Operator's Manual

ManualsBrandsToro ManualsAttachmentsRoad Light and Homologation Kit, Multi-Pro 5800 Turf Sprayer

FormNo.3370-141RevA

RoadLightandHomologationKit

Multi-Pro

5800TurfSprayer

ModelNo.41603

OperatorManual

Installation

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Mainbeamlight2

Wireharnessheadlightadapter2

Installthemainbeamlights.

Positionlight2

Hex-headangenut(3/8inch)

U-bolt4

Signalindicatorplate

Installthepositionlights.

Flatwasher2

Hexnut(#6-32)

Locknut(#6)

Phillipspan-headscrew(#6x2–1/2

inches)

Turnsignalcontroller1

Turnsignalcontrollermountingbracket1

Installthesignalcontroller.

Brakelightswitch1

Brakelightswitchbracket1

Installthebrakelightswitch.

Flashermodule1

Hexangenut(1/4inch)

Hex-headangescrew(1/4x3/4inch)

Installtheashermodule.

Rockerswitch1Installtherockerswitch.

Taillight2

Hex-headangescrew(5/16x3/4inch)

Flangenut(5/16inch)

Left-handsignalbracket

Right-handsignalbracket1

Installthetaillights.

Cabletie

Wireharnesskit1

Installthewireharness.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3370-141 Rev A Road Light and Homologation Kit Multi-Pro® 5800 Turf Sprayer Model No. 41603 Operator Manual Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty.
PAGE 2
1 Installing the Main Beam Lights Parts needed for this procedure: 2 Main beam light 2 Wire harness headlight adapter Procedure 1. Move the sprayer onto a level surface, set the parking brake, stop the pump, stop the engine, and remove the ignition key. 2. Remove the retainers that secure the headlights to the hood and remove the headlights. 3. Insert the new main beam lights (Figure 1), and secure them with the retainers that you removed in step 2. Figure 1 1. 2. 3. 4. 5. 6.
PAGE 3
2 Installing the Position Lights Parts needed for this procedure: 2 Position light 8 Hex-head flange nut (3/8 inch) 4 U-bolt 2 Signal indicator plate Procedure Figure 2 Install a position light onto each side of the rollover bar 58 inches (147 centimeters) from the ground to the top of the bracket as shown in Figure 1. 1. Turn signal controller 2. Phillips pan-head screws 3. Hex nuts 4. Bolts (existing) Note: Ensure that the amber lens on each light faces forward and on the bottom. 5.
PAGE 4
6 Installing the Rocker Switch Parts needed for this procedure: 1 Figure 3 1. Brake light switch Rocker switch 2. Brake light switch bracket Procedure 1. Remove the plug from one of the unused holes in the dashboard. 3. Install the brake light switch to the bracket with 2 screws, 2 washers, and 2 hex nuts on the machine (Figure 3). 2. Insert the rocker switch (Figure 4). 4. Adjust the bracket so that the brake switch opens when you press down on the brake pedal 1/4 inch (6 mm).
PAGE 5
7 Installing the Tail Lights Parts needed for this procedure: 2 Tail light 4 Hex-head flange screw (5/16 x 3/4 inch) 4 Flange nut (5/16 inch) 1 Left-hand signal bracket 1 Right-hand signal bracket Procedure 1. Install the left-hand and right-hand signal brackets to the boom support with 4 hex-head flange screws and 4 hex flange nuts (Figure 5). Figure 5 1. Hex-head flange screw 2. Flange nut 3. Tail light 4. Left-hand signal bracket 5.
PAGE 6
Figure 6 1. 3/4 inch (19 mm) 2. Drill 2 holes (5/16 inch (8 mm) diameter) here 3. 2-1/4 inches (57 mm) 4. 2 inches (51 mm) 2. Install the tail lights onto the signal brackets (Figure 5). Note: Position the amber lens of each tail light to the outside. • main switch 8 • tail lights 4. Locate the kit connector on the main wire harness behind the dashboard, and connect the kit wire harness connector to the power connector on the main wire harness.
PAGE 7
Schematics (Rev.
PAGE 8