Installation Instructions

ManualsBrandsToro ManualsAttachmentsElectric Hose Reel Kit, Multi-Pro 5800 Turf Sprayer

FormNo.3365-876RevC

ElectricHoseReelKit

Multi-Pro

5800TurfSprayer

ModelNo.41613—SerialNo.311000001andUp

InstallationInstructions

TheElectricHoseReelKitisadedicatedattachment

foraturfsprayapplicationvehicleandisintendedto

beusedbyprofessional,hiredoperatorsincommercial

applications.Itisprimarilydesignedforsprayingon

well-maintainedlawnsinparks,golfcourses,sports

elds,andoncommercialgrounds.

ThisproductcomplieswithallrelevantEuropean

directives,fordetailspleaseseetheseparateproduct

specicDeclarationofConformity(DOC)sheet.

Note:Ifinstallingkitmodelnumbers41604Pro

ControlXPSprayKit,41612EductorKit,41613

ElectricHoseReelKit,and41614TankRinseKit,it

isadvisabletoassembletehmintothemanifoldvalve

assemblyatthesametime.

Readthismanualcarefullytolearnhowtooperateand

maintainyourproductproperly.Theinformationin

thismanualcanhelpyouandothersavoidinjuryand

productdamage.AlthoughTorodesignsandproduces

safeproducts,youareresponsibleforoperatingthe

productproperlyandsafely.

YoumaycontactTorodirectlyatwww.Toro.comfor

productandaccessoryinformation,helpndinga

dealer,ortoregisteryourproduct.

Wheneveryouneedservice,genuineToroparts,or

additionalinformation,contactanAuthorizedService

DealerorToroCustomerServiceandhavethemodel

andserialnumbersofyourproductready.

Figure1

illustratesthelocationofthemodelandserialnumbers

ontheproduct.

G013884

Figure1

1.Modelandserialnumberplate

ModelNo.

SerialNo.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (16 pages)

PAGE 1
Form No. 3365-876 Rev C Electric Hose Reel Kit Multi-Pro® 5800 Turf Sprayer Model No. 41613—Serial No. 311000001 and Up Installation Instructions The Electric Hose Reel Kit is a dedicated attachment for a turf spray application vehicle and is intended to be used by professional, hired operators in commercial applications. It is primarily designed for spraying on well-maintained lawns in parks, golf courses, sports fields, and on commercial grounds.
PAGE 2
Safety or death. Hot liquids and chemicals can also cause burns or injury. If any part of the body comes in contact with the spray stream, immediately consult a physician familiar with injected fluid injuries. This manual identifies potential hazards and has safety messages identified by the safety alert symbol (Figure 2), which signals a hazard that may cause serious injury or death if you do not follow the recommended precautions.
PAGE 3
120-0618 1. Warning—read the Operator’s Manual. 2. Crushing hazard of hand, rollers—warning, hose reel self winds; stay away from moving parts, keep all guards and shields in place.
PAGE 4
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 Description Use Qty.
PAGE 5
3 2 1 1 3 4 4 2 6 7 8 9 12 2 11 10 G013886 Figure 5 G013907 1. Lock nut Figure 3 1. Agitation valve 2. Bypass valve assembly 2. 3. 4. 5. 6. 3. Mount bracket 4. Fasteners, loosen but do not remove. 2. Loosen the long bolts and fasteners securing the valve assembly (Figure 4). Remove and retain all fasteners. Move the valve assembly to the right. A. Verify the existing O-ring is seated in the open end of the boom valve body. If is not at this time, locate it and install now. B.
PAGE 6
A. Remove the fitting securing the red pressure gauge tube to the elbow adapter. B. Locate the tee fitting in loose parts. Wrap the threaded end with the thread tape. C. Install the tee fitting to the elbow adapter with the tee facing toward the tank. D. Install the fitting removed previously to the open end of the fitting. 1 G014224 2 3 2 Figure 7 Installing the Control Box 1. Pressure gauge tube from control box 2.
PAGE 7
2 3 1 Assembling the Frame Parts needed for this procedure: 3 1 Hose reel support 10 Flange-head bolt (3/8 x 1 inch) 10 Flange nut (3/8 inch) 2 Hose reel strap 1 Hose reel assembly 1 Flange-head bolt (5/16 x 1 inch) 1 Flange nut (5/16 inch) 10 Cable tie 4 G013901 Figure 9 1. Flange-head bolt (3/8 x 1 inch) 2. Lock nut (3/8 inch) 3. Hose reel straps 4. Hose reel support 3.
PAGE 8
4 Installing the Supply Hose Parts needed for this procedure: G014026 1 Hose 2 Hose clamp 1 Straight barb 1 Conduit 2 Cable ties 1 Figure 12 1. Boom support channel 7. Route the hoses around the mount frame and up to the open barb on the hose reel valve installed previously (Figure 12). Procedure 8. Slide a hose clamp over the open end of the hose and install the hose over the exposed barb in the valve. 1. Locate the reel hose and two hose clamps in loose parts. 1 2.
PAGE 9
1 5 Installing the Electrical Harness Parts needed for this procedure: 2 4 Plastic tie 1 Fuse, 50 Amp 2 Push in connector 3 G014137 Figure 15 1. Agitation ports Procedure 3. Electric hose reel harness, long end 2. Tank skid frame 1. Locate the electrical harness coming from the hose reel control box. Route the longer end of the harness with the ring terminals and a fuse connector across the rear of the tank skid and vehicle frame behind the boom actuator bracket (Figure 14).
PAGE 10
2 G014028 6 3 1 Connecting the Spray Hose 8 Parts needed for this procedure: 7 6 4 5 1 Long hose with fitting 1 Spray gun 1 Hose clamp, small Figure 17 1. Bolt, battery post 2. Fuse, 50 amp 3. Fuse holder, electric hose reel harness 4. Electric hose reel harness 5. Negative battery post 6. Battery 7. Lock nut, battery post Procedure 1. Wrap Teflon tape around the threads of the hose fitting on the long hose and install the fitting into the connecting tube on the reel (Figure 19). 8.
PAGE 11
2. Connect the free end of the long hose to the fitting on the spray gun (Figure 20). 4 G015041 Figure 20 1. Spray gun 2. Barb 3. Hose 4. Hose clamp 3. Secure the end of the hose with a small hose clamp. Ensure that the hose is fed through the guide opening before attaching the spray gun to the hose. 4. Connect the negative battery wire to the battery. 5. Press the hose wind button and carefully guide the hose onto the reel moving the hose from side to side to evenly distribute the hose.
PAGE 12
Operation Note: Use a heat shield blanket underneath the vehicle during stationary operation if additional heat protection is desired. Contact your Authorized Toro Dealer to obtain a Toro Heat Shield Blanket kit, for turf sprayers. WARNING Fluid under pressure can penetrate skin and cause injury. Switching from Boom Spray Mode to Hand Spray Mode • Keep your body and hands away from nozzles that eject high pressure fluid. 1. Stop the machine and set the parking brake.
PAGE 13
CAUTION Hands, loose clothing, long hair, and jewelry could get caught in the hose and reel while rewinding and cause injury. 2 1 • Keep your hands clear of the reel and hose while it is rewinding. • Do not wear loose clothing or jewelry and tie up long hair. G013889 4 2. Set the spray selection switch to the off position. 3 3.
PAGE 14
Maintenance Cleaning The hand sprayer needs to be flushed after each use. When rinsing the booms, switch the sprayer to hand spray mode and activate the spray gun trigger several times to thoroughly rince the hose assembly and the sprayer gun.
PAGE 15
Notes: 15
PAGE 16