Installation Instructions

ManualsBrandsToro ManualsAttachmentsTank Rinse Kit, Multi-Pro 5800 Turf Sprayer

FormNo.3368-115RevB

TankRinseKit

Multi-Pro

5800TurfSprayer

ModelNo.41614—SerialNo.311000001andUp

InstallationInstructions

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

TheRinseKitisdesignedtoremoveresidualchemicals

fromasprayertankandaffectedhoses.Itisadedicated

attachmentforaturfsprayapplicationvehicleandis

intendedtobeusedbyprofessional,hiredoperatorsin

commercialapplications.

ThisproductcomplieswithallrelevantEuropean

directives,fordetailspleaseseetheseparateproduct

specicDeclarationofConformity(DOC)sheet.

Readthismanualcarefullytolearnhowtooperateand

maintainyourproductproperly.Theinformationin

thismanualcanhelpyouandothersavoidinjuryand

productdamage.AlthoughTorodesignsandproduces

safeproducts,youareresponsibleforoperatingthe

productproperlyandsafely.

YoumaycontactTorodirectlyatwww.Toro.comfor

productandaccessoryinformation,helpndinga

dealer,ortoregisteryourproduct.

Wheneveryouneedservice,genuineToroparts,or

additionalinformation,contactanAuthorizedService

DealerorToroCustomerServiceandhavethemodel

andserialnumbersofyourproductready.Figure1

illustratesthelocationofthemodelandserialnumbers

ontheproduct.

G014295

Figure1

1.Modelandserialnumberplate

ModelNo.

SerialNo.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (16 pages)

