Installation Instructions

ManualsBrandsToro ManualsAttachmentsEductor Kit, Multi-Pro 5800 Turf Sprayer

FormNo.3385-176RevA

EductorKit

Multi-Pro5800TurfSprayer

ModelNo.41612—SerialNo.314000001andUp

InstallationInstructions

Thiskitisdesignedtoaidinthemixingofchemicalsin

preparationforturfsprayapplicationsonwell-maintained

lawnsinparks,golfcourses,sportselds,andoncommercial

grounds.Itisadedicatedattachmentforaturfspray

applicationvehicleandisintendedtobeusedbyprofessional,

hiredoperatorsincommercialapplications.

ThisproductcomplieswithallrelevantEuropeandirectives;

fordetails,pleaseseetheseparateproductspecicDeclaration

ofConformity(DOC)sheet.

Readthismanualcarefullytolearnhowtooperateand

maintainyourproductproperly.Theinformationinthis

manualcanhelpyouandothersavoidinjuryandproduct

damage.AlthoughTorodesignsandproducessafeproducts,

youareresponsibleforoperatingtheproductproperlyand

safely.

YoumaycontactTorodirectlyatwww .Toro.comforproduct

andaccessoryinformation,helpndingadealer,ortoregister

yourproduct.

WARNING

CALIFORNIA

Proposition65Warning

Thisproductcontainsachemicalorchemicals

knowntotheStateofCaliforniatocausecancer,

birthdefects,orreproductiveharm.

Useofthisproductmaycauseexposureto

chemicalsknowntotheStateofCalifornia

tocausecancer,birthdefects,orother

reproductiveharm.

Wheneveryouneedservice,genuineToroparts,oradditional

information,contactanAuthorizedServiceDealerorToro

CustomerServiceandhavethemodelandserialnumbersof

yourproductready.Figure1illustratesthelocationofthe

modelandserialnumbersontheproduct.

G013916

Figure1

1.Modelandserialnumberplate

ModelNo.

SerialNo.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3385-176*A

Summary of content (20 pages)

