

InstallationInstructions

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Preparethemachine.

11-nozzle,center-boomcover1

Rubbercover1

Reinforcementplate

Poprivet(3/16x1/2inch)

Washer(3/16inch)

Preparethecenter-boomcover(foran

11-nozzleassembly).

12-nozzle,center-boomcover1

Poprivet(3/16x1/2inch)

Washer(3/16inch)

Rubbercover1

Reinforcementplate

Attachan11-nozzleboomcovertoa

12-nozzleboomcover.

Center-boombracket(2014andearlier

models)

Boom-mountplate2

U-nut8

Hex-headbolt(3/8x1-1/4inch)

Model/serialnumberdecal

Regulatorydecal(119-4986)

Flangenut(3/8inch)

Washerplate4

Hex-headbolt(5/16x1-1/4inch)

Center-boombracket(2015andlater

models)

Installthecenter-boombracketsand

cover.

Wing-boomcover2

Washerplate16

U-nut12

Hex-headbolt(5/16x1-1/4inch)

Installthewing-boomcovers.

Drain-valve-mountbracket1

Carriagescrew(5/16x1-1/4inch)

Flangenut(5/16inch)

Installthedrain-valve-mountbracket.

Flangenut(5/16inch)

Flange-headbolts(5/16x1inch)

Movethedrainvalve.

Nopartsrequired

–

Ensurethattheboomcovershave

properclearance.

Important:Useair-induction,at-fannozzleswiththecoveredboomkittoavoidchemicalbuilduponthecovers

duringapplication.RefertotheToronozzlechartfordetails.

Note:InstalltheSpringUpgradeKit(PartNumber120-8508)withthecoveredboom.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3406-554*A

Summary of content (12 pages)

PAGE 1
Form No. 3406-554 Rev A Covered Boom Kit Multi Pro® Turf Sprayer with Truss-Style Boom Model No. 41602—Serial No. 316000001 and Up Installation Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 7 8 Description Use Qty.
PAGE 2
1 2 Preparing the Machine Preparing the Center-Boom Cover (for an 11-Nozzle Assembly) No Parts Required Procedure Parts needed for this procedure: CAUTION If you leave the key in the ignition switch, someone could accidently start the engine and seriously injure you or other bystanders. Remove the key from the ignition switch before you install the kit. 1 11-nozzle, center-boom cover 1 Rubber cover 1 Reinforcement plate 11 Pop rivet (3/16 x 1/2 inch) 11 Washer (3/16 inch) Procedure 1.
PAGE 3
2. Align the holes on the reinforcement plate with the holes on the rubber cover (Figure 3). 3 Attaching an 11-Nozzle Boom Cover to a 12-Nozzle Boom Cover Parts needed for this procedure: Figure 3 2. Rubber cover 1. Reinforcement plate 3. Install 11 pop rivets (3/16 x 1/2 inch) and washers (3/16 inch) to the center-boom cover (Figure 4). 1 12-nozzle, center-boom cover 22 Pop rivet (3/16 x 1/2 inch) 22 Washer (3/16 inch) 1 Rubber cover 1 Reinforcement plate Procedure 1.
PAGE 4
2. Install 11 pop rivets (3/16 x 1/2 inch) and washers (3/16 inch) to the reinforcement plate, attaching 11-nozzle cover to the 12-nozzle cover (Figure 6). 4 Installing the Center-Boom Brackets and Cover Parts needed for this procedure: Figure 6 1. 11-nozzle cover 3. Pop rivet (3/16 x 1/2 inch) and washer (3/16 inch) 2. Reinforcement plate 4. 12-nozzle cover 3.
PAGE 5
6 6 1 Installing the Drain-Valve-Mount Bracket 2 Parts needed for this procedure: 7 3 4 5 1 Drain-valve-mount bracket 2 Carriage screw (5/16 x 1-1/4 inch) 3 Flange nut (5/16 inch) g0302 99 Procedure Figure 8 2015 and later models 1. Flange nut (3/8 inch) 5. Hex-head bolt (5/16 x 1-1/4 inch) 2. Bracket 3. Center-boom cover 6. U-nut 7. Flange bolt (3/8 inch) 1.
PAGE 6
7 Moving the Drain Valve Parts needed for this procedure: 2 Flange nut (5/16 inch) 2 Flange-head bolts (5/16 x 1 inch) Procedure 1. Remove the lynch pin that secures the drain valve to the sprayer-pump bracket (Figure 11). Figure 10 1. Flange locknut (5/16 inch) 3. Drain-valve bracket 2. Fender strap 4. Carriage bolt (5/16 x 1-1/4 inches) 3. Assemble the valve bracket, fender strap, mud flap, and fender (Figure 10) with the 2 carriage bolts (5/16 x 1-1/4 inches) and 2 flange locknuts (5/16 inch).
PAGE 7
3. Remove the 2 mounting pegs from the drain valve (A of Figure 12). Figure 12 1. Mounting peg 3. Flange-head bolts (5/16 x 1 inch) 2. Drain valve 4. Flange locknuts (5/16 inch) Figure 13 7. Move the drain valve outboard and down to secure the valve to the bracket (B and C of Figure 13). 4. Thread the 2 flange locknuts (5/16 inch) onto the 2 flange-head bolts (5/16 x 1 inch) as shown in (B and C of Figure 12) 8 5.
PAGE 8
Figure 14 2014 models and older 1. Washer plate (18) 6. Flange nut—3/8 inch (8) 11. Center-boom cover 2. Spray nozzle (properly oriented) 7. U-nut (16) 12. Wing-boom cover (2) 3. Truss frame (outer-boom section) 8. Center-boom bracket (4) 13. Hex-head bolt—5/16 x 1-1/4 inches (16) 4. Hex-head bolt—3/8 x 1-1/4 inches (8) 5. Boom-mount plate (2) 9. Regulatory decal 10.
PAGE 9
Notes:
PAGE 10
Notes:
PAGE 11
European Privacy Notice The Information Toro Collects Toro Warranty Company (Toro) respects your privacy. In order to process your warranty claim and contact you in the event of a product recall, we ask you to share certain personal information with us, either directly or through your local Toro company or dealer. The Toro warranty system is hosted on servers located within the United States where privacy law may not provide the same protection as applies in your country.
PAGE 12
The Toro Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).