Operator's Manual

ManualsBrandsToro ManualsSprayersPivoting Hose Reel Kit, 2015 and After Multi-Pro 5800 Turf Sprayer

FormNo.3394-637RevA

PivotingHoseReelKit

2015andAfterMulti-Pro5800TurfSprayer

ModelNo.41621—SerialNo.315000001andUp

Operator'sManual

Note:Formodelsbuiltin2014orbefore,thePivotingHose

ReelFinishingKitisneeded.

Introduction

Readthismanualcarefullytolearnhowtooperateand

maintainyourproductproperly.Theinformationinthis

manualcanhelpyouandothersavoidinjuryandproduct

damage.AlthoughTorodesignsandproducessafeproducts,

youareresponsibleforoperatingtheproductproperlyand

safely.

YoumaycontactTorodirectlyatwww.Toro.comforproduct

safetyandoperationtrainingmaterials,accessoryinformation,

helpndingadealer,ortoregisteryourproduct.

Wheneveryouneedservice,genuineToroparts,oradditional

information,contactanAuthorizedServiceDealerorToro

CustomerServiceandhavethemodelandserialnumbersof

yourproductready.Figure1illustratesthelocationofthe

modelandserialnumbersontheproduct.

Figure1

1.Modelandserialnumberplate

ModelNo.

SerialNo.

WARNING

CALIFORNIA

Proposition65Warning

Thisproductcontainsachemicalorchemicals

knowntotheStateofCaliforniatocausecancer,

birthdefects,orreproductiveharm.

Useofthisproductmaycauseexposureto

chemicalsknowntotheStateofCalifornia

tocausecancer,birthdefects,orother

reproductiveharm.

Note:ThisproductcomplieswithallrelevantEuropean

directives.Fordetails,pleaseseetheDeclarationof

Incorporation(DOI)atthebackofthispublication.

Determinetheleftandrightsidesofthemachinefromthe

normaloperatingposition.

Important:PTFEtapeisrequiredfortheinstallation

ofthiskit.

Important:Youwillneedanon-petroleum-based

lubricant,suchasvegetableoil,toinstallthiskit.

Safety

Improperuseormaintenancebytheoperatoror

ownercanresultininjury.Toreducethepotential

forinjury,complywiththesesafetyinstructionsand

alwayspayattentiontothesafetyalertsymbol,which

meansCaution,Warning,orDanger—personalsafety

instruction.Failuretocomplywiththeinstructionmay

resultinpersonalinjuryordeath.

Readalsothesafetyandoperationinstructionsinthevehicle

Operator'sManual.

•Donotaimthehandsprayeratanypersonoranimal.

Fluidsunderhighpressurecanpenetrateskinandcause

severeinjury,possiblyresultinginamputationordeath.

Hotliquidsandchemicalscanalsocauseburnsorinjury.

Ifanypartofthebodycomesincontactwiththespray

stream,immediatelyconsultaphysicianfamiliarwith

injecteduidinjuries.

•Donotplaceyourhandoranyotherpartofyourbodyin

frontofthespraynozzle.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3394-637*A

Summary of content (16 pages)

