Installation Instructions

ManualsBrandsToro ManualsAttachmentsEductor Kit, Multi-Pro 5800 Turf Sprayer

FormNo.3365-863RevC

EductorKit

Multi-Pro

5800TurfSprayer

ModelNo.41612—SerialNo.311000001andUp

InstallationInstructions

TheEductorKitisdesignedtoaideinthemixingof

chemicalsinpreparationforturfsprayapplicationson

well-maintainedlawnsinparks,golfcourses,sports

elds,andoncommercialgrounds.Itisadedicated

attachmentforaturfsprayapplicationvehicleandis

intendedtobeusedbyprofessional,hiredoperatorsin

commercialapplications.

ThisproductcomplieswithallrelevantEuropean

directives,fordetailspleaseseetheseparateproduct

specicDeclarationofConformity(DOC)sheet.

Note:Ifinstallingkitmodelnumbers41604Pro

ControlXPSprayKit,41612EductorKit,41613

ElectricHoseReelKit,and41614TankRinseKit,it

isadvisabletoassemblethemintothemanifoldvalve

assemblyatthesametime.

Readthismanualcarefullytolearnhowtooperateand

maintainyourproductproperly.Theinformationin

thismanualcanhelpyouandothersavoidinjuryand

productdamage.AlthoughTorodesignsandproduces

safeproducts,youareresponsibleforoperatingthe

productproperlyandsafely.

YoumaycontactTorodirectlyatwww .Toro.comfor

productandaccessoryinformation,helpndinga

dealer,ortoregisteryourproduct.

Wheneveryouneedservice,genuineToroparts,or

additionalinformation,contactanAuthorizedService

DealerorToroCustomerServiceandhavethemodel

andserialnumbersofyourproductready.

Figure1

illustratesthelocationofthemodelandserialnumbers

ontheproduct.

G013916

Figure1

1.Modelandserialnumberplate

ModelNo.

SerialNo.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (20 pages)

