Installation Instructions

ManualsBrandsToro ManualsAttachmentsHand Spray Gun Kit, 2014 and Before Multi-Pro 5800 Turf Sprayer

FormNo.3366-887RevA

HandSprayGunKit

Multi-Pro

5800TurfSprayer

ModelNo.41605—SerialNo.311000001andUp

InstallationInstructions

Thehandspraygunkitisanattachmentforaturf

sprayapplicationvehicleandisintendedtobeusedby

professional,hiredoperatorsincommercialapplications.

Itisprimarilydesignedforsprayingonwell-maintained

lawnsinparks,golfcourses,sportselds,andon

commercialgrounds.

ThisproductcomplieswithallrelevantEuropean

directives.Fordetails,pleaseseetheseparate

product-specicDeclarationofConformity(DOC)

sheet.

Readthismanualcarefullytolearnhowtooperateand

maintainyourproductproperly.Theinformationin

thismanualcanhelpyouandothersavoidinjuryand

productdamage.AlthoughTorodesignsandproduces

safeproducts,youareresponsibleforoperatingthe

productproperlyandsafely.

YoumaycontactTorodirectlyatwww .Toro.comfor

productandaccessoryinformation,helpndinga

dealer,ortoregisteryourproduct.

Wheneveryouneedservice,genuineToroparts,or

additionalinformation,contactanAuthorizedService

DealerorToroCustomerServiceandhavethemodel

andserialnumbersofyourproductready.

Figure1

illustratesthelocationofthemodelandserialnumbers

ontheproduct.

Figure1

1.Modelandserialnumberplate

ModelNo.

SerialNo.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

Summary of content (12 pages)

PAGE 1
Form No. 3366-887 Rev A Hand Spray Gun Kit Multi-Pro® 5800 Turf Sprayer Model No. 41605—Serial No. 311000001 and Up Installation Instructions The hand spray gun kit is an attachment for a turf spray application vehicle and is intended to be used by professional, hired operators in commercial applications. It is primarily designed for spraying on well-maintained lawns in parks, golf courses, sports fields, and on commercial grounds.
PAGE 2
Safety This manual identifies potential hazards and has safety messages identified by the safety alert symbol (Figure 2), which signals a hazard that may cause serious injury or death if you do not follow the recommended precautions. • • • Figure 2 • 1. Safety alert symbol • This manual uses 2 other words to highlight information. Important calls attention to special mechanical information and Note emphasizes general information worthy of special attention.
PAGE 3
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 Description Use Qty. No parts required – Hose hook Washer (3/8 inch) Locknut (5/16 inch) Carriage bolt Manual valve assembly Threaded rod Locknut Washer Jam nut Control box and bracket assembly Bolt (1/4 x 5/8 inch) Locknut (1/4 inch) Hose Hose clamp Long hose with fitting Spray gun Hose clamp, small 2 2 2 2 1 4 8 6 8 1 3 3 1 2 1 1 1 Prepare the machine. Installing the hose hooks.
PAGE 4
Figure 4 1. Agitation valve 2. Left-hand mount bracket 4. Right-hand mount bracket 5. Fasteners ( loosen but do not remove) 3. Bypass valve assembly Figure 3 1. Tank strap fasteners (older 5. Washer (3/8 inch) style) 2. Front tank strap 6. Locknut (5/16 inch) 3. Hose hook (2) 7. Tank strap fasteners (newer style) 4. Carriage bolt (5/16 x 3/4 inch) (2) 2. Remove the long bolts and fasteners that secure the valve assembly (Figure 5). Note: Discard the long bolts, but retain the washers and locknuts.
PAGE 5
. Move the right-hand mount bracket away from the existing valve assembly. 6. If the existing O-ring is not seated in the open end of the boom valve body, install it now. 7. Install the adapter that you removed in step 4. 8. Insert the threaded rods through the holes in the valve bodies of the boom bypass valves, and for the 2 rods closest to the mounting rail, through the left-hand mount bracket (Figure 4 and Figure 6). Figure 7 1. Reducing adapter 2. Threaded rod end (the rest not shown) 3. Washer 4.
PAGE 6
2 19. Secure the bolts of the right-hand mount bracket to the mounting rail. 3 4 20. If the tee fitting is not connected to the elbow cap, install the tee fitting. 1 Note: Position the tee fitting so that the side port faces the tank. A. Remove the reducer fitting that secures the red pressure gauge tube to the elbow adapter. B. Install the reducer fitting that you removed in the previous step to the top port the tee fitting. C. Install the red pressure gauge. 4 G014223 Figure 8 1. Bolt (3) 2.
PAGE 7
5 Installing the Supply Hose Parts needed for this procedure: 1 Hose 2 Hose clamp Figure 11 Procedure 1. Slide a hose clamp over the open end of the hose and install the hose over the exposed barb in the manual valve. 2. Secure the end of the hose with a small hose clamp. 3. Wrap the hose around the hooks of the tank and secure the gun as shown in Figure 12. Figure 10 1. Manual valve 2. Barb 3. Hose 4. Hose clamp 2.
PAGE 8
Operation 7 WARNING Installing the Electrical Harness Fluid under pressure can penetrate skin and cause injury. • Keep your body and hands away from nozzles that eject high pressure fluid. • Do not aim the sprayer at any person or animal. • Ensure that all fluid hoses and lines are in good condition and all connections and fittings are tight before applying pressure to the system. • Use cardboard or paper to find leaks. • Safely relieve all pressure in the system before performing any work on it.
PAGE 9
protection. Contact an Authorized Toro Dealer to obtain a Toro heat shield blanket kit for turf sprayers. by setting the pressure to maximum with the rate control switch and then adjusting the throttle speed until the desired pressure is obtained. Switching from Boom Spray Mode to Hand Spray Mode Note: The maximum recommended operating pressure of the hand spray gun kit is 150 psi. 1. Stop the machine and set the parking brake.
PAGE 10
Switching from Hand Spray Mode to Boom Spray Mode 1. Press the rate control switch to reduce the pressure. 2. Set the spray selection switch to the off position. 3. Direct the spray gun nozzle at an area where it is safe to spray, release the trigger lock, and pull the trigger until all remaining fluid is out of the hose, then set the trigger lock. 4. Wrap the hose around the hooks of the tank and secure the gun as shown in Figure 14.
PAGE 11
Notes: 11
PAGE 12