PAGE 1
Form No. 3385-176 Rev A Eductor Kit Multi-Pro 5800 Turf Sprayer Model No. 41612—Serial No. 314000001 and Up Installation Instructions This kit is designed to aid in the mixing of chemicals in preparation for turf spray applications on well-maintained lawns in parks, golf courses, sports fields, and on commercial grounds. It is a dedicated attachment for a turf spray application vehicle and is intended to be used by professional, hired operators in commercial applications.
PAGE 2
Safety WARNING Chemical substances used in the spray system may be hazardous and toxic to you, bystanders, animals, plants, soils, or other property. • Carefully read and follow the chemical warning labels and Material Safety Data Sheets (MSDS) for all chemicals used, and protect yourself according to the chemical manufacturer's recommendations.
PAGE 3
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 Description Qty. Eductor valve assembly O-ring Bolt (M8 –1.
PAGE 4
Procedure Description 1 1 1 1 1 1 1 Supply hose Gasket Worm-screw clamp Hose clamp Hose adapter Switch 10–amp fuse 6 7 Use Qty. Install the supply hose. Install the dash switch. Note: Determine the left and right sides of the machine from the normal operating position. 4. Locate the fly nut securing the agitation hose to the agitation valve body. Loosen the fly nut to allow space for the valve body fasteners to be removed (Figure 4).
PAGE 5
1 2 12. Insert the adapter removed previously to the open side of the eductor valve over the exposed ends of the bolts. 3 13. Install a bracket to the mount rail, and secure it with 2 bolts and 2 locknuts, but don’t tighten them at this time. Note: The bracket may already be installed from a previous kit installation. 14. Slide the bracket over the exposed threads of the bolts closest to the mount rail. Secure the bracket to the valve assembly with 2 locknuts. Don’t tighten at this time. 4 5 6 4 15.
PAGE 6
the tank strap and the upper hole with the upper bolt in the tank strap as shown in Figure 9. 1 2 3 G013922 4 Figure 8 21. Move the worm clamp into position over the adapters and tighten to create the seal between them. G013925 Figure 9 22. Locate the connector on the main wiring harness labeled eductor. Connect the eductor valve to the main harness using the labeled connector. 2 1. Main support frame assembly 3. Tank strap, rear 2. Exposed bolt, top 4. Exposed bolt, side 4.
PAGE 7
2 1 3 4 G013929 Figure 12 1. Cradle arm, left 2. Pivot housing Figure 11 1. Back plate assembly 7. Handle 2. Hair pin 8. Bolt (3/8 x 1–1/4 inches) 3. Flat washer 4. Bushing 9. Right cradle arm 10. Main support frame assembly 5. Pivot pin 11. Cradle arm axle 6. Jam nut (3/8 inch) 12. Pivot housing A. Start by installing the right cradle arm to the frame. The right cradle arm is denoted by have the long axle. B. Insert the axle through the hinge shaft. C.
PAGE 8
plate assembly of the cradle to compress the spring tabs midway (Figure 14). 3 1 2 Installing the Latching Components Parts needed for this procedure: 2 Spring 3 Installing the Springs 1. Install the spring in the hole in the lower end of the angled tab on the side of the frame assembly (Figure 13). G013932 Figure 14 1. Spring tab under pressure 3. Spring tab 2. Back plate 1 2 5.
PAGE 9
4 Installing the Eductor Parts needed for this procedure: 1 Eductor 1 Handle 2 Flange-head bolt 1 Spring clamp 2 Bolt (#10-24 x 1/2 inch) 2 Locknut (#10-24) 4 Bolt (3/8 x 1 inch) 4 Locknut (3/8 inch) 2 Flange-head nut 3 Hex-head bolt 1 Latch post 1 Latch handle 1 T-valve 1 Gasket 1 Worm-screw clamp Figure 16 1. Handle 6. Flange-head bolt 2. Eductor 7. Locknut (#10-24) 3. Flange-head nut 8. Latch post 4. Spring clamp 9. Extension bracket 5. Bolt (#10-24 x 1/2 inch) 10.
PAGE 10
. Tighten the fasteners securing the eductor to the cradle. Note: Torque the fasteners to 36-45 N-m (27-33 ft-lb). 11. Tighten the 2 set screws on the left pivot arm. 12. Check the overall position of the eductor assembly on the tank strap. Note: The eductor should be upright, in the transport position. Loosen the lower locknut on the frame assembly securing it to the tank. Do not remove the locknut. Adjust the position as necessary and tighten the locknut. Make sure that the strap is secure to the tank.
PAGE 11
Installing the Bulkhead 5 1. Open the main tank lid and remove the filter screen. 2. Install the bulkhead and the O-ring up from inside the tank through the previously cut opening (Figure 21). Installing the Forward Hose 1 Parts needed for this procedure: 1 Bulkhead 1 O-ring 1 Locking ring 2 Retaining fork 1 Forward hose assembly 1 Gasket 1 Worm-screw clamp 1 R-clamp 2 3 4 1 Carriage bolt (5/16 x 1 inch) 1 Lock nut (5/16 inch) G014022 Figure 21 Drilling the Tank 1.
PAGE 12
4. Install a lock nut over the bolt in the R-clamp and finger tighten at this time (Figure 22). 6 Note: This will allow for later adjustment. 5. Attach the other end of the hose to the forward-facing opening of the eductor using a gasket and worm-screw clamp (Figure 23). Installing the Supply Hose Parts needed for this procedure: 1 Supply hose 1 Gasket 1 Worm-screw clamp 1 Hose clamp 1 Hose adapter Procedure 1.
PAGE 13
1 2 7 3 Installing the Dash Switch Parts needed for this procedure: G014018 Switch 1 10–amp fuse Procedure Figure 26 1. Rear hose 2. Relief hose 1 1. Locate the plug for the eductor switch on the dash (Figure 28). 3. Eductor valve 1 3. Staying under the agitation hose but above the left side mount for the center boom, route the hose upward to the eductor valve assembly (Figure 26). G014023 2 4. Slide a loosened hose clamp over the open end of the hose (Figure 27). 1 4 3 Figure 28 1.
PAGE 14
1 2 G0151 18 Figure 29 1. Fuse block 2. 10–amp fuse 7. Adjust the agitation bypass valve as outlined in your Operator’s Manual. 8 Finishing the Installation Parts needed for this procedure: 1 Suction lance and hose (optional) Procedure Note: The suction lance and hose are optional accessories. Contact your Authorized Toro Distributor for more information. Retain the suction lance and hose for later use. Read and retain the remaining documentation on using the Chemical Pre-Mix Kit.
PAGE 15
Handles and Transport Strap Operation Use the upper and lower handles to raise and lower the eductor and to lock it into the Transport position. CAUTION Chemicals are hazardous and can cause personal injury. Main Valve Use the main valve to introduce chemicals from the eductor into the hose leading to the main tank. • Read the directions on the chemical labels before handling the chemicals and follow all manufacturer recommendations and precautions.
PAGE 16
Raising the Eductor Starting the Eductor 1. Lift the lower handle to raise the eductor while slightly tipping it toward the tank. Note: Close the eductor hopper valve and hopper rinse ball valve(s) before starting the eductor. 2. Guide the tongue under the crossbar with the welded tab in the upper portion of the frame assembly. 1. Lower the eductor. 2. Open the lid to check for foreign objects which may hinder performance or contaminate the system. 3.
PAGE 17
2 1 G016600 Figure 32 1. Suction lance 2. Eductor 2. Use the free end of the lance to pierce the bag or container to vacuum powdered or liquid chemical. 3. Place the lance end into a clean container of water to rinse the lance assembly. 4. Remove the lance body from eductor and drain any remaining fluid into the hopper. 5. Close the hopper valve (red handle). Shutting down the Eductor 1. Close all the valves. Note: Close the hopper valve first. 2. Remove all chemical residue. 3.
PAGE 18
Troubleshooting Problem The eduction rate is low. Possible Cause 1. There is a lack of flow and pressure to the eductor system. 1. Increase the pump speed. Turn the agitation throttling toward the closed position. 2. The outlet/Inlet hose is obstructed. 2. Disassemble and remove any obstructions. 3. Use only sweeping turns with flexible hoses. 3. Fittings with elbows or other flow-restrictions are in the eductor outlet. There is no rinsing or flushing action. There are leaks at the fittings.
PAGE 19
Notes: 19
PAGE 20
The Toro Total Coverage Guarantee A Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).