PAGE 1
Form No. 3365-863 Rev C Eductor Kit Multi-Pro® 5800 Turf Sprayer Model No. 41612—Serial No. 311000001 and Up Installation Instructions The Eductor Kit is designed to aide in the mixing of chemicals in preparation for turf spray applications on well-maintained lawns in parks, golf courses, sports fields, and on commercial grounds. It is a dedicated attachment for a turf spray application vehicle and is intended to be used by professional, hired operators in commercial applications.
PAGE 2
Safety WARNING Chemical substances used in the spray system may be hazardous and toxic to you, bystanders, animals, plants, soils or other property. • Carefully read and follow the chemical warning labels and Material Safety Data Sheets (MSDS) for all chemicals used and protect yourself according to the chemical manufacturer’s recommendations.
PAGE 3
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 7 8 Description Qty. Use Eductor valve assembly O-ring Bolt (M8 -1.
PAGE 4
1 3 2 1 Installing the Eductor Valve Parts needed for this procedure: 1 Eductor valve assembly 1 O-ring 4 Bolt (M8 -1.25 x 146 mm) 1 Bracket (Bracket may already be installed from a previous kit installation) 8 4 5 6 5 G013918 7 Figure 4 Procedure 1. 2. 3. 4. 1. Move to the rear of the machine and locate the boom valve assembly on the boom valve mount bracket. 2. Loosen, but do not remove, the bolts securing the boom valve assembly to the mounting bracket (Figure 3).
PAGE 5
Note: The O-rings must be installed properly to ensure there are no leaks. 1 2 3 16. Tighten all the bolts in a crisscrossing pattern a little at a time to ensure the O-ring seats properly and to avoid leads. Make sure the bracket is free to adjust as the valves are mated (Figure 7). The maximum torque is 24-30 in-lbs (271-339 N-cm). 4 G013921 1 7 6 5 G013920 3 Figure 6 1. 2. 3. 4. Eductor valve O-ring Lock nut, existing Bracket and fasteners 5. Gasket, existing 6. Adapter, existing 7.
PAGE 6
1 21. Move the worm clamp into position over the adapters and tighten to create the seal between them. 2 22. Locate the connector on the main wiring harness labeled ’eductor’. Connect the eductor valve to the main harness using the labeled connector.
PAGE 7
1 2 1 2 3 4 5 6 8 11 3 7 4 G013924 G013929 10 9 Figure 12 Figure 11 1. Back plate assembly 2. Main support frame assembly 3. Bushing, small 4. Pivot pin 5. Jam nut (3/8 inch) 6. Handle 1. Cradle arm, left 2. Pivot housing 7. Cradle arm, right 8. Bolt (3/8 x 1-1/4 inches) 9. Axle, cradle arm 10. Bushing, large 11. Pivot housing 3. Set screw 4. Holes in cradle arm. 3 Installing the Latching Components A. Start by installing the right cradle arm to the frame.
PAGE 8
opposing end reaches the protruding post on the cradle arm (Figure 13). 4 1 3. Make sure the spring end is seated properly in the groove in the post (Figure 13). 4. Repeat for the other side. 5. Tighten the two set screws. 2 3 G013933 Figure 15 Adjust the Tongue Position 1. Tongue plate lip 2. Fasteners Move the cradle assembly into the upper, “transport” position to adjust the tongue. 3. Slot in plate 4.
PAGE 9
G013934 up into the transport position. This will allow for further adjustment. 5. Carefully raise the eductor in the cradle assembly up to the transport position: 1 6 2 G013935 3 5 Figure 18 4 Figure 16 1. Eductor 2. Spring clamp 3. Bolt (#10-24 x 1/2 inch) A. Lift the lower handle to raise the eductor while at the same time slightly tipping it toward the tank (Figure 18). 4. Lock nut (#10-24) 5. Bolt 6. Handle B.
PAGE 10
Installing the Bulk Head the lock nut. Make sure the strap is secure to the tank. 1. Locate the S93 bulkhead in loose parts. 2. Open the main tank lid and remove the filter screen. 5 3. Install the bulkhead as shown in Figure 21. 1 Installing the Forward Hose 2 Parts needed for this procedure: 1 Bulkhead, S93 1 O-ring, large 1 Locking ring 1 Retaining fork 1 R-clamp 1 Carriage bolt (5/16 x 1 inch) 1 Lock nut (5/16 inch) 1 Forward hose assembly 3 4 G014022 Figure 21 1.
PAGE 11
1 2 3 4 the bolt in the R-clamp and finger tighten at this time (Figure 23). This will allow for later adjustment. 4. Route the open end of the hose rearward toward the front facing opening of the valve on the eductor assembly Connecting to the Eductor 1. Install the remainder of the hose to forward facing, threaded opening of the eductor (Figure 24). Secure it to the eductor assembly with the plastic nut. 5 1 2 G014013 Figure 22 1. R-clamp 2. Long bolt 4. Lock nut 5.
PAGE 12
1 6 2 3 Installing the Supply Hose Parts needed for this procedure: 1 Supply hose assembly 1 Hose clamp G014018 Connecting to the Eductor Figure 27 1. Locate the supply hose in loose parts. Find the end with the straight barbed connector, plastic nut and hose clamp assembled to it. 1. Rear hose 2. Relief valve 2. Staying under the agitation hose but above the left side mount for the center boom, route the hose upward to the eductor valve assembly (Figure 27). 2.
PAGE 13
1 7 2 Installing the Dash Switch Parts needed for this procedure: 1 Switch, eductor 1 10 amp fuse Procedure G0151 18 Figure 30 1. Locate the plug for the eductor switch on the dash (Figure 29). It second plug over from the ignition key. 1. Fuse block 2. 10 Amp fuse 7. Adjust the agitation bypass valve as outlined in your Operator’s Manual. 1 G014023 2 8 Finishing the Installation 4 Parts needed for this procedure: 3 Figure 29 1. Connector for eductor, from main harness 2.
PAGE 14
Main Valve Operation Use the main valve to introduce chemicals from the eductor into hose leading to the main tank. CAUTION Chemicals are hazardous and can cause personal injury. 1 • Read the directions on the chemical labels before handling the chemicals and follow all manufacturer recommendations and precautions. 2 • Keep chemicals away from your skin. Should contact occur, wash the affected area thoroughly with soap and clean water.
PAGE 15
Eductor Switch • Avoid stationary spraying when conditions are very hot and/or dry, as turf can be more stressed during these periods. • Avoid parking on the turf while stationary spraying. Park on a cart path whenever possible. • Minimize the amount of time the machine is left running over any particular area of turf. Both time and temperature affect how much the grass may be damaged. • Set the engine speed as low as possible to achieve the desired pressure and flow.
PAGE 16
6. Open hopper valve (red handle) located on the bottom of hopper. 7. Unlock and open lid slowly by turning cover counterclockwise. 2. Use the free end of the lance to pierce bag or container to vacuum powdered or liquid chemical. 3. Place lance end into a clean container of water to rinse lance assembly. 4. Remove lance body from Eductor and drain any remaining fluid into hopper. Loading Liquid or Powdered Chemical into Hopper 5. Close hopper valve (red handle). 1.
PAGE 17
Troubleshooting Problem Low eduction rate Possible Cause 1. Lack of flow and pressure to the eductor system 1. Increase pump speed. Turn agitation throttling toward the closed position. 2. Outlet/Inlet hose obstruction. 2. Disassemble and remove any obstructions. 3. Use only sweeping turns with flexible hoses. 3. Fittings with elbows or other flow-restrictions are in the eductor outlet. No rinsing or flushing action Leaks at the fittings Corrective Action 1. Plugged or clogged bottle rinse nozzle.
PAGE 18
Notes: 18
PAGE 19
Notes: 19
PAGE 20