PAGE 1
Form No. 3394-637 Rev A Pivoting Hose Reel Kit 2015 and After Multi-Pro 5800 Turf Sprayer Model No. 41621—Serial No. 315000001 and Up Operator's Manual Note: For models built in 2014 or before, the Pivoting Hose Reel Finishing Kit is needed. Introduction Read this manual carefully to learn how to operate and maintain your product properly. The information in this manual can help you and others avoid injury and product damage.
PAGE 2
• Do not leave the equipment under pressure when you CAUTION are not present. Chemicals are hazardous and can cause personal injury. • Do not use the hand sprayer if the hose, trigger lock, nozzle, or any other part is damaged or missing. • Read the directions on the chemical labels before handling the chemicals and follow all manufacturer recommendations and precautions. • Do not use the hand sprayer if there are any leaks in any hoses, fittings, or other components. • Do not spray near power lines.
PAGE 3
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 Description Qty.
PAGE 4
Procedure 4 5 Description Qty. 1 1 1 3 1 1 1 1 1 1 1 1 1 1 1 1 Control valve T-fitting Hose clamp Cable tie R-clamp Hose (71 inches) Clamp 90-degree fitting Tube coupler Nut (1/4-20 inch) Flange nut (3/8-16 inch) Pressure transducer wire Bolt (1/4-20 x 3/4 inch) Spray-gun hose with fitting Spray gun Small hose clamp 4 Use Install the control valve. Connect the spray hose.
PAGE 5
1 2 Preparing the Machine Installing the Hose-Reel Frame No Parts Required Parts needed for this procedure: Procedure 1. Ensure that the machine is empty of all fluids. Note: If chemicals have been used in the machine, flush the system thoroughly with clean water; refer to your vehicle Operator's Manual for instructions. 2. Park the machine on a flat area, set the parking brake, stop the pump, stop the engine, and remove the ignition key. 3. Disconnect the negative battery terminal from the battery.
PAGE 6
1 3 4 2 Figure 2 1. Bolt (1/4-20 x 3/4 inch) 4. Flange nut (5/16-18 inch) 2. Upper bracket 5. Whiz bolt (5/16-18 x 1 inch, GR5) 3 5 g0279 55 Figure 4 3. Nut (1/4-20 inch) 1. Bolt (3/8-16 inch) 4. Lower bracket 2. Lower support bracket 5. Bolt (3/8-16 x 3 1/2 inch) 3. Flange nut (3/8-16 inch) 2. Secure the back side of the upper bracket using 1 U-bolt, 1 bolt (3/8-16 x 1 inch, GR5), and 3 flange nuts (3/8-16 inch) as shown in Figure 3. 4.
PAGE 7
3 Installing the Switch Box and Hose Reel Parts needed for this procedure: Figure 6 1 Wiring harness 1 Switch box assembly 1 Thrust washer 1. Flange nut (5/16-18 inch) 3. Jam nut (5/16-18 inch) 1 Snap ring 2. Shoulder bolt 4. Bolt (5/16-18 x 1 inch, GR5) 1 Hose reel assembly 1 Spring pin 4 Washer (7/16 inch) 2 Flange nut (5/16-18 inch) 2 Bolt (5/16-18 x 1/4 inch, GR5) 1 Washer 4 Flange nut (3/8-16 inch) 4 Bolt (3/8-16 inch) 6.
PAGE 8
Figure 11 Figure 9 1. Thrust washer 1. Flange nut (3/8-16 inch) 3. Bolt (3/8-16 inch) 2. Washer (7/16 inch) 2. Snap ring 6. Install the washer and spring pin to the underside of the hose-reel frame (Figure 12). 3. Mount the switch box to the swivel plate using 2 bolts (5/16-18 x 1/4 inch, GR5) and 2 flange nuts (5/16-18 inch) as shown in Figure 10. Figure 12 1. Washer 7. Connect the remaining wiring harness plugs to the motor, the main harness power, and the hose reel kit plugs. Figure 10 1.
PAGE 9
2. Install the control valve assembly as shown in Figure 13. 4 3. Install the coupler into the open port on the 90-degree fitting (Figure 13 and Figure 14). Installing the Control Valve Note: The cap can be discarded. 4. Connect the hose-reel supply hose to the control valve using a hose clamp (Figure 13).
PAGE 10
5 Connecting the Spray Hose Parts needed for this procedure: 1 Spray-gun hose with fitting 1 Spray gun 1 Small hose clamp Figure 15 1. Pressure-gauge coupler Procedure 3. T-fitting 2. Pressure transducer wire 1. Wrap Teflon® tape around the threads of the hose fitting on the long hose, and install the fitting into the connecting tube on the reel (Figure 17). 9. Connect the hose (71 inches) to the hose barb on the hose reel assembly and secure the hose using a hose clamp as shown in Figure 16.
PAGE 11
Operation 5. Press the hose wind button, and carefully guide the hose onto the reel moving the hose from side to side to evenly distribute the hose. WARNING CAUTION Fluid under pressure can penetrate skin and cause injury. • Keep your body and hands away from nozzles that eject high-pressure fluid. • Do not aim the sprayer at any person or animal. • Make sure that all fluid hoses and lines are in good condition and that all connections and fittings are tight before applying pressure to the system.
PAGE 12
6. Set the engine to the desired speed, then engage the neutral engine-speed lock. Important: Do not use a pressure setting higher than 1034 kPa (150 psi) with the hand sprayer. Spraying with the Hand Sprayer 1. Pull out the desired amount of hose from the reel. Important: Do not pull the hose with the spray gun. Always hold the hose and pull on it directly. Pulling on the hose with the gun may break the fitting on the gun or damage the hose. 2. Release the trigger lock. 3.
PAGE 13
Notes: 13
PAGE 14
Declaration of Incorporation The Toro Company, 8111 Lyndale Ave. South, Bloomington, MN, USA declares that the following unit(s) conform(s) to the directives listed, when installed in accordance with the accompanying instructions onto certain Toro models as indicated on the relevant Declarations of Conformity. Model No. 41621 Serial No.
PAGE 15
International Distributor List Distributor: Country: Phone Number: Distributor: Phone Number: 57 1 236 4079 Colombia Japan 81 3 3252 2285 Czech Republic 420 255 704 220 420 255 704 Slovakia 220 Argentina 54 11 4 821 9999 Russia 7 495 411 61 20 Ecuador 593 4 239 6970 Finland 358 987 00733 Agrolanc Kft Balama Prima Engineering Equip. B-Ray Corporation Hungary Hong Kong Korea 36 27 539 640 852 2155 2163 82 32 551 2076 Maquiver S.A. Maruyama Mfg. Co. Inc. Mountfield a.s.
PAGE 16
Toro General Commercial Product Warranty A Two-Year Limited Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly warrant your Toro Commercial product (“Product”) to be free from defects in materials or workmanship for two years or 1500 operational hours*, whichever occurs first. This warranty is applicable to all products with the exception of Aerators (refer to separate warranty statements for these products).