PAGE 1
Form No. 3368-115 Rev B Tank Rinse Kit Multi-Pro® 5800 Turf Sprayer Model No. 41614—Serial No. 311000001 and Up Installation Instructions Note: Determine the left and right sides of the machine from the normal operating position. The Rinse Kit is designed to remove residual chemicals from a sprayer tank and affected hoses. It is a dedicated attachment for a turf spray application vehicle and is intended to be used by professional, hired operators in commercial applications. Model No. Serial No.
PAGE 2
Safety • Properly dispose of unused chemicals and chemical containers as instructed by the chemical manufacturer and your local codes. Also read the safety and operation instructions in the vehicle Operator’s Manual. • Chemicals and fumes in the tanks are dangerous; never enter the tank or place your head over or in the opening. Chemical Safety • Follow all local/state/federal requirements for the spraying of chemicals.
PAGE 3
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 7 Description Use Qty.
PAGE 4
1 2 Preparing the Machine Installing the Rinse Tank Bulkhead Fitting No Parts Required Parts needed for this procedure: Procedure 1. Move the sprayer onto a level surface, set the parking brake, stop the pump, stop the engine, and remove the ignition key. 2. Drain the contents of the tank to remove any solution in lines. Refer to the Operator’s Manual for more information.
PAGE 5
3 3 Installing the Rinse Tank Parts needed for this procedure: G014229 1 2 Figure 3 1. Bulkhead fitting, wire attached 2. Bottom hole, rinse tank 3. Filler cap 2 Rinse tank strap 2 Bolt 4 Washer 2 Lock nut 1 Carriage bolt 1 Lock nut Prepare the Tank F. Move the bulkhead fitting into position making sure the clear gasket seats against the interior wall of the rinse tank (Figure 3). 1. Loosen the bolts securing the valve mounting rail to the frame (Figure 6). 3.
PAGE 6
Install the Rinse Tank 2 3 1 1. Install the rinse tank as shown in (Figure 9). 4 5 1 6 7 G014232 Figure 7 1. 2. 3. 4. Lock nut Bolt Washer Lock nut 5. Right rear tank strap 6. Retaining fork 7. Supply hose G014233 Figure 9 1. Rinse tank 5. Remove the retaining fork securing the fitting and remove the hose. Retain all parts. 2. Install the rinse tank straps to hardware installed previously on the rear strap tank straps. 6.
PAGE 7
Note: Once the rinse tank has been initially filled the rinse tank strap fasteners should be checked and tightened if necessary as the weight of the liquid can further seat the tank against the frame. 2 1 4 Installing the Rinse Nozzles Parts needed for this procedure: 2 Rinse nozzle 2 Bulkhead fitting 2 Shoulder bolt 2 Bushing 2 Rinse vane 2 Gasket 2 Plastic flange nut G014245 Figure 12 1. Hole saw 2. Drill mark, behind lid 5. After drilling the hole, remove any rough edges in the cut.
PAGE 8
1 1 2 2 3 G014247 4 Figure 16 1. Assembly nozzle bulkhead 2. 90 degree fitting 5 G014252 5. Direct the hose barb to the right side of the machine. Figure 14 1. Bulkhead fitting 2. Rinse nozzle 3. Bushing 4. Rinse vane 5. Shoulder bolt 6. Move to the forward hole in the tank. 7. Install a nozzle assembly up through the drilled hole (Figure 17). A. Install a rinse vane and bushing over the shoulder bolt. 1 B. Install all parts to the rinse nozzle . 2 C.
PAGE 9
3. Locate the straight barb hose connectors in loose parts. Install a connector to the pump inlet and outlet openings (Figure 20). 2 1 1 2 2 G014250 Figure 18 1. Assembly nozzle bulkhead 2. 90 degree fitting G014290 10. Direct the hose barb to the right side of the machine. Figure 20 1. Pump 5 4. Locate the harness coming from the pump. Locate the connector labeled Rinse Pump on the main wiring harness at the rear of the tank. 5. Connect the pump to the main wiring harness.
PAGE 10
1 G014292 1 1 2 4 G014291 2 5 2 4 1 3 Figure 21 1. Barb, rinse nozzle 2. Rinse nozzle hose 1 3. Hose clamp 4. Tee fitting 3 Figure 22 1. Hose clamp 2. Long supply hose 3. Filter 3. Install a hose over the barb of the rinse nozzle (Figure 21). Repeat the procedure for the other rinse nozzle barb. 4. Cut hose 5. Pump 6. Slide the hose clamp over the barb and tighten to secure. 4. Slide a hose clamp over the barb and tighten to secure. 7. Install a hose clamp over each end of the short hose.
PAGE 11
Install the Rinse Tank Hose 7 1. Locate the rinse tank hose in loose parts. 2. Install a hose clamp over one end of the hose. Installing the Delay Timer and Dash Switch 3. Install one end of the hose to the 90 degree fitting at the bottom of the rinse tank (Figure 24). 5 6 Parts needed for this procedure: 2 1 3 2 4 Delay timer 1 Fuse, 40 Amp 1 Dash switch 1 Relay 1 Power relay 2 Screw #10–24 G0151 12 Figure 24 1. Rinse hose 2. Hose clamp 3.
PAGE 12
Operation 5. Locate relay and power relay in line with the other relays of the same style, and mount to the panel with #10–24 screws. Rinse Kit Operation 6. Locate the proper connectors on the main harness and connect them to the relay and power relay. The use of the Rinse Kit will result in a rinsate; a diluted solution of residual chemicals. In many cases it is appropriate to apply the rinsate onto the treated areas.
PAGE 13
The rinse cycle can be repeated again as necessary or two more timed rinse cycles. will extinguish signaling that power to the pump has been shut off and the pump will stop running. The switch will remain in the up position until moved to the center or neutral position. When the switch is in the Neutral position the power is not supplied to the pump and the rinse kit is Off. The light on the switch is not illuminated. Pressing the switch Down engages a momentary switch.
PAGE 14
Maintenance Storage Inspect the Filter Drain the pump inlet line, outlet line, and filter line prior to storage for 30 days or more. Service Interval: After the first 5 hours Every 50 hours Check the filter for any signs of damage. Replace if any damage is found. Inspect Rinse System of Leaks and Damage Service Interval: Before each use or daily—Inspect the hoses for leaks. After the first 5 hours—Inspect hoses for damage.
PAGE 15
Notes: 15
PAGE 16